Download or read book Helium Generation Rates in Isotopically Tailored Fe Cr Ni Alloys Irradiated in FFTF written by and published by . This book was released on 1991 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: Three Fe-Cr-Ni alloys have been doped with 0.4% 59Ni for side-by-side irradiations of doped and undoped materials in order to determine the effects of fusion-relevant levels of helium production on microstructural development and mechanical properties. The alloys were irradiated in three successive cycles of the Materials Open Test Assembly (MOTA) located in the Fast Flux Test Facility (FFTF). Following irradiation, helium levels were measured by isotope dilution mass spectrometry. The highest level of helium achieved in doped alloys was 172 appm at 9.1 dpa for a helium(appm)-to-dpa ratio of 18.9. The overall pattern of predicted helium generation rates in doped and undoped alloys is in good agreement with the helium measurements.
Download or read book Isotopic Tailoring with 59Ni to Study Helium Generation Rates and Their Effect on Tensile Properties of Neutron Irradiated Fe Cr Ni Alloys written by FA. Garner and published by . This book was released on 1994 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile testing on three model Fe-Cr-Ni alloys removed from four discharges of the 59Ni isotopic doping experiment in FFTF-MOTA indicates that helium/dpa ratios typical of fusion reactors do not produce changes in the yield strength or elongation that are significantly different from those at much lower helium generation rates. It also appears that tensile properties approach a saturation level that is dependent only on the final irradiation temperature, but not prior temperature history or thermomechanical starting condition. The saturation in mechanical properties reflects a similar saturation in microstructure that is independent of starting condition.
Download or read book Influence of Helium Generation Rate and Temperature History on Mechanical Properties of Model Fe Cr Ni Alloys Irradiated in FFTF at Relatively Low Displacement Rates written by and published by . This book was released on 1993 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: In agreement with earlier studies conducted at higher displacement rates, evolution of mechanical properties of model Fe-Cr-Ni alloys irradiated at lower displacement rates in the 59Ni isotopic doping experiment does not appear to be strongly affected by large differences in helium generation rate. This insensitivity to helium/dpa ratio is exhibited during both isothermal and non-isothermal irradiation. The overall behavior of the model alloys used in this study is dominated by the tendency to converge to a saturation strength level that is independent of thermomechanical starting state and helium/dpa ratio, but which is dependent on irradiation temperature and alloy composition.
Download or read book Isotopic Tailoring with 59Ni to Study the Effect of Helium on Microstructural Evolution and Mechanical Properties of Neutron irradiated Fe Cr Ni Alloys written by and published by . This book was released on 1992 with total page 29 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile testing on three model Fe-Cr-Ni alloys removed from four discharges of the 59Ni isotopic doping experiment in FFTF-MOTA indicates that helium/dpa ratios typical of fusion reactors do not produce changes in the yield strength or elongation that are significantly different from those at much lower helium generation rates. It also appears that tensile properties approach a saturation level that is dependent only on the final irradiation temperature, but not prior temperature history or thermomechanical starting condition. The saturation in mechanical properties reflects a similar saturation in microstructure that is independent of starting condition. The successful conduct of an isotopic doping experiment was found to require post-irradiation measurement of the helium levels in order to compensate for uncertainties in the cross sections for burn-out and burn-in of 59Ni and for uncertainties in neutron flux and spectra in the vicinity of the edge of the core.
Download or read book Isotopic Tailoring with Sup 59 Ni to Study the Effect of Helium on Microstructural Evolution and Mechanical Properties of Neutron irradiated Fe Cr Ni Alloys written by and published by . This book was released on 1992 with total page 29 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile testing on three model Fe-Cr-Ni alloys removed from four discharges of the 59Ni isotopic doping experiment in FFTF-MOTA indicates that helium/dpa ratios typical of fusion reactors do not produce changes in the yield strength or elongation that are significantly different from those at much lower helium generation rates. It also appears that tensile properties approach a saturation level that is dependent only on the final irradiation temperature, but not prior temperature history or thermomechanical starting condition. The saturation in mechanical properties reflects a similar saturation in microstructure that is independent of starting condition. The successful conduct of an isotopic doping experiment was found to require post-irradiation measurement of the helium levels in order to compensate for uncertainties in the cross sections for burn-out and burn-in of 59Ni and for uncertainties in neutron flux and spectra in the vicinity of the edge of the core.
Download or read book The Influence of Helium on Mechanical Properties of Model Austenitic Alloys Determined Using Sup 59 Ni Isotopic Tailoring and Fast Reactor Irradiation written by and published by . This book was released on 1991 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile testing on model Fe-Cr-Ni alloys removed from four discharges of the 59Ni isotopic doping experiment in FFTF indicates that helium/dpa ratios typical of fusion reactors do not produce changes in the yield strength or elongation that are significantly different from those at much lower helium generation rates. It also appears that tensile properties approach a saturation level that is dependent only on the final irradiation temperature, but not prior temperature history or thermomechanical starting condition. 14 refs., 4 figs., 1 tab.
Download or read book The Influence of Helium on Mechanical Properties of Model Austenitic Alloys Determined Using 59Ni Isotopic Tailoring and Fast Reactor Irradiation written by and published by . This book was released on 1991 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile testing on model Fe-Cr-Ni alloys removed from four discharges of the 59Ni isotopic doping experiment in FFTF indicates that helium/dpa ratios typical of fusion reactors do not produce changes in the yield strength or elongation that are significantly different from those at much lower helium generation rates. It also appears that tensile properties approach a saturation level that is dependent only on the final irradiation temperature, but not prior temperature history or thermomechanical starting condition. 14 refs., 4 figs., 1 tab.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1993 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Microstructural Evolution of Neutron Irradiated Fe Cr Ni Alloys at 495 C in Response to Changes in the Helium DPA Ratio written by FA. Garner and published by . This book was released on 1990 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: A series of three Fe-15Cr-XNi alloys in both annealed and cold worked conditions was irradiated in the fast flux test facility (FFTF) at 495°C to 14 dpa. The experiment was developed to determine the separate and synergistic effects of nickel and phosphorus content, cold work, and helium/dpa ratio. This experiment was conducted without introducing variations in displacement rate, a variable known to strongly influence microstructural evolution. Each alloy condition was irradiated in two variants, one with natural nickel and one enhanced with the 59Ni isotope. The latter variant produces helium/dpa ratios typical of fusion reactor spectra while the former yields a much lower level of helium. The results show that helium alters the microstructural evolution somewhat at 495°C, but its effect is relatively small compared to the influences of the other variables studied. Increases in starting dislocation density, nickel content, or phosphorus level all retard swelling temporarily while higher rates of helium generation usually, but not always, accelerate swelling. Phosphorus addition of 0.04 wt% not only decreased swelling but led to refinement of dislocation loop microstructure and stabilization of dislocation networks created by cold working. Phosphide precipitates did not form at this temperature and dose level.
Download or read book The Dependence of Helium Generation Rate on Nickel Content of Fe Cr Ni Alloys Irradiated at High Dpa Levels in Fast Reactors written by and published by . This book was released on 1997 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: With a few exceptions in the literature, it is generally accepted that it is nickel in Fe-Cr-Ni alloys that produces most of the transmutant helium and that the helium generation rate should scale linearly with the nickel content. Surprisingly, this assumption is based only on irradiations of pure nickel and has never been tested in an alloy series. There have also been no extensive tests of the predictions for helium production in alloys in various fast reactors spectra.
Download or read book The Consequences of Helium Production and Nickel Additions on Microstructural Development in Isotopically Tailored Ferritic Alloys written by DS. Gelles and published by . This book was released on 1999 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: A series of alloys have been made adding various isotopes of nickel in order to vary the production of helium during irradiation by a two step nuclear reaction in a mixed spectrum reactor. The alloys use a base composition of Fe-12Cr with an addition of 1.5% nickel, either in the form of 60Ni which produces no helium, 59Ni which produces helium at a rate of about 10 appm He/dpa, or natural nickel which provides an intermediate level of helium due to delayed development of 59Ni. Specimens were irradiated in the HFIR at Oak Ridge, TN to 7.5 dpa at 300 and 400°C. Microstructural examinations indicated that nickel additions promote precipitation in all alloys, but the effect appears to be much stronger at 400°C than at 300°C. There is sufficient dose by 7 dpa (and with 2 appm He) to initiate void swelling in ferritic/martensitic alloys. Little difference was found between response from 59Ni and natural nickel. Also, helium bubble development for high helium generation conditions appeared to be very different at 300 and 400°C. At 300°C, it appeared that high densities of bubbles formed whereas at 400°C, bubbles could not be identified, possibly because of the complexity of the microstructure, but more likely because helium accumulated at precipitate interfaces.
Download or read book Energy Research Abstracts written by and published by . This book was released on 1993 with total page 754 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Materials Transactions JIM written by and published by . This book was released on 1993-07 with total page 714 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fusion Energy Update written by and published by . This book was released on 1986 with total page 614 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Government Reports Annual Index written by and published by . This book was released on 1992 with total page 1730 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Consequences of Helium Production on Microstructural Development in Isotopically Tailored Ferritic Alloys written by and published by . This book was released on 1996 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: A series of alloys have been made adding various isotopes of nickel in order to vary the production of helium during irradiation by a two step nuclear reaction in a mixed spectrum reactor. The alloys use a base composition of Fe-12Cr with an addition of 1.5% nickel, either in the form of 6°Ni which produces no helium, 59Ni which produces helium at a rate of about 10 appm He/dpa, or natural nickel ({sup Nat}Ni) which provides an intermediate level of helium due to delayed development of 59Ni. Specimens were irradiated in the HFIR at Oak Ridge, TN to ≈7 dpa at 300 and 400°C. Microstructural examinations indicated that nickel additions promote precipitation in all alloys, but the effect appears to be much stronger at 400°C than at 300°C. There is sufficient dose by 7 dpa (and with 2 appm He) to initiate void swelling in ferritic/martensitic alloys. Little difference was found between response from 59Ni and {sup Nat}Ni. Also, helium bubble development for high helium generation conditions appeared to be very different at 300 and 400°C. At 300°C, it appeared that high densities of bubbles formed whereas at 400°C, bubbles could not be identified, possibly because of the complexity of the microstructure, but more likely because helium accumulated at precipitate interfaces.
Download or read book Materials Transactions written by and published by . This book was released on 1993-12 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt:
