Download or read book Improvement of Fracture Conductivity Through Study of Proppant Transport and Chemical Stimulation written by Songyang Tong and published by . This book was released on 2019 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: During hydraulic fracturing treatments, proppants – usually sand – are placed inside fractures to improve fracture conductivity. However, a large portion of the generated hydraulic fractures often remain unpropped after fracturing treatments. There are two primary reasons for this poor proppant placement. First, proppants settle quickly in common fracturing fluids (e.g., slickwater), which results in unpropped sections at the tip or top of the fracture. Second, a large number of the microfractures are too narrow to accommodate any common commercial proppant. Such unpropped fractures hold a large potential flow capacity as they exhibit a large contact area with the reservoir. However, their potential flow capacity is diminished during production due to closing of unpropped fractures because of closure stress. In this study, fractures are categorized as wider fractures, which are accessible to proppant, and narrower fractures, which are inaccessible to proppant. For wider fractures, proppant transport is important as proppant is needed for keeping them open. For narrower fractures, a chemical formulation is proposed as there is less physical restriction for fluids to flow inside across them. The chemical formulation is expected to improve fracture conductivity by generating roughness on fracture surfaces. This dissertation uses experiments and simulations to investigate proppant transport in a complex fracture network with laboratory-scale transparent fracture slots. Proppant size, injection flow rate and bypass fracture angle are varied and their effects are systematically evaluated. Based on experimental results, a straight-line relationship can be used to quantify the fraction of proppant that flows into bypass fractures with the total amount of proppant injected. A Computational Fluid Dynamics (CFD) model is developed to simulate the experiments; both qualitative and quantitative matches are achieved with this model. It is concluded that the fraction of proppant which flows into bypass fractures could be small unless a significant amount of proppant is injected, which indicates the inefficiency of slickwater in transporting proppant. An alternative fracturing fluid – foam – has been proposed to improve proppant placement because of its proppant carrying capacity. Foam is not a single-phase fluid, and it suffers liquid drainage with time due to gravity. Additionally, the existence of foam bubbles and lamellae could alter the movement of proppants. Experiments and simulations are performed to evaluate proppant placement in field-scale foam fracturing application. A liquid drainage model and a proppant settling correlation are developed and incorporated into an in-housing fracturing simulator. Results indicate that liquid drainage could negatively affect proppant placement, while dry foams could lead to negligible proppant settling and consequently uniform proppant placement. For narrower fractures, two chemical stimulation techniques are proposed to improve fracture conductivity by increasing fracture surface roughness. The first is a nanoparticle-microencapsulated acid (MEA) system for shale acidizing applications, and the second is a new technology which can generate mineral crystals on the shale surface to act as in-situ proppants. The MEA could be released as the fracture closes and the released acid could etch the surface of the rock locally, in a non-uniform way, to improve fracture conductivity (up to 40 times). Furthermore, the in-situ proppant generation technology can lead to crystal growth in both fracking water and formation brine conditions, and it also improves fracture conductivity (up to 10 times) based on core flooding experiments

