Download or read book High Frequency Continuous Time Filters in Digital CMOS Processes written by Shanthi Pavan and published by Springer Science & Business Media. This book was released on 2007-05-08 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: There is an ever increasing trend towards putting entire systems on a single chip. This means that analog circuits will have to coexist on the same substrate along with massive digital systems. Since technologies are optimized with these digital systems in mind, designers will have to make do with standard CMOS processes in the years to come. We address analog filter design from this perspective. Filters form important blocks in applications ranging from computer disc-drive chips to radio transceivers. In this book, we develop the theory and techniques necessary for the implementation of high frequency (hundreds of megahertz) programmable continuous time filters in standard CMOS processes. Since high density poly-poly capacitors are not available in these technologies, alternative capacitor structures have to be found. Met- metal capacitors have low specific capacitance. An alternative is to use the (inherently nonlinear) capacitance formed by MOSFET gates. In Chapter 2, we focus on the use of MOS capacitors as integrating elements. A physics-based model which predicts distortion accurately is presented for a two-terminal MOS structure in accumulation. Distortion in these capacitors as a function of signal swing and bias voltage is computed. Chapter 3 reviews continuous-time filter architectures in the light of bias-dependent integrating capacitors. We also discuss the merits and demerits of various CMOS transconductance elements. The problems encountered in designing high frequency programmable filters are discussed in detail.
Download or read book High Frequency Continuous Time Filters in Digital CMOS Processes written by Shanthi Pavan and published by . This book was released on 2014-01-15 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Frequency Continous Time Filters in Digital CMOS Processes written by Shanthi Pavan Y and published by . This book was released on 1999 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Performance CMOS Continuous Time Filters written by José Silva-Martínez and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-Performance CMOS Continuous-Time Filters is devoted to the design of CMOS continuous-time filters. CMOS is employed because the most complex integrated circuits have been realized with this technology for two decades. The most important advantages and drawbacks of continuous-time filters are clearly shown. The transfer function is one of the most important filter parameters but several others (like intermodulation distortion, power-supply rejection ratio, noise level and dynamic range) are fundamental in the design of high-performance systems. Special attention is paid to the practical aspects of the design, which shows the difference between an academic design and an industrial design. A clear understanding of the behavior of the circuits and techniques is preferred over complex equations or interpretation of simulated results. Step-by-step design procedures are very often used to clarify the use of the techniques and topologies. The organization of this text is hierarchical, starting with the design consideration of the basic building blocks and ending with the design of several high-performance continuous-time filters. Most of the circuits have been fabricated, theoretically analyzed and simulated, and silicon measurement results are compared with each other. High-Performance CMOS Continuous-Time Filters can be used as a text book for senior or graduate courses on this topic and can also be useful for industrial engineers as a reference book.
Download or read book Continuous Time Low Pass Filters for Integrated Wideband Radio Receivers written by Ville Saari and published by Springer Science & Business Media. This book was released on 2012-03-15 with total page 207 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a new filter design approach and concentrates on the circuit techniques that can be utilized when designing continuous-time low-pass filters in modern ultra-deep-submicron CMOS technologies for integrated wideband radio receivers. Coverage includes system-level issues related to the design and implementation of a complete single-chip radio receiver and related to the design and implementation of a filter circuit as a part of a complete single-chip radio receiver. Presents a new filter design approach, emphasizing low-voltage circuit solutions that can be implemented in modern, ultra-deep-submicron CMOS technologies;Includes filter circuit implementations designed as a part of a single-chip radio receiver in modern 1.2V 0.13um and 65nm CMOS;Describes design and implementation of a continuous-time low-pass filter for a multicarrier WCDMA base-station;Emphasizes system-level considerations throughout.
Download or read book Analog CMOS Filters for Very High Frequencies written by Bram Nauta and published by Springer Science & Business Media. This book was released on 1992-09-30 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrated circuit technology is widely used for the full integration of electronic systems. In general, these systems are realized using digital techniques implemented in CMOS technology. The low power dissipation, high packing density, high noise immunity, ease of design and the relative ease of scaling are the driving forces of CMOS technology for digital applications. Parts of these systems cannot be implemented in the digital domain and will remain analog. In order to achieve complete system integration these analog functions are preferably integrated in the same CMOS technology. An important class of analog circuits that need to be integrated in CMOS are analog filters. This book deals with very high frequency (VHF) filters, which are filters with cut-off frequencies ranging from the low megahertz range to several hundreds of megahertz. Until recently the maximal cut-off frequencies of CMOS filters were limited to the low megahertz range. By applying the techniques presented in this book the limit could be pushed into the true VHF domain, and integrated VHF filters become feasible. Application of these VHF filters can be found in the field of communication, instrumentation and control systems. For example, pre and post filtering for high-speed AD and DA converters, signal reconstruction, signal decoding, etc. The general design philosophy used in this book is to allow only the absolute minimum of signal carrying nodes throughout the whole filter. This strategy starts at the filter synthesis level and is extended to the level of electronic circuitry. The result is a filter realization in which all capacitators (including parasitics) have a desired function. The advantage of this technique is that high frequency parasitic effects (parasitic poles/zeros) are minimally present. The book is a reference for engineers in research or development, and is suitable for use as a text for advanced courses on the subject. >
Download or read book Advances in Solid State Circuit Technologies written by Paul Chu and published by BoD – Books on Demand. This book was released on 2010-04-01 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields.
Download or read book Low Power High Resolution Analog to Digital Converters written by Amir Zjajo and published by Springer Science & Business Media. This book was released on 2010-10-29 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: With the fast advancement of CMOS fabrication technology, more and more signal-processing functions are implemented in the digital domain for a lower cost, lower power consumption, higher yield, and higher re-configurability. This has recently generated a great demand for low-power, low-voltage A/D converters that can be realized in a mainstream deep-submicron CMOS technology. However, the discrepancies between lithography wavelengths and circuit feature sizes are increasing. Lower power supply voltages significantly reduce noise margins and increase variations in process, device and design parameters. Consequently, it is steadily more difficult to control the fabrication process precisely enough to maintain uniformity. The inherent randomness of materials used in fabrication at nanoscopic scales means that performance will be increasingly variable, not only from die-to-die but also within each individual die. Parametric variability will be compounded by degradation in nanoscale integrated circuits resulting in instability of parameters over time, eventually leading to the development of faults. Process variation cannot be solved by improving manufacturing tolerances; variability must be reduced by new device technology or managed by design in order for scaling to continue. Similarly, within-die performance variation also imposes new challenges for test methods. In an attempt to address these issues, Low-Power High-Resolution Analog-to-Digital Converters specifically focus on: i) improving the power efficiency for the high-speed, and low spurious spectral A/D conversion performance by exploring the potential of low-voltage analog design and calibration techniques, respectively, and ii) development of circuit techniques and algorithms to enhance testing and debugging potential to detect errors dynamically, to isolate and confine faults, and to recover errors continuously. The feasibility of the described methods has been verified by measurements from the silicon prototypes fabricated in standard 180nm, 90nm and 65nm CMOS technology.
Download or read book CMOS Analog Design Using All Region MOSFET Modeling written by Márcio Cherem Schneider and published by Cambridge University Press. This book was released on 2010-01-28 with total page 505 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covering the essentials of analog circuit design, this book takes a unique design approach based on a MOSFET model valid for all operating regions, rather than the standard square-law model. Opening chapters focus on device modeling, integrated circuit technology, and layout, whilst later chapters go on to cover noise and mismatch, and analysis and design of the basic building blocks of analog circuits, such as current mirrors, voltage references, voltage amplifiers, and operational amplifiers. An introduction to continuous-time filters is also provided, as are the basic principles of sampled-data circuits, especially switched-capacitor circuits. The final chapter then reviews MOSFET models and describes techniques to extract design parameters. With numerous design examples and exercises also included, this is ideal for students taking analog CMOS design courses and also for circuit designers who need to shorten the design cycle.
Download or read book High Frequency Continuous time Filters in CMOS Technology written by Scott T. Dupuie and published by . This book was released on 1991 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 1V CMOS Gm C Filters written by Tien-Yu Lo and published by Springer Science & Business Media. This book was released on 2009-04-21 with total page 169 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1V CMOS Gm-C Filters: Design and Applications discusses the design aspects of transconductor and Gm-C filter circuits, with a special focus on 1V circuit implementations. The emphasis is on high linearity voltage-to-current blocks for wireless and wireline applications, and the designs cover up to very high speed specifications. 1V CMOS Gm-C Filters: Design and Applications provides a clear introduction of low voltage architectures and yields insight into the influence of circuit non-idealities. The fully CMOS implementation could be useful for wireless and wireline applications. The basic design concepts can be easily constructed through the illustration of this book. This book can be provided for engineers and researchers who are interested in the transconductor and Gm-C filter. It is also a good reference for the course related to analog integrated circuit design.
Download or read book Analog Filters using MATLAB written by Lars Wanhammar and published by Springer Science & Business Media. This book was released on 2009-06-02 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook provides a complete introduction to analog filters for senior undergraduate and graduate students. Coverage includes the synthesis of analog filters and many other filter types including passive filters and filters with distributed elements.
Download or read book Cognitive Radio Receiver Front Ends written by Bodhisatwa Sadhu and published by Springer Science & Business Media. This book was released on 2013-10-11 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the architecture and circuit design for cognitive radio receiver front-ends. The authors first provide a holistic explanation of RF circuits for cognitive radio systems. This is followed by an in-depth exploration of existing techniques that can be utilized by circuit designers. Coverage also includes novel circuit techniques and architectures that can be invaluable for designers for cognitive radio systems.
Download or read book Analog CMOS Filters for Very High Frequencies written by Bram Nauta and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrated circuit technology is widely used for the full integration of electronic systems. In general, these systems are realized using digital techniques implemented in CMOS technology. The low power dissipation, high packing density, high noise immunity, ease of design and the relative ease of scaling are the driving forces of CMOS technology for digital applications. Parts of these systems cannot be implemented in the digital domain and will remain analog. In order to achieve complete system integration these analog functions are preferably integrated in the same CMOS technology. An important class of analog circuits that need to be integrated in CMOS are analog filters. This book deals with very high frequency (VHF) filters, which are filters with cut-off frequencies ranging from the low megahertz range to several hundreds of megahertz. Until recently the maximal cut-off frequencies of CMOS filters were limited to the low megahertz range. By applying the techniques presented in this book the limit could be pushed into the true VHF domain, and integrated VHF filters become feasible. Application of these VHF filters can be found in the field of communication, instrumentation and control systems. For example, pre and post filtering for high-speed AD and DA converters, signal reconstruction, signal decoding, etc. The general design philosophy used in this book is to allow only the absolute minimum of signal carrying nodes throughout the whole filter. This strategy starts at the filter synthesis level and is extended to the level of electronic circuitry. The result is a filter realization in which all capacitators (including parasitics) have a desired function. The advantage of this technique is that high frequency parasitic effects (parasitic poles/zeros) are minimally present. The book is a reference for engineers in research or development, and is suitable for use as a text for advanced courses on the subject. >
Download or read book Integrated Video Frequency Continuous Time Filters written by Scott D. Willingham and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in the state of the art mean the signal processing ICs of ever-increasing complexity are being introduced. While the typical portion of a large IC devoted to analog circuits has diminished, the performance of those surviving analog signal processing circuits remains vital and their design challenging. Moreover, the emerging high-definition TV technology has created a new area for IC development, one with formidable signal processing requirements. The antialiasing filters needed for one proposed HDTV decoder motivated the research documented in this book. Sharply selective filters place tight constraints on the permitted excess phase shifts of their constituent circuits. Combined with stringent requirements for low distortion at video frequencies, these constraints challenge the IC filter designer. Integrated Video-Frequency Continuous-Time Filters: High-Performance Realizations in BiCMOS deals with what is arguably the mainstay of analog signal processing circuits. Prominent applications in computer disk-drive read channels, video receivers, rf circuits, and antialiasing and reconstruction in data converters testifies to their importance. Moreover, they are excellent benchmarks for more general analog signal processors. Bipolar and MOSFET transistors, freely combined at the lowest circuit levels, provide the designer with an opportunity to develop potent variations on the standard idioms. The book considers the general principles of BiCMOS circuit design, through to a demanding design problem. This case-study approach allows a concrete discussion of the justification for and practical trade-offs of each design decision. Audience: A reference work for experienced IC designers and a text for advanced IC design students.
Download or read book CMOS Telecom Data Converters written by Angel Rodríguez-Vázquez and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: CMOS Telecom Data Converters compiles the latest achievements regarding the design of high-speed and high-resolution data converters in deep submicron CMOS technologies. The four types of analog-to-digital converter architectures commonly found in this arena are covered, namely sigma-delta, pipeline, folding/interpolating and flash. For all these types, latest achievements regarding the solution of critical architectural and circuital issues are presented, and illustrated through IC prototypes with measured state-of-the-art performances. Some of these prototypes are conceived to be employed at the chipset of newest generation wireline modems (ADSL and ADSL+). Others are intended for wireless transceivers. Besides analog-to-digital converters, the book also covers other functions needed for communication systems, such as digital-to-analog converters, analog filters, programmable gain amplifiers, digital filters, and line drivers.
Download or read book DCIS2002 written by Salvador Bracho del Pino and published by Ed. Universidad de Cantabria. This book was released on 2002 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: Este libro contiene las presentaciones de la XVII Conferencia de Diseño de Circuitos y Sistemas Integrados celebrado en el Palacio de la Magdalena, Santander, en noviembre de 2002. Esta Conferencia ha alcanzado un alto nivel de calidad, como consecuencia de su tradición y madurez, que lo convierte en uno de los acontecimientos más importantes para los circuitos de microelectrónica y la comunidad de diseño de sistemas en el sur de Europa. Desde su origen tiene una gran contribución de Universidades españolas, aunque hoy los autores participan desde catorce países
