Download or read book Influences of Stress driven Grain Boundary Motion on Microstructural Evolution in Nanocrystalline Metals written by Mohammad Aramfard and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanocrystalline (NC) metals with averaged grain size smaller than 100 nm have shown promising mechanical properties such as higher hardness and toughness than conventional coarse-grained metals. Unlike conventional metals in which the deformation is controlled by dislocation activities, the microstructural evolution in NC metals is mainly dominated by grain rotation and stress-driven grain boundary motion (SDGBM) due to the high density of grain boundaries (GBs). SDGBM is thus among the most studied modes of microstructural evolution in NC materials with particular interests on their fundamental atomistic mechanisms. In the first part of this thesis, molecular dynamics simulations were used to investigate the influences of Triple Junctions (TJs) on SDGBM of symmetric tilt GBs in copper by considering a honeycomb NC model. TJs exhibited asymmetric pinning effects to the GB migration and the constraints by the TJs and neighboring grains led to remarkable non-linear GB motion in directions both parallel and normal to the applied shear. Based on these findings, a generalized model for SDGBM in NC Cu was proposed. In the second part, the interaction of SDGBM with crack, voids and precipitates was investigated. It was found that depending on the GB structure, material type and temperature, there is a competition between different atomistic mechanisms such as crack healing, recrystallization and GB decohesion. It is hoped that the findings of this work could clarify the micro-mechanisms of various experimental phenomena such as grain refinement in metals during severe plastic deformation, which can be used to design optimized route of making stabilized bulk NC metals.
Download or read book Grain Boundary Segregation in Nanocrystructured Metallic Materials written by Jinyu Zhang and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of this chapter is to shed light on the effects of grain boundary segregation on microstructural evolution in nanostructured metallic materials as well as on their mechanical properties. Several key topics will be covered. First, a brief explanation of mechanical stress-driven grain growth in nanostructured Al, Ni, and Cu thin films will be provided in terms of a deformation mechanism map. It will become clear that the excess energy of grain boundaries enable the nanostructured metals to suffer from significant microstructure evolution via dislocation-boundary interactions during plastic deformation even at room temperature. Manipulation of grain boundary structures/properties via dopants segregation at grain boundaries to inhibit grain coalescence associated with remarkably enhanced mechanical properties is then discussed in three representative binary Cu-based systems, id est, Cu-Zr, Cu-Al, and Cu-W. This is finally followed by a summary of this chapter.
Download or read book Grain Boundary Influence on Radiation Induced Defect Evolution in Nanocrystalline Metals written by James Nathaniel (II) and published by . This book was released on 2019 with total page 175 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of materials that can better withstand the operating environment within nuclear reactors is of critical importance for the longevity of existing and the robustness of future nuclear energy systems. It is conjectured that nanocrystalline materials should exhibit significant reductions in radiation damage, however despite extensive studies, fundamental questions remain regarding defect evolution and migration to grain boundaries. Specifically, the role of grain size and grain boundary properties must be understood to develop insights into how to create new material microstructures that have enhanced radiation tolerance. The work presented makes use of in situ and ex situ experimental approaches to examine the role of grain size and grain boundary character in response to radiation damage in model FCC metals. Heavy ion irradiation experiments were carried out on metal foils under varying experimental conditions followed by post-irradiation analysis of grains ranging from 10 nm to 200 nm in size. Transmission electron microscopy (TEM) and related techniques were used to evaluate defect densities (dislocations and cavities) and defect cluster size as a function of grain size and grain boundary misorientation. Phenomena related to grain boundary response to damage absorption and sink efficiency are examined as well. The goal of this work is to contribute to building a fundamental framework for microstructural design to fabricate more radiation tolerant materials.
Download or read book A Monte Carlo Potts Investigation of Microstructural Evolution written by Corentin Alain Pierre Nicolas Guebels and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The microstructural changes that occur in metals and alloys due to deformation and heat treatment are often characterized according to the macroscale deformation process (i.e. cold or hot working). The general problem of this type of characterization is that it only distinguishes the general microstructural trends. For many decades, these microstructural phenomena have been described empirically or with limited experimental verification. This shortcoming is apparent for recrystallization and abnormal grain growth processes. Understanding and characterizing the thermal and mechanical processes that compete to control grain boundary kinetics and the subsequent microstructural evolution is critical. These include but are not limited to: the input and recovery of deformation energy, the influence of deformation energy on grain boundary migration, the mechanisms controlling the nucleation of new grains, and the effect of second-phase particles. The present work introduces a new temporal scaling method and investigates the conditions in which some grain boundaries may become unpinned in an otherwise stable, pinned microstructure and extends work done by E. Holm. The temporal scaling method contributes to resolving some of the limitations of Monte Carlo Potts (MCP) simulations in the investigation of the conditions and mechanisms that distinguish recrystallization from dynamic abnormal grain growth (DAGG). Grain boundary unpinning is then investigated for the case of an idealized spherical grain and for a polycrystalline microstructure. The mechanisms of grain boundary pinning and grain growth inhibition by second-phase particles are well known. The influence of simulation temperature on grain boundary unpinning is investigated numerically using a 3D Monte Carlo Potts approach. MCP based models are commonly implemented to simulate microstructural evolution. However, the numerical implementations of recrystallization and other deformation-induced phenomena often elude validation due to the lack of a common temporal scale. The numerical models for recovery, nucleation and recrystallization must be analyzed and verified in order to identify the conditions that initiate or the mechanisms driving DAGG. The temporal scaling method proposed in this work approaches this issue by identifying a time-energy relationship during normal grain growth simulations. This energy-based relationship creates the temporal scale for subsequent simulations of grain boundary migration during deformation. The applicability of this temporal scaling approach is investigated by considering a simple static recrystallization model. The present investigation predicts that the probability of grain boundaries becoming unpinned as a result of thermally-activated microstructural fluctuations increases with temperature while the characteristic time for unpinning to occur decreases. If the probability of grain boundary unpinning is relatively low and the characteristic time for unpinning to occur is not too large, it is possible for a single grain to become unpinned and grow to overtake the microstructure; this is particle assisted abnormal grain growth (PAAGG). The critical values of simulation temperature for the occurrence of PAAGG at prescribed particle volume fractions are characterized.
Download or read book Handbook of Mechanics of Materials written by Siegfried Schmauder and published by Springer. This book was released on 2019-05-09 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive reference for the studies of mechanical properties of materials over multiple length and time scales. The topics include nanomechanics, micromechanics, continuum mechanics, mechanical property measurements, and materials design. The handbook employs a consistent and systematic approach offering readers a user friendly reference ideal for frequent consultation. It is appropriate for an audience at of graduate students, faculties, researchers, and professionals in the fields of Materials Science, Mechanical Engineering, Civil Engineering, Engineering Mechanics, and Aerospace Engineering.
Download or read book Quantification of Grain Boundary Mediated Plasticity Mechanisms in Nanocrystalline Metals written by Jason F. Panzarino and published by . This book was released on 2016 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanocrystalline metals have been a topic of great discussion over recent years due to their exceptional strengths and novel grain boundary-mediated deformation mechanisms. Their microstructures are known to evolve through dynamic processes such as grain boundary migration and grain rotation, but how the collective interaction of these mechanisms alter the microstructure on a larger scale is not completely understood. In this thesis, we present coupled atomistic modeling and experimental tasks that aim to understand how the grain structure, grain boundaries, and associated grain boundary network change during nanocrystalline plasticity. Due to the complex three-dimensional nature of these mechanisms and the limited spatial and temporal resolution of current in-situ experimental techniques, we turn to atomistic modeling to help understand the dynamics by which these mechanisms unfold. In order to provide a quantitative analysis of this behavior, we develop a tool which fully characterizes nanocrystalline microstructures in atomistic models and subsequently tracks their evolution during molecular dynamics simulations. We then use this algorithm to quantitatively track grain structure and boundary network evolution in plastically deformed nanocrystalline Al, finding that higher testing temperature and smaller average grain size results in increased evolution of grain structure with evidence of larger scale changes to the grain boundary network also taking place. This prompts us to extend our analysis technique to include full characterization of grain boundary networks and rigorous topographical feature identification. We then employ this tool on simulations of Al subject to monotonic tension, cycling loading, and simple annealing, and find that each case results in different evolution of the grain boundary network. Finally, our computational work is complemented synergistically by experimental analyses which track surface microstructure evolution during sliding wear of nanocrystalline Ni-W thin films. These experiments track the development of a surface grain growth layer which evolves through grain boundary mediated plasticity and we are able to make direct connections between this evolution and that which was observed in our simulation work. All of the findings of this thesis are a direct result of the dynamic and collective nature by which nanocrystalline materials deform.
Download or read book Grain Boundary Segregation in Metals written by Pavel Lejcek and published by Springer Science & Business Media. This book was released on 2010-07-20 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: Grain boundaries are important structural components of polycrystalline materials used in the vast majority of technical applications. Because grain boundaries form a continuous network throughout such materials, their properties may limit their practical use. One of the serious phenomena which evoke these limitations is the grain boundary segregation of impurities. It results in the loss of grain boundary cohesion and consequently, in brittle fracture of the materials. The current book deals with fundamentals of grain boundary segregation in metallic materials and its relationship to the grain boundary structure, classification and other materials properties.
Download or read book Grain Boundary Effects on Microstructural Stability of Nanocrystalline Metallic Materials written by Xiaofei Zhu and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Grain boundaries play an important role in dictating the mechanical and physical properties of nanocrystalline (NC) materials because of the increased volume fraction of intercrystalline components as the grain size decreases. In general, grain boundaries have a high energy level and there exists a thermodynamic driving force to reduce the overall area of grain boundaries through grain coarsening, making NC material systems intrinsically unstable. Recent investigations also indicate that mechanical deformation can promote grain growth in NC material even at the cryogenic temperatures. In this chapter, first, the current investigation on the grain boundary structures of NC metallic materials is briefly reviewed and then the state-of-the-art of experimental results on the microstructural stability during deformation processes is discussed. Finally, several key issues for improving the microstructure stability of NC metallic materials and possible future work are discussed.
Download or read book Influence of Grain Misorientation on Grain Growth in Nanocrystalline Metals written by Justin Glen Brons and published by . This book was released on 2013 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is well known that the grain size of a material controls its properties, including mechanical strength, electrical conduction, and corrosion resistance. Typically, a fine grain size is desirable, since it allows for these properties to be increased. Nanocrystalline materials have been engineered in order to maximize the benefits associated with this fine grain size. Unfortunately, the high density of grain boundaries for a given volume of the material leads to an increase in the excess energy that is associated with grain boundaries. This excess energy can act as a driving force for grain growth, which causes these nanocrystalline structures to be unstable, with this grain growth often times being detrimental to the material properties. This research investigated the influence of grain boundary mobility and the applied driving force on grain growth in nanocrystalline metal films by focusing on the role grain boundary misorientation plays in regulating grain growth. The was be accomplished by completing two types of studies: (i) Annealing sputter-deposited thin films to study mobility in a case where the driving force is assumed to be dominated by grain boundary curvature and (ii) Mechanically indenting thin films with different microstructural features while submerged in liquid nitrogen. In terms of the latter study, the mobility was expected to be extremely low due to the cryogenic temperatures. Both sets of films were then characterized using precession-enhanced diffraction-based orientation analysis in the transmission electron microscope to quantify the evolution in grain size, grain morphology, and in the grain-to-grain misorientation.
Download or read book Modeling Materials written by Ellad B. Tadmor and published by Cambridge University Press. This book was released on 2011-11-24 with total page 789 pages. Available in PDF, EPUB and Kindle. Book excerpt: Material properties emerge from phenomena on scales ranging from Angstroms to millimeters, and only a multiscale treatment can provide a complete understanding. Materials researchers must therefore understand fundamental concepts and techniques from different fields, and these are presented in a comprehensive and integrated fashion for the first time in this book. Incorporating continuum mechanics, quantum mechanics, statistical mechanics, atomistic simulations and multiscale techniques, the book explains many of the key theoretical ideas behind multiscale modeling. Classical topics are blended with new techniques to demonstrate the connections between different fields and highlight current research trends. Example applications drawn from modern research on the thermo-mechanical properties of crystalline solids are used as a unifying focus throughout the text. Together with its companion book, Continuum Mechanics and Thermodynamics (Cambridge University Press, 2011), this work presents the complete fundamentals of materials modeling for graduate students and researchers in physics, materials science, chemistry and engineering.
Download or read book Mechanical Behavior of Materials written by Marc A. Meyers and published by . This book was released on 2008 with total page 856 pages. Available in PDF, EPUB and Kindle. Book excerpt: Includes numerous examples and problems for student practice, this textbook is ideal for courses on the mechanical behaviour of materials taught in departments of mechanical engineering and materials science.
Download or read book Transmission Electron Microscopy written by C. Barry Carter and published by Springer. This book was released on 2016-08-24 with total page 543 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text is a companion volume to Transmission Electron Microscopy: A Textbook for Materials Science by Williams and Carter. The aim is to extend the discussion of certain topics that are either rapidly changing at this time or that would benefit from more detailed discussion than space allowed in the primary text. World-renowned researchers have contributed chapters in their area of expertise, and the editors have carefully prepared these chapters to provide a uniform tone and treatment for this exciting material. The book features an unparalleled collection of color figures showcasing the quality and variety of chemical data that can be obtained from today’s instruments, as well as key pitfalls to avoid. As with the previous TEM text, each chapter contains two sets of questions, one for self assessment and a second more suitable for homework assignments. Throughout the book, the style follows that of Williams & Carter even when the subject matter becomes challenging—the aim is always to make the topic understandable by first-year graduate students and others who are working in the field of Materials Science Topics covered include sources, in-situ experiments, electron diffraction, Digital Micrograph, waves and holography, focal-series reconstruction and direct methods, STEM and tomography, energy-filtered TEM (EFTEM) imaging, and spectrum imaging. The range and depth of material makes this companion volume essential reading for the budding microscopist and a key reference for practicing researchers using these and related techniques.