Download or read book Integrated 3 dimensional Modeling of Proppant Transport Through Hydraulic Fracture Network in Shale Gas Reservoir written by Oliver Chang and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic fracturing is one of the most successful and widely applied techniques that ensure economic recovery from unconventional reservoirs. Oil and gas bearing formation has pre-existing natural fractures and possesses a large proportion in hydrocarbon resources. Distinct fracture propagational behavior and operational variation both affect the entire hydraulic fracturing treatment. Proppant transport and fracture network conductivity are the most significant factors determining the effectiveness of a treatment. The concept of stimulated reservoir volume (SRV) is used to characterize the efficiency of hydraulic fracturing treatment. However, the unpropped fracture will close after the well starts to produce without contributing hydrocarbon recovery. Only the propped open section of fracture contributes to the hydrocarbon recovery. Therefore, the concept of propped open stimulated reservoir volume (PSRV) is proposed to characterize the effectiveness of the treatment. Physics of proppant transport in a complex fracture network is unclear to the engineers. Most of the model simulates using simplified physics. In this work, we first identified the patterns of proppant transport and we developed equations to quantify the governing physics in each pattern, in order to capture the proppant transport process accurately. To quantify the PSRV, a dynamic 3-D, finite-difference, proppant transport model is developed and linked to a hydraulic fracture propagation model to simulate the process of proppant transport through the hydraulic fracture network. The actual propped open stimulated reservoir volume (PSRV) and fracture network conductivity can be quantified by utilizing the model. The goal of this study is to generate guidelines to maximize the effectiveness of the hydraulic fracturing treatment. Hence, a systematic parametric study was conducted to investigate the relation among engineering factors, geomechanical and reservoir properties. The effect of each parameter on PSRV, PSRV/SRV efficiency ratio, and average fracture conductivity during pressure pumping, flowback and shut-in is evaluate and quantified. Guidelines to optimize the effectiveness of hydraulic fracturing treatment for different scenarios are established based on the systematic parametric study.

Download or read book The Role of Acidizing in Proppant Fracturing in Carbonate Reservoirs written by Jurairat Densirimongkol and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Today, optimizing well stimulation techniques to obtain maximum return of investment is still a challenge. Hydraulic fracturing is a typical application to improve ultimate recovery from oil and gas reservoirs. Proppant fracturing has become one of the most widely considered alternatives for application in carbonate reservoirs. Especially in areas that have high closure stress, the non-smoothly etched surface created by acid fracturing may not remain open upon closing, resulting in decrease in fracture conductivity and unsuccessful stimulation treatment. In early years, because of the increase in the success of proppant fracturing, proppant partial monolayer has been put forward as a method that helps generate the maximum fracture conductivity from proppant fracturing treatment. However, this method was not widely successful because of proppant crushing and proppant embedment problems that result in losing conductivity. The ability to transport propping agents in available fracturing fluid was also poor and resulted in difficulties and failures to obtain proppant partial monolayer placement. For carbonate formations, acid fracturing is another effective stimulation method. Simpler operation and lower cost made the technique attractive in the field with plenty of successful experiences. The heterogeneity feature of carbonate formation brings a challenge to create sufficient conductivity. In cases of high closure formation, fracture conductivity is hard to sustain. This factor limited the applications of acid fracturing sometimes. In this study, laboratory tests were carried out using low concentrations of ultralightweight proppant to obtain partial monolayer proppant. Because of low specific gravity property of this proppant, it was claimed to help improve proppant transport inside the fracture. In this experimental study, the partial monolayer technique was examined with particular emphasis upon the impact of acid in possibly improving fracture conductivity of carbonate rocks. The technique is referred as "closed fracture acidizing". After obtaining a partial monolayer distribution on the fracture face, gelled acid was injected through the fracture face. Fracture conductivity before and after acid injection were evaluated. Experimental results showed clearly that acid injection does not enhance fracture conductivity of partial monolayer proppant fracturing. The more the volume of acid injection, the more rapidly fracture conductivity declines.

Download or read book Mathematical Theory of Oil and Gas Recovery written by P. Bedrikovetsky and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is a pleasure to be asked to write the foreword to this interesting new book. When Professor Bedrikovetsky first accepted my invitation to spend an extended sabbatical period in the Department of Mineral Resources Engineering at Imperial College of Science, Technology and Medicine, I hoped it would be a period of fruitful collaboration. This book, a short course and a variety of technical papers are tangible evidence of a successful stay in the UK. I am also pleased that Professor Bedrikovetsky acted on my suggestion to publish this book with Kluwer as part of the petroleum publications for which I am Series Editor. The book derives much of its origin from the unpublished Doctor of Science thesis which Professor Bedrikovetsky prepared in Russian while at the Gubkin Institute. The original DSc contained a number of discrete publications unified by an analytical mathematics approach to fluid flow in petroleum reservoirs. During his sabbatical stay at Imperial College, Professor Bedrikovetsky has refined and extended many of the chapters and has discussed each one with internationally recognised experts in the field. He received great encouragement and editorial advice from Dr Gren Rowan, who pioneered analytical methods in reservoir modelling at BP for many years.

Download or read book Shale Fracturing Enhancement by Using Polymer free Foams and Ultra light Weight Proppants written by Ming Gu and published by . This book was released on 2013 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt: Slickwater with sand is the most commonly used hydraulic fracturing treatment for shale reservoirs. The slickwater treatment produces long skinny fractures, but only the near wellbore region is propped due to fast settling of sand. Adding gel into water can prevent the fast settling of sand, but gel may damage the fracture surface and proppant pack. Moreover, current water-based fracturing consumes a large amount of water, has high water leakage, and imposes high water disposal costs. The goal of this project is to develop non-damaging, less water-intensive fracturing treatments for shale gas reservoirs with improved proppant placement efficiency. Earlier studies have proposed to replace sand with ultra-light weight proppants (ULWP) to enhance proppant transport, but it is not used commonly in field. This study evaluates the performance of three kinds of ULWPs covering a wide range of specific gravity and representing the three typical manufacturing methods. In addition to replacing sand with ULWPs, replacing water with foams can be an alternative treatment that reduces water usage and decreases proppant settling. Polymer-added foams have been used in conventional reservoirs to improve proppant placement efficiency. However, polymers can damage shale permeability in unconventional reservoirs. This dissertation studies polymer-free foams (PFF) and evaluates their performance. This study uses both experiments and simulations to assess the productivity and profitability of the ULWP treatment and PFF treatment. First, a reservoir simulation model is built in CMG to study the impact of fracture conductivity and propped length on fracture productivity. This model assumes a single fracture intersecting a few reactivated natural fractures. Second, a 2D fracturing model is used to simulate the fracture propagation and proppant transport. Third, strength, API conductivity and gravity settling rates are measured for three ULWPs. Fourth, foam stability tests are conducted to screen the best PFF agents and the selected foams are put into a circulating loop to study their rheology. Finally, empirical correlations from the experiments are applied in the fracturing model and reservoir model to predict productivity by using the ULWPs with slickwater or using the PFFs with sand. Experimental results suggest that, at 4000 psi with concentrations varying from partial monolayer (0.05 lb/ft2) to multilayer (1 lb/ft2), ULW-1 (polymeric) is the most deformable with conductivity of 1-10 md-ft. ULW-2 (resin coated and impregnated ground walnut hull) is the second most deformable with similar conductivity. ULW-3 (resin coated porous ceramic) is the least deformable with conductivity of 20-1000 md-ft, which is comparable to sand. Three foam formulations (A, B: regular surfactant foam, C: viscoelastic surfactant foam) are selected based on the stability results of fourteen surfactants. All PFFs exhibit power-law rheological behavior in a laminar flow regime. The power law parameters of the regular surfactant PFF depend on both quality and pressure when quality is higher than 60% but depend on quality only when quality is lower than 60%. Simulation results suggest that under the optimal concentration of 0.04-0.06 v/v (0.37-0.55 lb/gal) for both ULW-1 and ULW-2, and 0.1 v/v (1.46 lb/gal) for ULW-3, 1-year cumulative production for 0.1 [mu]D shale reservoir is higher than sand by 127% for ULW-1, 28% for ULW-2, and 38% for ULW-3. The productivity benefits decrease as shale permeability increases for all three ULWPs. ULW-1 and ULW-2 have higher productivity benefits for longer production time, while ULW-3 has relatively constant productivity benefits over time. The economic profit of ULW-1 when priced at $5/lb is 2.2 times larger than that of sand for 1-year production in 0.1 [mu]D shale reservoirs; the acceptable maximum price is $10/lb for ULW-1, $6/lb for ULW-2, and $2.5/lb for ULW-3. The maximum price increases as production time increases. The PFFs with a quality of 60% carrying mesh 40 sand at a partial monolayer concentration of 0.04 v/v (0.88 lb/gal) can generate 50% higher productivity, 74% higher economic profit, and over 300% higher water efficiency than the best slickwater-sand case (mesh 40 sand at 0.1 v/v) for 1-year production in 0.1[mu]D shale reservoirs. The benefits of using the PFFs decrease with increasing shale permeability, increasing production time, or decreasing pumping time. This dissertation gives a range of field conditions where the ULWP and PFF may be more effective than slickwater-sand fracturing.

Download or read book Investigating the Performance of High Viscosity Friction Reducers Used for Proppant Transport During Hydraulic Fracturing written by Mohammed Salem Ba Geri and published by . This book was released on 2019 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Over the last few recent years, high viscosity friction reducers (HVFRs) have been successfully used in the oil and gas industry across all premier shale plays in North America including Permian, Bakken, and Eagle Ford. However, selecting the most suitable fracture fluid system plays an essential role in proppant transport and minimizing or eliminating formation damage. This study investigates the influence of the use of produced water on the rheological behavior of HVFRs compared to a traditional linear guar gel. Experimental rheological characterization was studied to investigate the viscoelastic property of HVFRs on proppant transport. In addition, the successful implication of utilizing HVFRs in the Wolfcamp formation, in the Permian Basin was discussed. This study also provides a full comparative study of viscosity and elastic modulus between HVFRs and among fracturing fluids such as xanthan, polyacrylamide-based emulsion polymer, and guar. The research findings were analyzed to reach conclusions on how HVFRs can be an alternative fracture fluid system within many unconventional reservoirs. Compared to the traditional hydraulic fracture fluid system, the research shows the many potential advantages that HVFR fluids offer, including superior proppant transport capability, almost 100% retained conductivity, around 30% cost reduction, and logistics such as minimizing chemical usage by 50% and the ability to stoner operation equipment on location. Finally, this comprehensive investigation addresses up-to-date of using HVFRs challenges and emphasizes necessities for using HVFRs in high TDS fluids"--Abstract, page iv.

Download or read book Advances in Natural Gas Technology written by Hamid Al-Megren and published by BoD – Books on Demand. This book was released on 2012-04-11 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas is a vital component of the world's supply of energy and an important source of many bulk chemicals and speciality chemicals. It is one of the cleanest, safest, and most useful of all energy sources, and helps to meet the world's rising demand for cleaner energy into the future. However, exploring, producing and bringing gas to the user or converting gas into desired chemicals is a systematical engineering project, and every step requires thorough understanding of gas and the surrounding environment. Any advances in the process link could make a step change in gas industry. There have been increasing efforts in gas industry in recent years. With state-of-the-art contributions by leading experts in the field, this book addressed the technology advances in natural gas industry.

Download or read book Ultra Light Weight Proppants in Shale Gas Fracturing written by Abhishek Gaurav and published by . This book was released on 2010 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: The goal of the present work is to improve shale reservoir stimulation treatment by using ultra light weight proppants in fracturing fluids. Slickwater has become the most popular fracturing fluid for fracturing shales in recent times because it creates long and skinny fractures and it is relatively cheap. The problem with slickwater is the high rate of settling of common proppants, e.g. sand, which results in propped fractures which are much smaller than the original fractures. Use of gels can help in proppant transport but introduce large formation damage by blocking pores in nano-darcy shales. Gel trapping in the proppant pack causes reduction in permeability of the proppant pack. The light weight proppants which can easily be transported by slickwater and at the same time be able to provide enough fracture conductivity may solve this problem. Three ultra light weight proppants (ULW1, ULW2, and ULW3) have been studied. The mechanical properties of the proppant packs as well as single proppants have been measured. Conductivity of proppant packs has been determined as a function of proppant concentration and confining stress at an average Barnett shale temperature of 95°C. The crush strengths of all the three proppant packs are higher than typical stresses encountered (e.g., Barnett). ULW1 and ULW2 are highly deformable and do not produce many fines. ULW3 has a higher Young's modulus and produces fines. Conventionally, the proppant conductivity decreases with decreasing proppant concentration and increasing confining stress. But in cases of ULWs, for a partial monolayer, conductivity can be as large as that of a thick proppant pack. The settling velocity is the lowest for ULW1, intermediate for ULW2 and the highest for ULW3. This work contributes new mechanical, conductivity, and settling data on three ultra light weight proppants. Application of light weight proppants in stimulation treatments in shale reservoirs can lead to large propped fractures, which can improve the productivity of fractured shale reservoirs.

Download or read book Hydraulic Proppant Fracturing and Gravel Packing written by D. Mader and published by Elsevier. This book was released on 1989-03-01 with total page 1277 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many aspects of hydraulic proppant fracturing have changed since its innovation in 1947. The main significance of this book is its combination of technical and economical aspects to provide an integrated overview of the various applications of proppants in hydraulic fracturing, and gravel in sand control. The monitoring of fractures and gravel packs by well-logging and seismic techniques is also included.The book's extensive coverage of the subject should be of special interest to reservoir geologists and engineers, production engineers and technologists, and well log analysts.

Download or read book Effect of Fracture Heterogeneity on Proppant Transport and Settling Mechanism written by Dhurgham Abdulameer Kadhim and published by . This book was released on 2017 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Proppant transport modeling through fractures with slickwater fluid systems assumes uniform and homogeneous fracture widths by implying constant fluid behavior at wall boundaries. Hydraulic fracturing mineback operations have demonstrated that induced fractures are heterogeneous and varying in width. This work investigates the impact of fracture width heterogeneity, roughness, and leak-off on ceramic proppant transport and settling, using proppant distribution concepts of Equilibrium Dune Level (EDL) and equilibrium Dune Length (EDX). Experimental work was conducted to investigate the impact of fracture width heterogeneity by varying fracture width along two plexiglass sheets. To mimic actual hydraulic fractures, the injection side was designed as the largest width, and the width of the opposite end was reduced. The ratio between the injection and tip side widths was varied to study the effect of changing fracture width. One ratio was used as a base to study the effect of varying wall roughness and leak-off on the proppant placement. Results of this work demonstrate the impacts of reservoir heterogeneity, wall roughness, and leak off on proppant conveyance and distribution. Fracture width and wall roughness have a significant effect on proppant distribution along a fracture. Increasing width heterogeneity and roughness provide a better proppant distribution and thus better fracture propped conductivity. The effect of leak-off on proppant distribution was monitored, and it showed that proppant followed water movement. Consequently, average water volume that left the slot was affected by proppant distribution"--Abstract, page iii.

Download or read book Proppant Fracture Conductivity with High Proppant Loading and High Closure Stress written by Matthew Charles Rivers and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultra-deepwater reservoirs are important unconventional reservoirs that hold the potential to produce billions of barrels of hydrocarbons, but also present major challenges. This type of reservoir is usually high pressure and high temperature (HPHT) and has a relatively high permeability. Hydraulic fracturing high permeability reservoirs are different from the hydraulic fracturing technology used in low permeability formations. The main purpose of hydraulic fracturing in low permeability reservoirs is to create a long, highly conductive path, whereas in high permeability formations hydraulic fracturing is used predominantly to bypass near wellbore formation damage, control sand production and reduce near wellbore pressure drop. Hydraulically fracturing these types of wells requires short fractures packed with high proppant concentrations. In addition, fracturing in high permeability reservoirs aims at achieving enough fracture length to increase productivity, especially when the viscosity of the reservoir fluid is high. In order to pump such a job and ensure long term productivity from the fracture, understanding the behavior of the fracture fluid and proppant is critical. A series of laboratory experiments have been conducted to study conductivity and fracture width with high proppant loading, high temperature and high pressure. Proppant was manually placed in the fracture and fracture fluid was pumped through the pack. Conductivity was measured by pumping oil to simulate reservoir conditions. Proppant performance and fracture fluids, which carry the proppant into the fracture, and their subsequent clean-up during production, were studied. High strength proppant is ideal for deep fracture stimulations and in this study different proppant loadings at different stresses were tested to see the impact of crushing and fracture width reduction on fracture conductivity. The preliminary test results indicated that oil at reservoir conditions improves clean-up of fracture fluid left in the proppant pack compared with using water at ambient temperature. Increasing the proppant concentration in the fracture showed higher conductivity values in some cases even at high closure stress. The increase in effective closure stress with high temperature resulted in a significant loss in conductivity. Additionally, the fracture width decreased with time and increased effective closure stress. Tests were also run to study the effect of cyclic loading which is expected to further decrease conductivity.

Download or read book ADVANCED FRACTURING TECHNOLOGY FOR TIGHT GAS written by and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary objective of this research was to improve completion and fracturing practices in gas reservoirs in marginal plays in the continental United States. The Bossier Play in East Texas, a very active tight gas play, was chosen as the site to develop and test the new strategies for completion and fracturing. Figure 1 provides a general location map for the Dowdy Ranch Field, where the wells involved in this study are located. The Bossier and other tight gas formations in the continental Unites States are marginal plays in that they become uneconomical at gas prices below $2.00 MCF. It was, therefore, imperative that completion and fracturing practices be optimized so that these gas wells remain economically attractive. The economic viability of this play is strongly dependent on the cost and effectiveness of the hydraulic fracturing used in its well completions. Water-fracs consisting of proppant pumped with un-gelled fluid is the type of stimulation used in many low permeability reservoirs in East Texas and throughout the United States. The use of low viscosity Newtonian fluids allows the creation of long narrow fractures in the reservoir, without the excessive height growth that is often seen with cross-linked fluids. These low viscosity fluids have poor proppant transport properties. Pressure transient tests run on several wells that have been water-fractured indicate a long effective fracture length with very low fracture conductivity even when large amounts of proppant are placed in the formation. A modification to the water-frac stimulation design was needed to transport proppant farther out into the fracture. This requires suspending the proppant until the fracture closes without generating excessive fracture height. A review of fracture diagnostic data collected from various wells in different areas (for conventional gel and water-fracs) suggests that effective propped lengths for the fracture treatments are sometimes significantly shorter than those predicted by fracture models. There was no accepted optimal method for conducting hydraulic fracturing in the Bossier. Each operator used a different approach. Anadarko, the most active operator in the play, had tested at least four different kinds of fracture treatments. The ability to arrive at an optimal fracturing program was constrained by the lack of adequate fracture models to simulate the fracturing treatment, and an inability to completely understand the results obtained in previous fracturing programs. This research aimed at a combined theoretical, experimental and field-testing program to improve fracturing practices in the Bossier and other tight gas plays.

Download or read book Improvement of Hydraulic Fracture Conductivity Using Nanoparticles written by Reza Barati and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Hydraulic fracturing is a commonly used practice in the oil industry for well stimulation and production enhancement. With the general theme of the oil and gas industry moving toward systems with nano-sized pores, nanoparticles have gained a significant amount of attention especially in the field of hydraulic fracturing. Several groups have developed different nanoparticle systems that improve hydraulic fracture conductivity. This paper is a review of the highlighted work published in the area of application of nanoparticles to improve fracture conductivity. Nanotechnology can be used to improve the efficiency of hydraulic fracturing process. Four major production challenges faced by the oil and gas industry including incomplete filter cake cleanup, proppant pack damage, formation damage, and having micro-fractures that are not packed with proppants and will close under closure stress are introduced in this work. Solutions have also been reported using the advances in nanotechnology to address some of these challenges.

