Download or read book In situ Visualization and Quantification of Polymer Crystallization Under Complex Flows During Foam Extrusion Processing written by Alireza Tabatabaei Naeini and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The crystallization behavior of polypropylene (PP) and poly(lactic acid) (PLA) during foam extrusion processing was investigated via visualization techniques. In the experiments, a tandem extrusion system equipped with a conical converging flow channel and a high temperature/pressure visualization chamber were employed. Using the developed system, effect of processing parameters on crystallization was elucidated. These parameters included the processing temperature, the carbon dioxide content, the flow rate, and the strain rate. The visualized crystallites were quantified based on their light intensities and by the definition of the Crystallinity Index (CI) and the Crystallite Size (CS), where the CI and CS corresponded to the relative crystallinity and the size of crystallites, respectively. Moreover, a correlation was made between the content of the induced crystallites inside the extruder and the cellular structure of the extruded foams. It was verified by visualization that both PP and PLA crystallize during the process even at a temperature above their nominal melting peak point (Tm). The formation of crystallites at a temperature above the Tm was asserted to the strain-induced crystallization. Moreover, a procedure was proposed in order to decouple the effect of the flow rate (corresponded to the strain rate) and the cooling history. A significant enhancement in crystallization kinetics was observed by increasing the strain rate. This crystallization enhancement caused by the increased flow rate became more pronounced at lower temperatures, most probably due to the higher degree of molecular orientation. Adding the CO2 shifted the crystallization temperature to a lower processing temperature due to its plasticization effect, but it accelerated the crystallization kinetics. This clearly explained the decrease in the optimal processing temperature for foaming with an increased CO2 content. It was also confirmed that the induced crystallites during the process had a great effect on the cellular morphology of the resultant foam product.
Download or read book Visualization of the Crystallization in Foam Extrusion Process written by Alireza Tabatabaei Naeini and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Polymers Abstracts written by and published by . This book was released on 1996 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Polymeric Foams written by Shau-Tarng Lee and published by CRC Press. This book was released on 2016-11-03 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polymeric foams are sturdy yet lightweight materials with applications across a variety of industries, from packaging to aerospace. As demand for these materials increase, so does innovation in the development of new processes and products. This book captures the most dynamic advances in processes, technologies, and products related to the polymeric foam market. It describes the latest business trends including new microcellular commercialization, sustainable foam products, and nanofoams. It also discusses novel processes, new and environmentally friendly blowing agents, and the development and usage of various types of foams, including bead and polycarbonate, polypropylene, polyetherimide microcellular, and nanocellular. The book also covers flame-retardant foams, rigid foam composites, and foam sandwich composites and details applications in structural engineering, electronics, and insulation. Authored by leading experts in the field, this book minimizes the gap between research and application in this important and growing area.
Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2668 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Poly lactic acid written by Rafael A. Auras and published by Wiley. This book was released on 2010-10-19 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the synthesis, properties, and processing methods of poly(lactic acid) (PLA), an important family of degradable plastics. As the need for environmentally-friendly packaging materials increases, consumers and companies are in search for new materials that are largely produced from renewable resources, and are recyclable. To that end, an overall theme of the book is the biodegradability, recycling, and sustainability benefits of PLA. The chapters, from a base of international expert contributors, describe specific processing methods, spectroscopy techniques for PLA analysis, and and applications in medical items, packaging, and environmental use.