Download or read book Crystal Plasticity Finite Element Methods written by Franz Roters and published by John Wiley & Sons. This book was released on 2011-08-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by the leading experts in computational materials science, this handy reference concisely reviews the most important aspects of plasticity modeling: constitutive laws, phase transformations, texture methods, continuum approaches and damage mechanisms. As a result, it provides the knowledge needed to avoid failures in critical systems udner mechanical load. With its various application examples to micro- and macrostructure mechanics, this is an invaluable resource for mechanical engineers as well as for researchers wanting to improve on this method and extend its outreach.
Download or read book Grain Boundary Structure and Properties written by Geoffrey Allan Chadwick and published by . This book was released on 1976 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Understanding the Mechanistic Role of Grain Boundaries on the Strength and Deformation of Nanocrystalline Metals Using Atomistic Simulations written by Satish Rajaram and published by . This book was released on 2019 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanocrystalline (NC) materials, defined structurally by having average grain sizes less than 100nm, exhibit a number of enhanced mechanical properties such as ultrahigh strength, improved wear resistance and greater resistance to fatigue crack initiation compared to coarser grained polycrystalline (PC) materials. NC materials exhibit these improved properties, in part, due to the increased grain boundary (GB) volume fraction. NC materials strength increases with decreasing grain size, known as the Hall-Petch (HP) effect often resulting in a peak strength between 10-20nm. Studies have shown that NC materials strength decreases due to the shift from dislocation-dominant to GB-dominant deformation mechanisms in the plastic flow regime as average grain size decreases below 10-20nm. While the potential improved properties are of interest, the application of NC materials are hindered due to microstructural instability i.e., grain growth to reduce the total energy of the system, thus degrading desired mechanical properties. Numerous studies have looked at avenues to stabilize NC microstructure, namely through thermodynamics and kinetics, alloying has been one significant strategy used to stabilize NC materials. As these processes are used to stabilize NC microstructures to thermally-induce grain growth, they add additional uncertainty as the deformation and GB behavior of pure NC materials are still not fully understood. Experimental work on NC materials is difficult due to the length scale being investigated as it is difficult to manufacture and can be time consuming to analyze with current technology. Atomistic simulations have shown the potential to investigate fundamental behavior at the nanoscale and provide important insight in the mechanisms that drive the mechanical behavior of NC materials. This thesis will use atomistic simulations to study the structure-property relationship of face-centered-cubic (fcc) metals by focusing on GBs to investigate the strength of NC nickel. During the course of this thesis, four aspects that govern NC behavior will be studied, yielding, plasticity, thermal effects, and GB disorder to elucidate deeper insight into the underlying deformation mechanisms that control the strength of FCC NC metals i.e., flow stress, in the grain size regime 6 to 20nm.
Download or read book 2D and 3D Grain Growth Modeling and Simulation written by Luis Antonio Barrales-Mora and published by Cuvillier Verlag. This book was released on 2008 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermally Activated Mechanisms in Crystal Plasticity written by D. Caillard and published by Elsevier. This book was released on 2003-09-08 with total page 453 pages. Available in PDF, EPUB and Kindle. Book excerpt: KEY FEATURES: - A unified, fundamental and quantitative resource. The result of 5 years of investigation from researchers around the world - New data from a range of new techniques, including synchrotron radiation X-ray topography provide safer and surer methods of identifying deformation mechanisms - Informing the future direction of research in intermediate and high temperature processes by providing original treatment of dislocation climb DESCRIPTION: Thermally Activated Mechanisms in Crystal Plasticity is a unified, quantitative and fundamental resource for material scientists investigating the strength of metallic materials of various structures at extreme temperatures. Crystal plasticity is usually controlled by a limited number of elementary dislocation mechanisms, even in complex structures. Those which determine dislocation mobility and how it changes under the influence of stress and temperature are of key importance for understanding and predicting the strength of materials. The authors describe in a consistent way a variety of thermally activated microscopic mechanisms of dislocation mobility in a range of crystals. The principles of the mechanisms and equations of dislocation motion are revisited and new ones are proposed. These describe mostly friction forces on dislocations such as the lattice resistance to glide or those due to sessile cores, as well as dislocation cross-slip and climb. They are critically assessed by comparison with the best available experimental results of microstructural characterization, in situ straining experiments under an electron or a synchrotron beam, as well as accurate transient mechanical tests such as stress relaxation experiments. Some recent attempts at atomistic modeling of dislocation cores under stress and temperature are also considered since they offer a complementary description of core transformations and associated energy barriers. In addition to offering guidance and assistance for further experimentation, the book indicates new ways to extend the body of data in particular areas such as lattice resistance to glide.