Download or read book Rock Fractures and Fluid Flow written by National Research Council and published by National Academies Press. This book was released on 1996-08-27 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt: Scientific understanding of fluid flow in rock fracturesâ€"a process underlying contemporary earth science problems from the search for petroleum to the controversy over nuclear waste storageâ€"has grown significantly in the past 20 years. This volume presents a comprehensive report on the state of the field, with an interdisciplinary viewpoint, case studies of fracture sites, illustrations, conclusions, and research recommendations. The book addresses these questions: How can fractures that are significant hydraulic conductors be identified, located, and characterized? How do flow and transport occur in fracture systems? How can changes in fracture systems be predicted and controlled? Among other topics, the committee provides a geomechanical understanding of fracture formation, reviews methods for detecting subsurface fractures, and looks at the use of hydraulic and tracer tests to investigate fluid flow. The volume examines the state of conceptual and mathematical modeling, and it provides a useful framework for understanding the complexity of fracture changes that occur during fluid pumping and other engineering practices. With a practical and multidisciplinary outlook, this volume will be welcomed by geologists, petroleum geologists, geoengineers, geophysicists, hydrologists, researchers, educators and students in these fields, and public officials involved in geological projects.

Download or read book Laboratory Study to Identify the Impact of Fracture Design Parameters Over the Final Fracture Conductivity Using the Dynamic Fracture Conductivity Test Procedure written by Andres Eduardo Pieve La Rosa and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This investigation carried out the analysis of fracture conductivity in a tight reservoir using laboratory experiments, by applying the procedure known as the dynamic fracture conductivity test. Considering the large number of experiments necessary to evaluate the effect of each parameter and the possible interaction of their combinations, the schedules of experiments were planned using a fractional factorial design. This design is used during the initial stage of studies to identify and discharge those factors that have little or no effect. Finally, the most important factors can then be studied in more detail during subsequent experiments. The objectives of this investigation were focused on identifying the effect of formation parameters such as closure stress, and temperature and fracture fluid parameters such as proppant loading over the final conductivity of a hydraulic fracture treatment. With the purpose of estimating the relation between fracture conductivity and the design parameters, two series of experiments were performed. The first set of experiments estimated the effects of the aliases parameters. The isolated effect of each independent parameter was obtained after the culmination of the second set of experiments. The preliminary test results indicated that the parameters with major negative effect over the final conductivity were closure stress and temperature. Some additional results show that proppant distribution had a considerable role over the final fracture conductivity when a low proppant concentration was used. Channels and void spaces in the proppant pack were detected on these cases improving the conductivity of the fracture, by creating paths of high permeability. It was observed that with experiments at temperatures around 250 degrees F, the unbroken gel dried up creating permeable scales that resulted in a significant loss in conductivity. The results of this investigation demonstrated that dynamic fracture conductivity test procedure is an excellent tool to more accurately represent the effects of design parameters over the fracture conductivity. These results are also the first step in the development of a statistical model that can be used to predict dynamic fracture conductivity.

Download or read book Hydraulic Fracturing Chemicals and Fluids Technology written by Johannes Fink and published by Gulf Professional Publishing. This book was released on 2013-08-14 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: When classifying fracturing fluids and their additives, it is important that production, operation, and completion engineers understand which chemical should be utilized in different well environments. A user's guide to the many chemicals and chemical additives used in hydraulic fracturing operations, Hydraulic Fracturing Chemicals and Fluids Technology provides an easy-to-use manual to create fluid formulations that will meet project-specific needs while protecting the environment and the life of the well. Fink creates a concise and comprehensive reference that enables the engineer to logically select and use the appropriate chemicals on any hydraulic fracturing job. The first book devoted entirely to hydraulic fracturing chemicals, Fink eliminates the guesswork so the engineer can select the best chemicals needed on the job while providing the best protection for the well, workers and environment. Pinpoints the specific compounds used in any given fracturing operation Provides a systematic approach to classifying fracturing fluid technology to meet specific project needs Eliminates guesswork with easy-to-understand language on selection and components of hydraulic fracturing chemicals Addresses environmental aspects of chemicals to safeguard employees and protect the environment

Download or read book Slickwater Proppant Transport in Complex Hydraulic Fracture Networks written by Msalli A. Alotaibi and published by . This book was released on 2015 with total page 201 pages. Available in PDF, EPUB and Kindle. Book excerpt: