Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System For Operating Pressures Up to and Including 5080 Psi 35 000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged titanium tube fittings on titanium and CRES tubing with flareless separable fitting for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35 000 kPa) maximum and an operating temperature range of 65 to +275 °F (54 to +135 °C).This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5959. The fitting operating pressure is based on the fitting thread pitch. Extra fine pitch for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Add Blue Anodize and Ink-Jet Options as Identification and Marking methods to 3.4.2.3 and 3.5.2, and correct the joint strength conversion values to Newton in Tables 3A and 3B.

Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System for Operating Pressures Up to and Including 5080 Psi 35000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for axially swaged titanium fittings on titanium, CRES, and aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35000 kPa) maximum. The operating temperature range for titanium tubing and CRES tubing is 65 to +275 °F (54 to +135 °C) and the operating temperature range for aluminum return system tubing is 65 to +225 °F (54 to +107 °C).This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5959. The flareless fitting operating pressure is based on the fitting thread pitch. Extra fine pitch is used for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less. Table 14 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Add performance requirements for aluminum tubing, class designation for tubing, update and correct existing text and figures.

Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System 5080 Psi 35 000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged titanium tube fittings on titanium tubing with flareless separable fitting for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35,000 kPa) maximum and an operating temperature range of -65 to +275 °F (-54 to +135 °C). This specification was prepared to provide the performance requirements for axially swaged, field attachable, 5080 psi, tube fittings.

Download or read book Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 Psi 10 340 KPa Maximum Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems including pneumatic, coolants, and fire extinguishers up to a maximum operating pressure of 1500 psig (10 340 kPa) and a maximum operating temperature range of 65 to +225 °F (54 to +107 °C).This specification covers a common aluminum fitting that may be used for a range of operating pressures up to 1500 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS6124. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. This specification is being prepared to provide the performance requirements for aluminum axially swaged, field attachable, 1500 psi, tube fittings.

Download or read book Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 Psi 10340 KPa Maximum Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems including pneumatic, coolants, and fire extinguishers up to a maximum operating pressure of 1500 psig (10340 kPa) and a maximum operating temperature range of -65 to +225 °F (-54 to +107 °C).This specification covers a common aluminum fitting that may be used for a range of operating pressures up to 1500 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS6124. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Change operating pressure requirements of size 24 from 500 to 600 psi (including proof and burst pressures), add vibration curves requirements to Tables 10 and 11 for size 24, add the new configuration part number AS6323 to Table 12, and add size 24 dimensions to some of the standards configurations.

Download or read book Fittings Tube Fluid System 3000 Psig 21 000 KPa Rated Pressure Externally Swaged Specification For written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10 500 kPa), and D (3000 psi or 21 000 kPa), and in temperature types I (65 to 160 °F or 55 to 70 °C), and II (65 to 275 °F or 55 to 135 °C) of AS2001.This specification covers a common Cres, titanium, and aluminum fittings that may be used for a range of operating pressures up to 3000 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5902. Table 10 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Complete update of the procurement specification to prepare for QPL listing of part standards listed in Table 10 including corrections of material specification numbers, tube materials, wall thicknesses in Table 7, description of back-up seal, and updating quality conformance plans.

Download or read book Aerospace Separable Tube Fittings for Fluid Systems for 24 0D Cones for Pressures Up to 3 000 Psi Or 21 000 KPa Procurement Specification Inch metric written by British Standards Institute Staff and published by . This book was released on 1914-11-30 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aircraft components, Hydraulic equipment, Fluid equipment components, Fluid equipment, Pipe fittings, Threads, Defects, Surface defects, Pressure, Grades (quality), Performance, Dimensions, Angles (geometry), Colour codes, Marking, Finishes, Classification systems, Test pressure, Bend testing, Leak tests, Stress corrosion, Corrosion tests, Mechanical testing, Pressure testing, Sampling methods, Quality assurance, Inspection, Approval testing, Quality control, Statistical quality control, Packaging, Test specimens

Download or read book FITTING ASSEMBLY UNION AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: UPDATING PART STANDARD WITH THE NEW CLASS "D" FOR USE ON ALUMINUM TUBING. THIS IS IN CONCURRENCE WITH AS5958 REV F PROJECT G3B16-09. /1/MATERIALS:CODE LETTER "T"RINGS - AMS4965 TITANIUM ALLOY, 6.0Al-4.0V SOLUTION HEAT TREATED AND AGED OR AMS4928 TITANIUM ALLOY 6.0AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT.BODY - AMS4928 TITANIUM ALLOY, 6.0Al-4.0V ANNEALED 2FINISH:TITANIUM - NONE /3/COATINGS/LUBRICANTS /16/: aNO SUFFIX CODE LETTER (1)RINGS - THE OUTER SURFACE SHALL HAVE A .125 INCH MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. PTFE COATING OR PAINT SHALL BE RESISTANT TO AS1241 FLUID WHEN USED. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. bSUFFIX CODE LETTER A (1)RINGS - NO BLUE PTFE COATING OR PAINT. THE WORD "BLUE" SHALL BE MARKED ON THE RING TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. cSUFFIX CODE LETTER B (1)RINGS - PARTIALLY (.125 INCH MINIMUM WIDTH) OR COMPLETELY ANODIZED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT, MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. /4/PROCUREMENT SPECIFICATION: AS5958 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LISTING FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE www.eAuditNet.com FOR CURRENT QPL ON-LINE. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. /7/FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. THE AFTER SWAGE ACCEPTABILITY LIMIT DIMENSION "Z" FOR EACH PORT SIZE IS DEFINED IN AS5959. 8SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. 9DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE ±.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE ±.50° UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003 TO .010 INCHES, UNLESS OTHERWISE SPECIFIED 10INTERPRETATION OF DRAWING PER ARP4296. /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/FOR JUMP SIZE FITTINGS, A TRANSITION DIAMETER WILL OCCUR IN THIS AREA. /13/DIMENSION A IS THE FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AND A1 IS THE FITTING BODY LENGTH BEFORE SWAGE. 14REVISION INDICATOR: A CHANGE BAR (%7c) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. /15/EXAMPLE OF PART NUMBER: /16/UNPAINTED RINGS "CODE A" WERE NEEDED TO PREVENT COATING/PAINT DEBRIS OF RINGS "NO CODE" IN CONTAMINATION SENSITIVE SYSTEMS. NO CODE LETTER AND CODE LETTER "A" PARTS ARE NOT RECOMMENDED FOR PROCUREMENT AFTER 03/31/2014 AND SHOULD BE REPLACED BY ANODIZED PARTS WITH CODE LETTER "B". /17/CLASS 1 - NO CODE IN PART NUMBER. PARTS ARE QUALIFIED FOR INSTALLATION ON TITANIUM AND CRES TUBINGCLASS 2 - CODE "D" IN PART NUMBER. PARTS ARE QUALIFIED FOR INSTALLATION ON TITANIUM, CRES, AND ALUMINUM TUBING.

Download or read book Aerospace Separable Tube Fittings for Fluid Systems for 24 0D Cones for Pressures Up to 3000 PSI Or 21000 KPa Procurement Specification Inch Metric written by British Standards Institute Staff and published by . This book was released on 2007-05-31 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aircraft components, Hydraulic equipment, Fluid equipment components, Fluid equipment, Pipe fittings, Threads, Defects, Surface defects, Pressure, Grades (quality), Performance, Dimensions, Angles (geometry), Colour codes, Marking, Finishes, Classification systems, Test pressure, Bend testing, Leak tests, Stress corrosion, Corrosion tests, Mechanical testing, Pressure testing, Sampling methods, Quality assurance, Inspection, Approval testing, Quality control, Statistical quality control, Packaging, Test specimens

Download or read book Aerospace Series Tube Fittings for Fluid Systems 5 080 Psi 35 000 KPa Qualification Specification written by British Standards Institute Staff and published by . This book was released on 1915-09-30 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: FLUID EQUIPMENT COMPONENTS, AIRCRAFT COMPONENTS, FLUID EQUIPMENT, PIPE FITTINGS, HYDRAULIC EQUIPMENT, PERFORMANCE, INSPECTION, APPROVAL TESTING, QUALITY CONTROL, SPECIMEN PREPARATION, MECHANICAL TESTING, AIR TRANSPORT ENGINEERING, DESIGN, PRODUCTION, QUALIFICATION APPROVAL, QUALITY ASSURANCE

Download or read book FITTING ASSEMBLY TEE AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS STANDARD WAS PREPARED TO PROVIDE AN ENVELOPE REQUIREMENTS FOR AN AXIALLY SWAGED, FIELD ATTACHABLE, 5000 PSI, TUBE FITTING. /1/MATERIALS: CODE LETTER "T" RINGS-AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0 AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT. BODY-AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED 2FINISH: TITANIUM-NONE REQUIRED /3/COATINGS/LUBRICANTS: RINGS-THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED. BODY-SOLID FILM LUBRICANT PER AS5272, TYPE I OR II, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. /4/ALL PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE HTTP:WWW.PRI.SAE.ORG/QPL/AS5958.PDF FOR CURRENT QPL ONLINE. PRIOR TO ISSUANCE OF THE PRI-QPL, USERS ARE ADVISED TO CONTROL SOURCE APPROVALS BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON ONE OF THE THREE RINGS IN THE AREA SHOWN. 7FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. 8SURFACE TEXTURE SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS. ASME Y14.1 AND THE SYMBOLS IN ACCORDANCE WITH ASME14.36M. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 uin Ra AND THE MAXIMUM FORGED SURFACES SHALL BE 250 uin Ra. 9DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS, ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE +/-.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE +/-0.50 DEGREES UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED 10INTREPRETATION OF DRAWING PER AS4296 /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/.030 MIN RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS. /13/

Download or read book Fittings Tube Fluid System 3000 4000 Psig Rated Pressure Externally Swaged Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube fittings for use in hydraulic and other aerospace fluid systems in temperature range of -65 to 275 °F.

Download or read book FITTING ASSEMBLY ELBOW 45 AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS STANDARD WAS PREPARED TO PROVIDE AN ENVELOPE REQUIREMENTS FOR AN AXIALLY SWAGED, FIELD ATTACHABLE, 5000 PSI, TUBE FITTING. /1/MATERIALS: CODE LETTER "T" RINGS-AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0 AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT. BODY-AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED 2FINISH: TITANIUM-NONE REQUIRED /3/COATINGS/LUBRICANTS: RINGS-THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED. BODY-SOLID FILM LUBRICANT PER AS5272. TYPE I OR II. PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. /4/ALL PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE HTTP:WWW.PRI.SAE.ORG/QPL/AS5958.PDF FOR CURRENT QPL ONLINE. PRIOR TO ISSUANCE OF THE PRI-QPL. USERS ARE ADVISED TO CONTROL SOURCE APPROVALS BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. 7FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. 8SURFACE TEXTURE SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS. ASME Y14.1 AND THE SYMBOLS IN ACCORDANCE WITH ASME14.36M. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 uin Ra AND THE MAXIMUM FORGED SURFACES SHALL BE 250 uin Ra. 9DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS. ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE +/-.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE +/-0.50 DEGREES UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED 10INTREPRETATION OF DRAWING PER AS4296 /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/.030 MIN RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS. /13/

Download or read book FITTING ASSEMBLY STRAIGHT FEMALE FLARELESS AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS STANDARD WAS PREPARED TO PROVIDE AN ENVELOPE REQUIREMENTS FOR AN AXIALLY SWAGED, FIELD ATTACHABLE, 5000 PSI, TUBE FITTING. /1/MATERIALS: CODE LETTER "T" RING-AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT. BODY-AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED NUT-AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION TREATED WIRE-AMS 5637 STEEL, CORROSION RESISTANT, 18Cr-9.0Ni (UNS 30302) SOLUTION TREATED AND COLD DRAWN 125 KSI TENSILE STRENGTH -AMS 5685 STEEL, CORROSION RESISTANT, SAFETY WIRE 18Cr-11.5 Ni, 305 WIRE, SOLUTION TREATED, COLD FINISHED -ASTM A 580 STEEL, CORROSION RESISTANT, WIRE, 302 OR 305 CONDITION A 2FINISH: TITANIUM-NONE REQUIRED CRES-PASSIVATION PER AMS 2700 /3/COATINGS/LUBRICANTS: RINGS-THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED. BODY-SOLID FILM LUBRICANT PER AS5272, TYPE I OR II, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. NUT-LUBRICATE ID THREADS AND WIRE GROOVE LOAD BEARING SHOULDER OR MATING WIRE GROOVE LOAD BEARING SHOULDER WITH SOLID FILM LUBRICANT PER AS5272, TYPE 1 OR TYPE 2. /4/ALL PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE HTTP:WWW.PRI.SAE.ORG/QPL/AS5958.PDF FOR CURRENT QPL ONLINE. PRIOR TO ISSUANCE OF THE PRI-QPL, USERS ARE ADVISED TO CONTROL SOURCE APPROVALS BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON RING IN THE AREA SHOWN. 7FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. 8SURFACE TEXTURE SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS. ASME Y14.1 AND THE SYMBOLS IN ACCORDANCE WITH ASME14.36M. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 uin Ra AND THE MAXIMUM FORGED SURFACES SHALL BE 250 uin Ra. 9DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS, ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE +/-.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE +/-0.30 DEGREES UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED 10INTREPRETATION OF DRAWING PER AS4296 /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/FITTINGS SHALL MATE WITH AS5827-(SIZE). STANDARD COUPLING NUTS SHALL BE IN ACCORDANCE WITH OR FUNCTIONALLY EQUIVALENT TO AS4370TXX EXCEPT FOR THREAD PITCH. /13/

Download or read book Fittings 24 Cone Flareless Fluid Connection 3000 Psi written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2019 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 24° cone flareless fluid connection fittings and nuts, internally or externally swaged, preset, or welded sleeves for use in aircraft fluid systems at nominal operating pressures up to and including 3000 psi. Revision G clarifies: defect descriptions for aluminum material finishes and test requirements for high purity aluminum (HPA) coating to eliminate redundancy with reference documents; qualification approval between 4130 and 15-5PH materials; equivalent materials for PRI QPL lists; pressure rating for size 16 aluminum tubing; provided reference for defect limits on unmachined surfaces. Lists of flareless fitting end standards is made consistent throughout. Adds single point machining requirement on flareless ends. Adds 12 month periodic test interval. Provides lubrication allowance for pneumatic test of similar materials.

Download or read book FITTING ASSEMBLY ELBOW 90 AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS STANDARD WAS PREPARED TO PROVIDE AN ENVELOPE REQUIREMENTS FOR AN AXIALLY SWAGED, FIELD ATTACHABLE, 5000 PSI, TUBE FITTING. /1/MATERIALS: CODE LETTER "T" RINGS-AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0 AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT. BODY-AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED 2FINISH: TITANIUM-NONE REQUIRED /3/COATINGS/LUBRICANTS: RINGS-THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED. BODY-SOLID FILM LUBRICANT PER AS5272, TYPE I OR II, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. /4/ALL PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE HTTP:WWW.PRI.SAE.ORG/QPL/AS5958.PDF FOR CURRENT QPL ONLINE. PRIOR TO ISSUANCE OF THE PRI-QPL, USERS ARE ADVISED TO CONTROL SOURCE APPROVALS BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. 7FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. 8SURFACE TEXTURE SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS. ASME Y14.1 AND THE SYMBOLS IN ACCORDANCE WITH ASME14.36M. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 uin Ra AND THE MAXIMUM FORGED SURFACES SHALL BE 250 uin Ra. 9DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS, ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE +/-.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE +/-0.50 DEGREES UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED 10INTREPRETATION OF DRAWING PER AS4296 /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/.030 MIN RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS. /13/

Download or read book Fittings 24 Degree Cone Flareless Fluid Connection 3000 Psi written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 24 degree cone flareless fluid connection fittings and nuts, internally or externally swaged, preset, or welded sleeves for use in aircraft fluid systems at nominal operating pressures up to and including 3000 psi. Note 3.3.2, sub-note 4 added to address acceptance of excessive roughness of thread crests due to thread rolling process. NAS1760 added to note 3.7.5. Specification number typo corrected in Table 12.