Download or read book Frequency and Mean Stress Effects in High Cycle Fatigue of Ti 6A1 4V written by Ryan J. Morrissey and published by . This book was released on 1997 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this project was to extend past research on fatigue of Ti-6Al-4V into conditions which more closely reflect actual use conditions. This included testing at a range of frequencies (70, 400, 1800 Hz) to determine the effect of frequency on the fatigue strength. In addition, testing was performed at various stress ratios (0.1, 0.5, 0.8) to determine the effects of mean stress on the HCF performance of Ti-6A1-4V. This included an examination of the effects of cyclic and time-dependent strain accumulation on the fracture mode at high mean stresses. Frequency effects were observed at low stress ratios, resulting in higher fatigue strengths as the frequency increased. Possible causes include strain rate effects on dislocation motion, loss of active primary slip systems at high frequencies in hexagonal close-packed and body-centered cubic materials, and environmental damage. Results obtained at high mean stress show that the behavior of Ti-6A1-4V consists of a complex combination of fatigue, cyclic creep, and strain ratchetting. Fractographic analysis combined with cyclic creep studies were used to further define the mechanisms which led to the observed behavior.

Download or read book Frequency and Mean Stress Effects in High Cycle Fatigue of Ti 6A1 4V written by Ryan J. Morrissey and published by . This book was released on 1997 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Mean Stress Effects on the High Cycle Fatigue Limit Stress in Ti 6Al 4V written by T. Nicholas and published by . This book was released on 2003 with total page 17 pages. Available in PDF, EPUB and Kindle. Book excerpt: An investigation was undertaken to evaluate the effects of mean stress on the high cycle fatigue (HCF) limit stress under uniaxial loading. Tests were conducted at constant values of stress ratio, R (ratio of minimum to maximum stress), at frequencies from 20 to 70 Hz up to 107 cycles using a step-loading technique developed by the authors. Data were presented in the form of a Haigh (Modified Goodman) diagram as alternating stress against mean stress. Tests in the regime R

Download or read book High Cycle Fatigue written by Theodore Nicholas and published by Elsevier. This book was released on 2006-07-07 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dr Theodore Nicholas ran the High Cycle Fatigue Program for the US Air Force between 1995 and 2003 at Wright-Patterson Air Force Base, and is one of the world’s leading authorities on the subject, having authored over 250 papers in leading archival journals and books. Bringing his plethora of expertise to this book, Dr Nicholas discusses the subject of high cycle fatigue (HCF) from an engineering viewpoint in response to a series of HCF failures in the USAF and the concurrent realization that HCF failures in general were taking place universally in both civilian and military engines. Topic covered include: Constant life diagrams Fatigue limits under combined LCF and HCF Notch fatigue under HCF conditions Foreign object damage (FOD) Brings years of the Author's US Air Force experience in high cycle fatigue together in one text Discusses HCF in the context of recent international military and civilian engine failures

Download or read book Fatigue and Fracture Mechanics written by Walter G. Reuter and published by ASTM International. This book was released on 2002-12-31 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covering the whole of Asia and the Pacific region, this text provides both an analytic overview and specific data for each of the 60 countries. Introductory chapters cover regional issues, including: a regional review with the year's trends, developments and key events' analysis of the threat of terrorism in the region; the effects of deflation on the economy; the water crisis and its impact on the poor; and the successes and failures of micro-credit in the region.

Download or read book Fatique and Fracture Mechanics written by Gary R. Halford and published by ASTM International. This book was released on 2000 with total page 551 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fatigue Data Book written by ASM International and published by ASM International. This book was released on 1994-12-31 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fatigue of Structures and Materials written by J. Schijve and published by Springer Science & Business Media. This book was released on 2008-12-16 with total page 627 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue of structures and materials covers a wide scope of different topics. The purpose of the present book is to explain these topics, to indicate how they can be analyzed, and how this can contribute to the designing of fatigue resistant structures and to prevent structural fatigue problems in service. Chapter 1 gives a general survey of the topic with brief comments on the signi?cance of the aspects involved. This serves as a kind of a program for the following chapters. The central issues in this book are predictions of fatigue properties and designing against fatigue. These objectives cannot be realized without a physical and mechanical understanding of all relevant conditions. In Chapter 2 the book starts with basic concepts of what happens in the material of a structure under cyclic loads. It illustrates the large number of variables which can affect fatigue properties and it provides the essential background knowledge for subsequent chapters. Different subjects are presented in the following main parts: • Basic chapters on fatigue properties and predictions (Chapters 2–8) • Load spectra and fatigue under variable-amplitude loading (Chapters 9–11) • Fatigue tests and scatter (Chapters 12 and 13) • Special fatigue conditions (Chapters 14–17) • Fatigue of joints and structures (Chapters 18–20) • Fiber-metal laminates (Chapter 21) Each chapter presents a discussion of a speci?c subject.

Download or read book Fatigue Fracture and Residual Stresses written by Sharif Rahman and published by . This book was released on 1998 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fifty-one technical papers from the July 1998 Conference are organized into six sections which discuss probabilistic fracture mechanics, fracture of welds, finite elements and constraint effects on fracture, failure prediction, residual stresses, and pipe fracture. They present novel analytical and

Download or read book Fretting Fatigue written by David W. Hoeppner and published by ASTM International. This book was released on 2000 with total page 554 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume includes 36 of the 40 papers presented at the symposium, and a collection of six keynote papers providing background on the subject. Topics covered include parameter effects, environmental effects, crack nucleation, material and microstructural effects, damage analysis, fracture mechanic

Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1974 with total page 586 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Effects of a High Mean Stress on the High Cycle Fatigue Life of PWA 1480 and Correlation of Data by Linear written by and published by . This book was released on 19?? with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fatigue Performance of Laser Additive Manufactured Ti 6al 4V in Very High Cycle Fatigue Regime Up to 1E9 Cycles written by Eric Wycisk and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing technologies are in the process of establishing themselves as an alternative production technology to conventional manufacturing, such as casting or milling. Especially laser additive manufacturing (LAM) enables the production of metallic parts with mechanical properties comparable to conventionally manufactured components. Due to the high geometrical freedom in LAM, the technology enables the production of ultra-light weight designs, and therefore gains increasing importance in aircraft and space industry. The high quality standards of these industries demand predictability of material properties for static and dynamic load cases. However, fatigue properties especially in the very high cycle fatigue (VHCF) regime until 109 cycles have not been sufficiently determined yet. Therefore, this paper presents an analysis of fatigue properties of laser additive manufactured Ti-6Al-4V under cyclic tension-tension until 107 cycles and tension-compression load until 109 cycles. For the analysis of laser additive manufactured titanium alloy Ti-6Al-4V, Woehler fatigue tests under tension-tension and tension-compression were carried out in the high cycle and VHCF regime. Specimens in stress-relieved as well as hot-isostatic-pressed conditions were analyzed regarding crack initiation site, mean stress sensitivity, and overall fatigue performance. The determined fatigue properties show values in the range of conventionally manufactured Ti-6Al-4V with particularly good performance for hot-isostatic-pressed additive-manufactured material. For all conditions, the results show no conventional fatigue limit but a constant increase in fatigue life with decreasing loads. No effects of test frequency on life span could be determined. However, independently of testing principle, a shift of crack initiation from surface to internal initiation could be observed with increasing cycles to failure.

Download or read book Mean Stress Effects in Low Cycle Fatigue written by and published by . This book was released on 2000 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1990 with total page 740 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Computational Materials System Design written by Dongwon Shin and published by Springer. This book was released on 2017-11-10 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides state-of-the-art computational approaches for accelerating materials discovery, synthesis, and processing using thermodynamics and kinetics. The authors deliver an overview of current practical computational tools for materials design in the field. They describe ways to integrate thermodynamics and kinetics and how the two can supplement each other.

Download or read book Safety and Reliability of Complex Engineered Systems written by Luca Podofillini and published by CRC Press. This book was released on 2015-09-03 with total page 730 pages. Available in PDF, EPUB and Kindle. Book excerpt: Safety and Reliability of Complex Engineered Systems contains the Proceedings of the 25th European Safety and Reliability Conference, ESREL 2015, held 7-10 September 2015 in Zurich, Switzerland. It includes about 570 papers accepted for presentation at the conference. These contributions focus on theories and methods in the area of risk, safety and