Download or read book Characterization of Polymer Blends written by Sabu Thomas and published by John Wiley & Sons. This book was released on 2015-02-09 with total page 972 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filling the gap for a reference dedicated to the characterization of polymer blends and their micro and nano morphologies, this book provides comprehensive, systematic coverage in a one-stop, two-volume resource for all those working in the field. Leading researchers from industry and academia, as well as from government and private research institutions around the world summarize recent technical advances in chapters devoted to their individual contributions. In so doing, they examine a wide range of modern characterization techniques, from microscopy and spectroscopy to diffraction, thermal analysis, rheology, mechanical measurements and chromatography. These methods are compared with each other to assist in determining the best solution for both fundamental and applied problems, paying attention to the characterization of nanoscale miscibility and interfaces, both in blends involving copolymers and in immiscible blends. The thermodynamics, miscibility, phase separation, morphology and interfaces in polymer blends are also discussed in light of new insights involving the nanoscopic scale. Finally, the authors detail the processing-morphology-property relationships of polymer blends, as well as the influence of processing on the generation of micro and nano morphologies, and the dependence of these morphologies on the properties of blends. Hot topics such as compatibilization through nanoparticles, miscibility of new biopolymers and nanoscale investigations of interfaces in blends are also addressed. With its application-oriented approach, handpicked selection of topics and expert contributors, this is an outstanding survey for anyone involved in the field of polymer blends for advanced technologies.
Download or read book Polymer Based Additive Manufacturing written by Jonathan E. Seppala and published by . This book was released on 2020-08-25 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Additive manufacturing (AM) is a potentially disruptive technology, revolutionizing not only traditional industries but generating entirely new ones through rapid innovation, the democratization of manufacturing, and unprecedented freedom of design. Furthermore, the development of AM technologies has practical implications for economic growth, healthcare, national security, space exploration, and sustainability. For military and space agencies, AM offers the possibility to transform the traditional supply chain system through manufacturing at-point-of-demand, recycling, and indigenous sourcing of raw materials. Similarly, these concepts are being leveraged by remote communities across the globe through efforts such as Fab Labs, which provide low-cost access to manufacturing technologies. AM is transforming healthcare in unexpected ways: doctors and patients have access to high-quality physical 3D models generated directly from computerized tomography (CT) scans. These surgical guides have proved invaluable in surgical preparation and patient consent. In the lab, researchers are developing medical devices or implants which mimic the patient's physiology, are pre-loaded with therapeutics, and are replaced with the patient's cells through natural tissue repair pathways. Pushing the limits of resolution, multi-photon technologies, which allow subdiffraction-limited resolution, are revolutionizing the development of micro-optical components. Unfortunately, adoption of AM technologies by industry has been slow; and while there are numerous success stories and commercial adoption is steadily increasing, AM is hampered by weak parts, incomplete certification methods, and empirical materials development. Regulatory and standards bodies are working to update or develop new standards and policies to deal with the unique material and production issues posed by AM. Many of the challenges facing the industry stem from our limited understanding of structure-process-performance relationships. These challenges fall into many categories and require a broad range of skills to address. For the researcher, AM processes offer unique challenges in materials development, metrology, and modeling, as well as opportunities to combine all three. What makes a polymer printable? What process parameters are important? How should parts be tested? These are all active areas of investigation. This book was inspired by the 2017 ACS Symposium "Additive Manufacturing of Structures and Functional Devices: Materials, Methods, Models, and Testing" and is supplemented by additional experts in the polymer AM field. The chapters discuss the technologies, measurement challenges, manufacturing opportunities, and fabrication potentials. We begin with an introduction to polymer additive manufacturing, identifying the measurement needs and technical challenges facing the industry. A chapter reviewing polymer powder bed fusion follows, providing a complete discussion on methods, materials, and applications. The bulk of the book covers thermoplastic material extrusion, with chapters discussing recycling-based feedstocks, composites materials, and multi-physics modeling linking experimentation and theory. Moving from thermoplastics to conductive inks, a chapter on in situ monitoring and control of direct-ink-write provides a clear example of how theory and modern machine vision can be used to create a practical and responsive control system. The last chapter provides a state-of-the-art review of multi-photon printing, discussing methods, materials, and the stunning capabilities of the technique"--
Download or read book Thermoplastic Foam Processing written by Richard Gendron and published by CRC Press. This book was released on 2004-10-28 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: As researchers seek replacements for banned, ozone-depleting foaming agents, the authors of Thermoplastic Foam Processing: Principles and Development strive to develop a better understanding of foaming processes and find solutions for day-to-day practice. This book presents the latest research in foam extrusion and physical foaming agents with a st
Download or read book Polymer layered Silicate Nanocomposites written by Masami Okamoto and published by iSmithers Rapra Publishing. This book was released on 2003 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: The review sets out to highlight the major developments in this field over the last decade. The different techniques used to prepare PLS nanocomposites are covered. The physicochemical characterisation of PLS nanocomposites and the improved materials properties that those materials can display are discussed. An additional indexed section containing several hundred abstracts from the Rapra Polymer Library database provides useful references for further reading.
Download or read book UHMWPE Biomaterials Handbook written by Steven M. Kurtz and published by Academic Press. This book was released on 2009-04-27 with total page 564 pages. Available in PDF, EPUB and Kindle. Book excerpt: UHMWPE Biomaterials Handbook describes the science, development, properties and application of of ultra-high molecular weight polyethylene (UHMWPE) used in artificial joints. This material is currently used in 1.4 million patients around the world every year for use in the hip, knee, upper extremities, and spine. Since the publication of the 1st edition there have been major advances in the development and clinical adoption of highly crosslinked UHMWPE for hip and knee replacement. There has also been a major international effort to introduce Vitamin E stabilized UHMWPE for patients. The accumulated knowledge on these two classes of materials are a key feature of the 2nd edition, along with an additional 19 additional chapters providing coverage of the key engineering aspects (biomechanical and materials science) and clinical/biological performance of UHMWPE, providing a more complete reference for industrial and academic materials specialists, and for surgeons and clinicians who require an understanding of the biomaterials properties of UHMWPE to work successfully on patient applications. The UHMWPE Handbook is the comprehensive reference for professionals, researchers, and clinicians working with biomaterials technologies for joint replacement New to this edition: 19 new chapters keep readers up to date with this fast moving topic, including a new section on UHMWPE biomaterials; highly crosslinked UHMWPE for hip and knee replacement; Vitamin E stabilized UHMWPE for patients; clinical performance, tribology an biologic interaction of UHMWPE State-of-the-art coverage of UHMWPE technology, orthopedic applications, biomaterial characterisation and engineering aspects from recognised leaders in the field
Download or read book Polymer Colloids written by Rodney Priestley and published by Royal Society of Chemistry. This book was released on 2019-12-02 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Academic and industrial research around polymer-based colloids is huge, driven both by the development of mature technologies, e.g. latexes for coatings, as well as the advancement of new materials and applications, such as building blocks for 2D/3D structures and medicine. Edited by two world-renowned leaders in polymer science and engineering, this is a fundamental text for the field. Based on a specialised course by the editors, this book provides the reader with an invaluable single source of reference. The first section describes formation, explaining basic properties of emulsions and dispersion polymerization, microfluidic approaches to produce polymer-based colloids and formation via directed self-assembly. The next section details characterisation methodologies from microscopy and small angle scattering, to surface science and simulations. The final chapters close with applications, including Pickering emulsions and molecular engineering for materials development. A comprehensive guide to polymer colloids, with contributions by leaders in their respective areas, this book is a must-have for researchers and practitioners working across polymers, soft matter and chemical and molecular engineering.
Download or read book Polymeric Foams written by Shau-Tarng Lee and published by CRC Press. This book was released on 2006-08-21 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polymers are among the major hallmarks of 20th-century science, and the explosive outgrowth and tremendous importance of polymeric foams is a testament to their amazing versatility and unique properties. With applications from automotive to acoustic and medical, polymeric foams pervade all areas of our lives. If this growth is to continue into the
Download or read book Injectable Biomaterials written by Brent Vernon and published by Elsevier. This book was released on 2011-01-24 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: Novel injectable materials for non-invasive surgical procedures are becoming increasingly popular. An advantage of these materials include easy deliverability into the body, however the suitability of their mechanical properties must also be carefully considered. Injectable biomaterials covers the materials, properties and biomedical applications of injectable materials, as well as novel developments in the technology.Part one focuses on materials and properties, with chapters covering the design of injectable biomaterials as well as their rheological properties and the mechanical properties of injectable polymers and composites. Part two covers the clinical applications of injectable biomaterials, including chapters on drug delivery, tissue engineering and orthopaedic applications as well as injectable materials for gene delivery systems. In part three, existing and developing technologies are discussed. Chapters in this part cover such topics as environmentally responsive biomaterials, injectable nanotechnology, injectable biodegradable materials and biocompatibility. There are also chapters focusing on troubleshooting and potential future applications of injectable biomaterials.With its distinguished editor and international team of contributors, Injectable biomaterials is a standard reference for materials scientists and researchers working in the biomaterials industry, as well as those with an academic interest in the subject. It will also be beneficial to clinicians. Comprehensively examines the materials, properties and biomedical applications of injectable materials, as well as novel developments in the technology Reviews the design of injectable biomaterials as well as their rheological properties and the mechanical properties of injectable polymers and composites Explores clinical applications of injectable biomaterials, including drug delivery, tissue engineering, orthopaedic applications and injectable materials for gene delivery systems
Download or read book Process Intensification written by David Reay and published by Butterworth-Heinemann. This book was released on 2013-06-05 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Intensification: Engineering for Efficiency, Sustainability and Flexibility is the first book to provide a practical working guide to understanding process intensification (PI) and developing successful PI solutions and applications in chemical process, civil, environmental, energy, pharmaceutical, biological, and biochemical systems. Process intensification is a chemical and process design approach that leads to substantially smaller, cleaner, safer, and more energy efficient process technology. It improves process flexibility, product quality, speed to market and inherent safety, with a reduced environmental footprint. This book represents a valuable resource for engineers working with leading-edge process technologies, and those involved research and development of chemical, process, environmental, pharmaceutical, and bioscience systems. No other reference covers both the technology and application of PI, addressing fundamentals, industry applications, and including a development and implementation guide Covers hot and high growth topics, including emission prevention, sustainable design, and pinch analysis World-class authors: Colin Ramshaw pioneered PI at ICI and is widely credited as the father of the technology
Download or read book Hot Embossing written by Matthias Worgull and published by William Andrew. This book was released on 2009-09-28 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is an overview of replication technology for micro- and nanostructures, focusing on the techniques and technology of hot embossing, a scaleable and multi-purpose technology for the manufacture of devices such as BioMEMS and microfluidic devices which are expected to revolutionize a wide range of medical and industrial processes over the coming decade.The hot embossing process for replicating microstructures was developed by the Forschungszentrum Karlsruhe (Karlsruhe Institute of Technology) where the author is head of the Nanoreplication Group. Worgull fills a gap in existing information by fully detailing the technology and techniques of hot embossing. He also covers nanoimprinting, a process related to hot embossing, with examples of actual research topics and new applications in nanoreplication. A practical and theoretical guide to selecting the materials, machinery and processes involved in microreplication using hot embossing techniques Compares different replication processes such as: micro injection molding, micro thermoforming, micro hot embossing, and nanoimprinting Details commercially available hot embossing machinery and components like tools and mold inserts
Download or read book Rubber Toughened Engineering Plastics written by A.A. Collyer and published by Springer Science & Business Media. This book was released on 1994-05-31 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rubber Toughened Engineering Plastics covers the main physical principles involved in optimum toughening in high temperature engineering plastics and speciality plastics and describes the synthetic strategies used to obtain satisfactorily toughened grades in these materials by control of microstructure. This book will act as a focus for current thought on the principles of rubber toughening and the methods employed for the rubber toughening of major engineering and speciality plastics.
