Download or read book Maraging Steels written by W Sha and published by Elsevier. This book was released on 2009-10-26 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt: Maraging steels are high-strength steels combined with good toughness. They are used particularly in aerospace and tooling applications. Maraging refers to the ageing of martensite, a hard microstructure commonly found in steels.Maraging steels: modelling of microstructure, properties and applications covers the following topics: Introduction to maraging steels; Microstructure of maraging steels; Mechanical properties of maraging steels; Thermodynamic calculations for quantifying the phase fraction and element partition in maraging systems and precipitation hardening steels; Quantification of phase transformation kinetics in maraging steels; Quantification of age hardening in maraging steels; Maraging steels and overageing; Precipitation hardening stainless steel; Applications of artificial neural network on modelling maraging steel properties.With its distinguished authors, Maraging steels: modelling of microstructure, properties and applications is a standard reference for industry and researchers concerned with maraging steels and modelling as well as users of maraging steels in the aerospace and tooling sectors. The book includes both conventional maraging steels and precipitation hardened (PH) stainless steels. Provides an overview of maraging steels including microstructure and mechanical properties Reviews thermodynamic calculations for quantifying the phase fraction and element partition in maraging steels Includes chapters on the quantification of phase transformation kinetics and age hardening in maraging steels

Download or read book The Mechanical Properties of the 18 Per Cent Nickel Maraging Steels written by J. E. Campbell and published by . This book was released on 1964 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the combination of tensile properties and toughness that can be obtained with the maraging steels is higher than can be achieved with other steels by simple heat treatments, there is considerable interest in using the maraging steels for critical components such as rocket motor cases, pressure vessels, and aircraft forgings. This report includes information on the tensile, compressive, shear, bearing, dynamic modulus, impact, bend, fatigue, creep, and rupture properties of the 18 per cent nickel maraging steels and on the effect of temperature on these properties. Data for the properties of sheet, bar, and forgings, as well as data illustrating the effect of cold rolling, variation in the heat treatment, and elevated-temperature exposure also are presented. Data on the effect of specimen orientation, which are also included, indicate that the ductility and toughness of specimens designed to evaluate the properties in the short transverse direction are somewhat lower than in the other directions. The high strength and toughness that can be obtained in the 18 per cent nickel maraging steels make them attractive for certain critical applications that require these properties. The fabrication characteristics, weldability, and simple heat treatment are other advantages of these steels. (Author).

Download or read book High Strength Maraging Steels written by M. D. Perkas and published by . This book was released on 1974 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reviews fracture, mechanical properties, stress corrosion and composition relations for maraging steel.

Download or read book Introduction to Aerospace Materials written by Adrian P Mouritz and published by Elsevier. This book was released on 2012-05-23 with total page 640 pages. Available in PDF, EPUB and Kindle. Book excerpt: The structural materials used in airframe and propulsion systems influence the cost, performance and safety of aircraft, and an understanding of the wide range of materials used and the issues surrounding them is essential for the student of aerospace engineering.Introduction to aerospace materials reviews the main structural and engine materials used in aircraft, helicopters and spacecraft in terms of their production, properties, performance and applications. The first three chapters of the book introduce the reader to the range of aerospace materials, focusing on recent developments and requirements. Following these introductory chapters, the book moves on to discuss the properties and production of metals for aerospace structures, including chapters covering strengthening of metal alloys, mechanical testing, and casting, processing and machining of aerospace metals. The next ten chapters look in depth at individual metals including aluminium, titanium, magnesium, steel and superalloys, as well as the properties and processing of polymers, composites and wood. Chapters on performance issues such as fracture, fatigue and corrosion precede a chapter focusing on inspection and structural health monitoring of aerospace materials. Disposal/recycling and materials selection are covered in the final two chapters. With its comprehensive coverage of the main issues surrounding structural aerospace materials,Introduction to aerospace materials is essential reading for undergraduate students studying aerospace and aeronautical engineering. It will also be a valuable resource for postgraduate students and practising aerospace engineers. Reviews the main structural and engine materials used in aircraft, helicopters and space craft in terms of their properties, performance and applications Introduces the reader to the range of aerospace materials, focusing on recent developments and requirements, and discusses the properties and production of metals for aerospace structures Chapters look in depth at individual metals including aluminium, titanium, magnesium, steel and superalloys

Download or read book Source Book on Maraging Steels written by Raymond Frank Decker and published by ASM International(OH). This book was released on 1979 with total page 408 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Report on Meeting to Review Maraging Steel Projects written by Albert M. Hall and published by . This book was released on 1962 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Metallurgy Behavior and Application of the 18 percent Nickel Maraging Steels written by Albert M. Hall and published by . This book was released on 1968 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Steels written by Wei Sha and published by Springer Science & Business Media. This book was released on 2013-01-11 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steels and computer-based modelling are fast growing fields in materials science as well as structural engineering, demonstrated by the large amount of recent literature. Steels: From Materials Science to Structural Engineering combines steels research and model development, including the application of modelling techniques in steels. The latest research includes structural engineering modelling, and novel, prototype alloy steels such as heat-resistant steel, nitride-strengthened ferritic/martensitic steel and low nickel maraging steel. Researchers studying steels will find the topics vital to their work. Materials experts will be able to learn about steels used in structural engineering as well as modelling and apply this increasingly important technique in their steel materials research and development.

Download or read book Welding High strength Steels written by P. A. Kammer and published by . This book was released on 1966 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent studies of the developments in welding steels with yield strengths greater than 150 ksi have included low-alloy martensitic steels, medium-alloy martensitic steels, nickel maraging steels, and bainitic steels. Only weldments from medium-alloy martensitic steels and nickel maraging steels have mechanical properties approaching those of the base plate without a complete postweld heat treatment. The most serious problem with the other steel is low toughness in the weld fusion zone. Adequate weld metal toughness under conditions of elastic strain can be obtarined over the entire 150 to 225 ksi yield-strength range only if the tungsten-arc welding process is used. Processes with higher deposition rates can produce comparable weld deposits only in the lower portion of the range. Above a yield strength of 200 ksi, 18Ni maraging steel weldments have the best combination of strength and toughness. Below 200 ksi, the HP 9-4-25 medium-alloy martensitic steel and 12Ni maraging steel weldments have nearly equal properties.

Download or read book Report on the Fourth Maraging steel Project Review written by Albert M. Hall and published by . This book was released on 1964 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Report on the Third Maraging Steel Project Review written by Albert M. Hall and published by . This book was released on 1963 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Split Hopkinson Kolsky Bar written by Weinong W. Chen and published by Springer Science & Business Media. This book was released on 2010-11-11 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt: The authors systematically describe the general principles of Kolsky bars, or split Hopkinson bars, which are widely used for obtaining dynamic material properties. Modifications are introduced for obtaining reliable data. Specific experiment design guidelines are provided to subject the specimen to desired testing conditions. Detailed Kolsky-bar examples are given for different classes of materials (brittle, ductile, soft, etc) and for different loading conditions (tension, torsion, triaxial, high/low temperatures, intermediate strain rate, etc). The Kolsky bars used for dynamic structural characterization are briefly introduced. A collection of dynamic properties of various materials under various testing conditions is included which may serve as a reference database. This book assists both beginners and experienced professionals in characterizing high-rate material response with high quality and consistency. Readers who may benefit from this work include university students, instructors, R & D professionals, and scholars/engineers in solid mechanics, aerospace, civil and mechanical engineering, as well as materials science and engineering.

Download or read book Basics of Cutting and Abrasive Processes written by Hans Kurt Toenshoff and published by Springer Science & Business Media. This book was released on 2013-06-12 with total page 405 pages. Available in PDF, EPUB and Kindle. Book excerpt: Manufacturing is the basic industrial activity generating real value. Cutting and abrasive technologies are the backbone of precision production in machine, automotive and aircraft building as well as of production of consumer goods. We present the knowledge of modern manufacturing in these technologies on the basis of scientific research. The theory of cutting and abrasive processes and the knowledge about their application in industrial practice are a prerequisite for the studies of manufacturing science and an important part of the curriculum of the master study in German mechanical engineering. The basis of this book is our lecture “Basics of cutting and abrasive processes” (4 semester hours/3 credit hours) at the Leibniz University Hannover, which we offer to the diploma and master students specializing in manufacturing science.

Download or read book Welding of Maraging Steels written by F. H. Lang and published by . This book was released on 1971 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Multiaxial Fatigue written by Darrell Socie and published by SAE International. This book was released on 1999-12-15 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides practicing engineers, researchers, and students with a working knowledge of the fatigue design process and models under multiaxial states of stress and strain. Readers are introduced to the important considerations of multiaxial fatigue that differentiate it from uniaxial fatigue.

Download or read book Maraging Steels for Ultra high Strength Applications written by International Nickel Co and published by . This book was released on 1962 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Phase Transformations in Steels written by Elena Pereloma and published by Elsevier. This book was released on 2012-05-11 with total page 673 pages. Available in PDF, EPUB and Kindle. Book excerpt: The processing-microstructure-property relationships in steels continue to present challenges to researchers because of the complexity of phase transformation reactions and the wide spectrum of microstructures and properties achievable. This major two-volume work summarises the current state of research on phase transformations in steels and its implications for the emergence of new steels with enhanced engineering properties.Volume 2 reviews current research on diffusionless transformations and phase transformations in high strength steels, as well as advances in modelling and analytical techniques which underpin this research. Chapters in part one discuss the crystallography and kinetics of martensite transformations, the morphology, substructure and tempering of martensite as well as shape memory in ferrous alloys. Part two summarises research on phase transformations in high strength low alloy (HSLA) steels, transformation induced plasticity (TRIP)-assisted multiphase steels, quenched and partitioned steels, advanced nanostructured bainitic steels, high manganese twinning induced plasticity (TWIP) and maraging steels. The final two parts of the book review advances in modelling and the use of advanced analytical techniques to improve our understanding of phase transformations in steels.With its distinguished editors and distinguished international team of contributors, the two volumes of Phase transformations in steels is a standard reference for all those researching the properties of steel and developing new steels in such areas as automotive engineering, oil and gas and energy production. Alongside its companion volume, this major two-volume work summarises the current state of research on phase transformations in steels Reviews research on diffusionless transformations and phase transformations in high strength steels Examines advances in modelling and the use of advanced analytical techniques to improve understanding of phase transformations in steels