Download or read book Improved Utilization of Lumber in Glued Laminated Beams written by Russell Charles Moody and published by . This book was released on 1977 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Efficient Utilization of Red Maple Lumber in Glued laminated Timber Beams written by John J. Janowiak and published by . This book was released on 1995 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Improved Performance of Southern Pine Structural Glued laminated Timber written by Roland Hernandez and published by . This book was released on 1992 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Improved Utilization of Small diameter Ponderosa Pine in Glued laminated Timber written by and published by . This book was released on 2005 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Strength and Stiffness of Reinforced Yellow poplar Glued laminated Beams written by and published by . This book was released on 1997 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: In bridge applications, it is often necessary to minimize the depth of the bridge structure to provide for the required hydraulic opening or reduce the volume of approach fill. For bridges that utilize structural glued-laminated (glulam) timber beams as stringers, reinforcement using thin strips of pultruded E-glass-fiber-reinforced plastic (GFRP) composites may permit reduced depth, because the reinforcement has the potential to increase stiffness and strength. This study is part of an overall effort aimed at evaluating the potential for commercial production of glulam-GFRP beams in current wood laminating plants and a wood adhesive compatible with existing equipment. Twelve Yellow-Poplar glulam GFRP beams were commercially manufactured, and their performance was evaluated. The GFRP panels were bonded to the wood with a resorcinol formaldehyde adhesive to provide the reinforcement. The simplicity of the process used to manufacture the test beams indicates that the commercial production of glulam-GFRP beams is feasible. Increases of 18 percent in stiffness and 26 percent in strength were achieved by adding 3 percent of GFRP by volume. The bending strength values of the beams predicted by the ASTM D3737 procedure correlate well with the experimental values. However, the observed delamination of the reinforcement indicates that improved bonding strength of wood--GFRP interfaces is needed. Results of this study will be useful to manufacturers interested in improving the performance of glulam timber beams.

Download or read book Effective thickness of paper written by Michael R. Rosenthal and published by . This book was released on 1977 with total page 564 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Design criteria for large structural glued laminated timber beams using mixed species of visually graded lumber written by Russell Charles Moody and published by . This book was released on 1974 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Improved Performance of Southern Pine Structural Glued laminated Timber written by Roland Hernandez and published by . This book was released on 1992 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Strength Validation and Fire Endurance of Glued laminated Timber Beams written by Erwin L. Schaffer and published by . This book was released on 1986 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: A previous paper presented a reliability-based model to predict the strength of glued-laminated timber beams at both room temperature and during fire exposure. This Monte Carlo simulation procedure generates strength and fire endurance (time-to-failure, TTF) data for glued-laminated beams that allow assessment of mean strength and TTF as well as their variability. This paper reports an effort to validate model predictive capability through an independently fabricated set of 21 glued-laminated beams. Based upon the available data for the model input parameters on lumber strength and stiffness, finger-joint strength, and length of laminating lumber between sequential finger joints, the model of beam strength appears acceptable and possibly slightly conservative. Refinements in the beam strength model allow its use for predicting fire endurance. In this case, the fire endurance is measured by the TTF and is defined as the time the beam will support its design load while subjected to fire. The residual strength of the beam is analytically calculated by removing the char layer, plus a finite thickness of weakened wood, from the beam cross section as fire exposure time increases. Employing the input parameters for values of finger-joint strength and lamination grades of Douglas-fir, the fire endurance TTF was analyzed for a 5.12- by 16.50-inch 11-lamination Douglas Fir-Larch beam (24F-V4) carrying full allowable uniform load (47.7 lb/in.). (Three-sided fire exposure was assumed; however, four-sided exposure can also be accommodated.) A simulated random fabrication and analysis of the TTF under fire exposure for 100 beams was performed. The mean TTF was estimated as 35.2 minutes with a coefficient of variation of 13.7 percent. Lateral torsional buckling was never the cause of failure in any of the simulations. The results compared well (within a 65 pct confidence band) with the observations and predictions for timber beams reported by sources in other countries. A simulation for a single glulam beam test in cooperation with the National Forest Products Association was also conducted which predicted the result exactly.

Download or read book Strength and Stiffness of Small Glued laminated Beams with Different Qualities of Tension Laminations written by Catherine M. Marx and published by . This book was released on 1981 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fiber Stress Values for Design of Glulam Timber Utility Structures written by Roland Hernandez and published by . This book was released on 1995 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Bending Strength of Water soaked Glued Laminated Beams written by Ronald W. Wolfe and published by . This book was released on 1978 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book PELPS III a Microcomputer Price Endogenous Linear Programming System for Economic Modeling written by Dali Zhang and published by . This book was released on 1993 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Research Paper FPL RP written by and published by . This book was released on 1986 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Utilization of Hardwoods Growing on Southern Pine Sites written by Peter Koch and published by . This book was released on 1985 with total page 3710 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermal Degradation of Fire retardant treated Plywood written by and published by . This book was released on 1991 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Long term Load Performance of Hardboard I beams written by J. Dobbin McNatt and published by . This book was released on 1983 with total page 688 pages. Available in PDF, EPUB and Kindle. Book excerpt: