Download or read book High Temperature Corrosion of Intermetallics written by Zhengwei Li and published by . This book was released on 2009 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intermetallic compounds can be simply defined as ordered alloy phases formed between two or more metallic elements. These materials have different crystal structures from those of the constituent metallic components and exhibit as long-range ordered superlattices. Their relatively low density, high melting point, high specific strength and due ductility make them the promising high temperature structural materials for aviation and aerospace applications. Among the big family of intermetallics, Fe-Al, Ni-Al and Ti-Al systems are attracting most of the attention. The objective of studies is to develop and utilize these intermetallic compounds as a type of important structural material whose overall properties is between nickel-based superalloys and advanced ceramics. However, a balance cannot always be achieved between mechanical and environmental properties. For example, iron aluminides have excellent resistance against oxidation and hot corrosion, however, their strength is relatively low. The higher specific strength and modulus than conventional Ni-based superalloys make Ti-Al intermetallic compounds of interest for aero-engine components, but the oxidation resistance of Ti-containing intermetallics is much lower than desirable; thus a key factor in increasing the maximum temperature in service is enhancing their oxidation and hot corrosion resistance while maintaining the excellent mechanical properties. This book is then intended to give an overview on the major efforts made over the last 20 years on high temperature oxidation and protection of intermetallic compounds including Fe-Al, Ni-Al and Ti-Al. In particular, the focus will be given to Ti-Al systems. After a general introduction on the structural and mechanical properties, the studies on the oxidation behaviours of these intermetallic compounds will be summarised based on the experimental observation reported in open literature. The emphasis will be put on the effects of alloying element, microstructure and coating/surface treatment. It should also be noted that only high temperature oxidation properties in air or oxygen are addressed; no discussion on hot corrosion, carburization, nitridation and sulfidation.
Download or read book Intermetallics Research Progress written by Yakov N. Berdovsky and published by Nova Publishers. This book was released on 2008 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intermetallics is concerned with all aspects of ordered chemical compounds between two or more metals and notably with their applications. This book covers new and important research on the crystal chemistry and bonding theory of intermetallics; determination and analysis of phase diagrams; the nature of superlattices, antiphase domains and order-disorder transitions; the geometry and dynamics of dislocations and related defects in intermetallics; theory and experiments relating to flow stress, work-hardening, fatigue and creep; response of deformed intermetallics to annealing; magnetic and electrical properties of intermetallics; structure and properties of grain and interphase boundaries; the effect of deviations from stoichiometry on physical and mechanical properties; crystallisation of intermetallics from the melt or amorphous precursors.
Download or read book Oxidation of High temperature Intermetallics written by Toni Grobstein and published by . This book was released on 1988 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oxidation of Intermetallics written by Hans Jürgen Grabke and published by John Wiley & Sons. This book was released on 2008-07-11 with total page 366 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the last ten years vast efforts were made in the research and development of intermetallic compounds to attain improved high temperature strength and low temperature ductility. These new structural materials are used in several high-temperature applications like engines and turbines. Oxidation and corrosion resistance are as important for the current applications of these materials as mechanical properties. This book gives a sound review of the present knowledge of the oxidation kinetics and mechanisms of intermetallics. Especially Ti-, Ni- and Fe-aluminides are treated in detail by experts from Europe, USA and Japan. The information provided will be of wealth for any engineer and scientist- materials scientist, physicist or chemist - involved in the development of new intermetallic materials and their applications.
Download or read book High Temperature Corrosion of FeAl Intermetallic Compounds written by Chunhua Xu and published by . This book was released on 1999 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oxidation and Corrosion of Intermetallic Alloys written by Gerhard Welsch and published by ASM International(OH). This book was released on 1996 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook provides researchers and development engineers with essential information on intermetallics for high temperature applications. The information will enable users to make choices by considering cost, properties, and performance for long-term use at elevated temperatures and in other adverse environmental conditions. It provides an overview of processing, structural and mechanical properties, applications, behavior and endurance at high temperature and in oxidizing conditions. It also focuses on 'pesting' disintegration, corrosion and oxidation phenomena at intermediate temperatures, corrosion embrittlement at ambient temperatures, aqueous corrosion and corrosion sensitive embrittlement properties.
Download or read book Developments in High Temperature Corrosion and Protection of Materials written by W Gao and published by Elsevier. This book was released on 2008-04-09 with total page 677 pages. Available in PDF, EPUB and Kindle. Book excerpt: High temperature corrosion is a phenomenon that occurs in components that operate at very high temperatures, such as gas turbines, jet engines and industrial plants. Engineers are constantly striving to understand and prevent this type of corrosion. This book examines the latest developments in the understanding of high temperature corrosion processes and protective oxide scales and coatings. Part one looks at high temperature corrosion. Chapters cover diffusion and solid state reactions, external and internal oxidation of alloys, metal dusting corrosion, tribological degradation, hot corrosion, and oxide scales on hot-rolled steel strips. Modern techniques for analysing high temperature oxidation and corrosion are also discussed. Part two discusses methods of protection using ceramics, composites, protective oxide scales and coatings. Chapters focus on layered ternary ceramics, alumina scales, Ti-Al intermetallic compounds, metal matrix composites, chemical vapour deposited silicon carbide, nanocrystalline coatings and thermal barrier coatings. Part three provides case studies illustrating some of the challenges of high temperature corrosion to industry and how they can be overcome. Case studies include the petrochemical industry, modern incinerators and oxidation processing of electronic materials. This book is a valuable reference tool for engineers who develop heat resistant materials, mechanical engineers who design and maintain high temperature equipment and plant, and research scientists and students who study high temperature corrosion and protection of materials. Describes the latest developments in understanding high temperature corrosion Presents the latest research by the leading innovators from around the globe Case studies are provided to illustrate key points
Download or read book High Temperature Corrosion and Materials Applications written by George Y. Lai and published by ASM International. This book was released on 2007-01-01 with total page 469 pages. Available in PDF, EPUB and Kindle. Book excerpt: George Lai's 1990 book, High-Temperature Corrosion of Engineering Alloys, is recognized as authoritative and is frequently consulted and often cited by those in the industry. His new book, almost double in size with seven more chapters, addresses the new concerns, new technologies, and new materials available for those engaged in high-temperature applications. As we strive for energy efficiency, the realm of high-temperature environments is expanding and the need for information on high temperature materials applications was never greater. In addition to extensive expansion on most of the content of the original book, new topics include erosion and erosion-corrosion, low NOx combustion in coal-fired boilers, fluidized bed combustion, and the special demands of waste-to-energy boilers, waste incinerators, and black liquor recovery boilers in the pulp and paper industry. The corrosion induced by liquid metals is discussed and protection options are presented.
Download or read book High Temperature Corrosion and Materials Chemistry written by Michael McNallan and published by The Electrochemical Society. This book was released on 2000 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Intermetallic Compounds written by Mahmood Aliofkhazraei and published by BoD – Books on Demand. This book was released on 2018-05-30 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intermetallic compounds are usually brittle with high melting points. Their properties are often found among ceramic and metallic materials. In most cases, their hot corrosion resistance and simultaneously hardness are important. One of the main applications of intermetallic compounds is for superalloy turbine blades in which they show appropriate high-temperature-related properties. This book collects new developments about intermetallic compounds and their recent usages.
Download or read book High Temperature Corrosion and Materials Chemistry IV written by Elizabeth J. Opila and published by The Electrochemical Society. This book was released on 2003 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: " ... papers presented at the Fourth International Symposium on High Temperature Corrosion and Materials Chemistry, held at the 203rd meeting of the Electrochemical Society, Inc., in Paris, France, April 30- May 2, 2003"--Preface.
Download or read book High Temperature Corrosion and Materials Chemistry III written by Electrochemical Society. High Temperature Materials Division and published by The Electrochemical Society. This book was released on 2001 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanisms of High Temperature Corrosion written by Pierre Sarrazin and published by Trans Tech Publications Ltd. This book was released on 2008-02-01 with total page 335 pages. Available in PDF, EPUB and Kindle. Book excerpt: The oxidation of metals is, by definition, a reaction between a gas and a solid which usually produces a solid reaction product. At first glance, this would therefore seem to be a very simple process but, in fact, it is considerably more complex. One would like to think that the reaction product, i.e., the scale that forms on the metal, acts as a physical barrier between the reactants, and that the reaction should thus cease once the barrier is established. We know that this is unfortunately not the case, because transport of matter through the scale allows the reaction to continue. We also know that, because of density-differences between the metal and its oxide, the scale may not be sufficiently complete in coverage or may not adhere to the substrate because of cracking, spalling and detachment (wrinkling). In some extreme cases, the scale may even be a liquid which simply drips from the surface, or it may volatilize at operational temperatures. The reaction between a gas and a metal is truly very complicated.
Download or read book High Temperature Aluminides and Intermetallics written by S.H. Whang and published by Elsevier. This book was released on 2013-10-22 with total page 759 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume of proceedings is concerned with an increasingly important area, that of intermetallics and high temperature aluminides, which has recently been attracting a great deal of attention. Nearly 150 papers presented at the meeting held in San Diego in September 1991 are reproduced here. They cover a wide range of related topics such as the bonding characteristic and alloying behaviour of TiA1 intermetallic compounds and the cleavage fracture of ordered intermetallic alloys. All the papers have been reviewed according to the standards set by Materials Science and Engineering. This book will be of interest to metallurgists and materials scientists working with composites who are interested in the latest developments in this fast–moving field.
Download or read book Introduction to High Temperature Oxidation and Corrosion written by A. S. Khanna and published by ASM International. This book was released on 2002-01-01 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text for graduate and post graduate students covers fundamentals of high temperature corrosion and related topics. Early chapters cover the thermodynamics and kinetics of oxidation and defect structure of oxides and diffusion in oxides, and later chapters cover thin and thick layer oxidation, o
Download or read book Introduction to the High Temperature Oxidation of Metals written by Neil Birks and published by Cambridge University Press. This book was released on 2006-03-30 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: A straightforward treatment describing the oxidation processes of metals and alloys at elevated temperatures. This 2006 second edition retains the fundamental theory but incorporates advances made in understanding degradation phenomena. The first half provides an authoritative introduction to the basic principles, covering thermodynamics and mechanisms of high temperature corrosion of metals and alloys. The latter half extends the discussion to oxidation processes in complex systems, from reactions in mixed environments to protective techniques, including coatings and atmosphere control. The authors provide a logical and expert treatment of the subject, producing a revised edition that will be a comprehensive guide to material scientists and engineers requiring an understanding of this elementary process.
Download or read book Materials Under Extreme Conditions written by A. K. Tyagi and published by Elsevier. This book was released on 2017-01-13 with total page 872 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials Under Extreme Conditions: Recent Trends and Future Prospects analyzes the chemical transformation and decomposition of materials exposed to extreme conditions, such as high temperature, high pressure, hostile chemical environments, high radiation fields, high vacuum, high magnetic and electric fields, wear and abrasion related to chemical bonding, special crystallographic features, and microstructures. The materials covered in this work encompass oxides, non-oxides, alloys and intermetallics, glasses, and carbon-based materials. The book is written for researchers in academia and industry, and technologists in chemical engineering, materials chemistry, chemistry, and condensed matter physics. Describes and analyzes the chemical transformation and decomposition of a wide range of materials exposed to extreme conditions Brings together information currently scattered across the Internet or incoherently dispersed amongst journals and proceedings Presents chapters on phenomena, materials synthesis, and processing, characterization and properties, and applications Written by established researchers in the field
