Download or read book Experimental Study on Bond Behaviour of CFRP Sheets Externally Bonded to Reinforced Concrete written by Emmanuella Atunbi and published by . This book was released on 2018 with total page 195 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fiber reinforced polymers (FRP) have become widely used in retrofitting existing reinforced concrete (RC) structures because of their high strength and stiffness-to-weight ratio. An important aspect in the design of this composite element is determining the bond behaviour of the FRP sheet-to-concrete interface. Previous studies have involved the use of conventional instrumentation (typically strain gauges) that provide limited data to work with. This study presents an experimental investigation to determine the effect of bond length and stress on the bond behaviour of FRP-to-concrete interface under static loads using a digital image correlation (DIC) technique. Twelve double lap shear specimens bonded with carbon fiber reinforced polymer (CFRP) sheets were tested with varying bond lengths. Development length, longitudinal strains and bond stress and slip relationships were obtained and compared with values computed from existing models. Comprehensive results were obtained from the DIC technique which allowed for proper monitoring of the progression of failure and the effect of shear lag on the distribution of stresses in the FRP sheet.
Download or read book Numerical Modelling of CFRP Sheets Externally Bonded to Reinforced Concrete written by Adam John Lawlor and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre reinforced polymers (FRP) are becoming a commonly used material in retrofitting and rehabilitating deteriorating concrete structures. Aside from its high strength, FRP is a lightweight, non-corrosive, and relatively cheap alternative to traditional rehabilitation methods. One of the major components of FRP externally bonded to reinforced concrete is the bond and its behaviour at the FRP-concrete interface. Previous studies have investigated debonding of FRP sheets externally bonded to reinforced concrete through experimental testing as well as finite element modelling. This project presents the numerical modelling of CFRP sheets externally bonded to reinforced concrete. Using the finite element analysis software ABAQUS, three specimens of varying bond lengths subjected to double lap shear were modelled and analyzed. The results were discussed and compared to an experimental study previously performed.
Download or read book Externally Bonded FRP Reinforcement for RC Structures written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2001-01-01 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: In December 1996, the then CEB established a Task Group with the main objective to elaborate design guidelines for the use of FRP reinforcement in accordance with the design format of the CEB-FIP Model Code and Eurocode2. With the merger of CEB and FIP into fib in 1998, this Task Group became fib TG 9.3 FRP Reinforcement for concrete structures in Commission 9 Reinforcing and Prestressing Materials and Systems. The Task Group consists of about 60 members, representing most European universities, research institutes and industrial companies working in the field of advanced composite reinforcement for concrete structures, as well as corresponding members from Canada, Japan and USA. Meetings are held twice a year and on the research level its work is supported by the EU TMR (European Union Training and Mobility of Researchers) Network "ConFibreCrete”. The work of fib TG 9.3 is performed by five working parties (WP): Material Testing and Characterization (MT&C) Reinforced Concrete (RC) Prestressed Concrete (PC) Externally Bonded Reinforcement (EBR) Marketing and Applications (M&A) This technical report constitutes the work conducted as of to date by the EBR party. This bulletin gives detailed design guidelines on the use of FRP EBR, the practical execution and the quality control, based on the current expertise and state-of-the-art knowledge of the task group members. It is regarded as a progress report since it is not the aim of this report to cover all aspects of RC strengthening with composites. Instead, it focuses on those aspects that form the majority of the design problems. several of the topics presented are subject of ongoing research and development, and the details of some modelling approaches may be subject to future revisions. as knowledge in this field is advancing rapidly, the work of the EBR WP will continue. Inspite of this limit in scope, considerable effort has been made to present a bulletin that is today’s state-of-art in the area of strengthening of concrete structures by means of externally bonded FRP reinforcement.
Download or read book ACI 440 2R 17 Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures written by ACI Committee 440 and published by . This book was released on 2017-04-27 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Strengthening of Reinforced Concrete Structures written by L C Hollaway and published by Elsevier. This book was released on 1999-03-05 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: The in situ rehabilitation or upgrading of reinforced concrete members using bonded steel plates is an effective, convenient and economic method of improving structural performance. However, disadvantages inherent in the use of steel have stimulated research into the possibility of using fibre reinforced polymer (FRP) materials in its place, providing a non-corrosive, more versatile strengthening system. This book presents a detailed study of the flexural strengthening of reinforced and prestressed concrete members using fibre reinforces polymer composite plates. It is based to a large extent on material developed or provided by the consortium which studied the technology of plate bonding to upgrade structural units using carbon fibre / polymer composite materials. The research and trial tests were undertaken as part of the ROBUST project, one of several ventures in the UK Government's DTI-LINK Structural Composites Programme. The book has been designed for practising structural and civil engineers seeking to understand the principles and design technology of plate bonding, and for final year undergraduate and postgraduate engineers studying the principles of highway and bridge engineering and structural engineering. Detailed study of the flexural strengthening of reinforced and prestressed concrete members using fibre reinforced polymer composites Contains in-depth case histories
Download or read book Fibre Reinforced Polymer Reinforcement for Concrete Structures written by Kiang Hwee Tan and published by World Scientific. This book was released on 2003 with total page 1526 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre-reinforced polymer (FRP) reinforcement has been used in construction as either internal or external reinforcement for concrete structures in the past decade. This book provides the latest research findings related to the development, design and application of FRP reinforcement in new construction and rehabilitation works. The topics include FRP properties and bond behaviour, externally bonded reinforcement for flexure, shear and confinement, FRP structural shapes, durability, member behaviour under sustained loads, fatigue loads and blast loads, prestressed FRP tendons, structural strengthening applications, case studies, and codes and standards.
Download or read book Retrofitting of Concrete Structures by Externally Bonded FRPs With Emphasis on Seismic Applications written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2006-01-01 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 35 is the first bulletin to publish documentation from an fib short course. These courses are held worldwide and cover advanced knowledge of structural concrete in general, or specific topics. They are organized by fib and given by internationally recognized experts in fib, often supplemented with local experts active in fib. They are based on the knowledge and expertise from fib's ten Commissions and nearly fifty Task Groups. fib Bulletin 35 presents the course materials developed for the short course "Retrofitting of Concrete Structures through Externally Bonded FRP, with emphasis on Seismic Applications", given in Ankara and Istanbul in June 2005. The course drew on expertise both from outside Turkey and from the large pool of local experts on this subject. In most countries of the world, the building stock is ageing and needs continuous maintenance or repair. Moreover, the majority of existing constructions are deficient in the light of current knowledge and design codes. The problem of structural deficiency of existing constructions is especially acute in seismic regions, as, even there, seismic design of structures is relatively recent. The direct and indirect costs of demolition and reconstruction of structurally deficient constructions are often prohibitive; furthermore they entail a substantial waste of natural resources and energy. Therefore, structural retrofitting is becoming increasingly widespread throughout the world. Externally bonded Fibre Reinforced Polymers (FRPs) are rapidly becoming the technique of choice for structural retrofitting. They are cleaner and easier to apply than conventional retrofitting techniques, reduce disruption to the occupancy and operation of the facility, do not generate debris or waste, and reduce health and accident hazards at the construction site as well as noise and air pollution in the surroundings. fib Bulletin 35 gives state-of-the-art coverage of retrofitting through FRPs and presents relevant provisions from three recent standardisation milestones: EN 1998-3:2005 "Eurocode 8: Design of structures for earthquake resistance - Part 3: Assessment and retrofitting of buildings", the 2005 Draft of the Turkish seismic design code, and the Italian regulatory document CNR-DT 200/04, "Instructions for Design, Execution and Control of Strengthening Interventions by Means of Fibre-Reinforced Composites" (2004).
Download or read book Fibre reinforced Polymer Reinforcement For Concrete Structures In 2 Volumes Proceedings Of The Sixth International Symposium On Frp Reinforcement For Concrete Structures Frprcs 6 written by Kiang Hwee Tan and published by World Scientific. This book was released on 2003-06-20 with total page 1526 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre-reinforced polymer (FRP) reinforcement has been used in construction as either internal or external reinforcement for concrete structures in the past decade. This book provides the latest research findings related to the development, design and application of FRP reinforcement in new construction and rehabilitation works. The topics include FRP properties and bond behaviour, externally bonded reinforcement for flexure, shear and confinement, FRP structural shapes, durability, member behaviour under sustained loads, fatigue loads and blast loads, prestressed FRP tendons, structural strengthening applications, case studies, and codes and standards.
Download or read book Non Metallic FRP Reinforcement for Concrete Structures written by L. Taerwe and published by CRC Press. This book was released on 1995-08-03 with total page 738 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dealing with a wide range of non-metallic materials, this book opens up possibilities of lighter, more durable structures. With contributions from leading international researchers and design engineers, it provides a complete overview of current knowledge on the subject.
Download or read book Study of the Flexural Behavior of Reinforced Concrete Beams Strengthened by Externally Bonded Fiber Reinforced Polymeric FRP Laminates written by María del Mar López Acevedo and published by . This book was released on 2000 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book FRP written by J. G. Teng and published by John Wiley & Sons. This book was released on 2002 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre-reinforced polymer (FRP) composites are used to strengthen reinforced concrete (RC) structures. A large amount of research now exists on this. This book brings together all existing research into one volume.
Download or read book Building Code Requirements for Structural Concrete ACI 318 08 and Commentary written by ACI Committee 318 and published by American Concrete Institute. This book was released on 2008 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: The quality and testing of materials used in construction are covered by reference to the appropriate ASTM standard specifications. Welding of reinforcement is covered by reference to the appropriate AWS standard. Uses of the Code include adoption by reference in general building codes, and earlier editions have been widely used in this manner. The Code is written in a format that allows such reference without change to its language. Therefore, background details or suggestions for carrying out the requirements or intent of the Code portion cannot be included. The Commentary is provided for this purpose. Some of the considerations of the committee in developing the Code portion are discussed within the Commentary, with emphasis given to the explanation of new or revised provisions. Much of the research data referenced in preparing the Code is cited for the user desiring to study individual questions in greater detail. Other documents that provide suggestions for carrying out the requirements of the Code are also cited.
Download or read book Strengthening Design of Reinforced Concrete with FRP written by Hayder A. Rasheed and published by CRC Press. This book was released on 2014-12-16 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: Strengthening Design of Reinforced Concrete with FRP establishes the art and science of strengthening design of reinforced concrete with fiber-reinforced polymer (FRP) beyond the abstract nature of the design guidelines from Canada (ISIS Canada 2001), Europe (FIB Task Group 9.3 2001), and the United States (ACI 440.2R-08). Evolved from thorough cla
Download or read book Bond Behavior of Fiber Reinforced Polymer Laminates to Concrete Subjected to Varied Surface Preparation written by Jason Michael Jeffries and published by . This book was released on 2004 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The purpose of this investigation is to study the effect of surface roughness on the bond between Carbon Fiber Reinforced Polymer (CFRP) sheets and concrete. The experimental investigation was conducted in order to determine the effects of various methods of surface preparation to produce varying levels of surface roughness, and concrete strength."--Abstract, p. iii.
Download or read book Design Procedures for the Use of Composites in Strengthening of Reinforced Concrete Structures written by Carlo Pellegrino and published by Springer. This book was released on 2015-08-25 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book analyses the current knowledge on structural behaviour of RC elements and structures strengthened with composite materials (experimental, analytical and numerical approaches for EBR and NSM), particularly in relation to the above topics, and the comparison of the predictions of the current available codes/recommendations/guidelines with selected experimental results. The book shows possible critical issues (discrepancies, lacunae, relevant parameters, test procedures, etc.) related to current code predictions or to evaluate their reliability, in order to develop more uniform methods and basic rules for design and control of FRP strengthened RC structures. General problems/critical issues are clarified on the basis of the actual experiences, detect discrepancies in existing codes, lacunae in knowledge and, concerning these identified subjects, provide proposals for improvements. The book will help to contribute to promote and consolidate a more qualified and conscious approach towards rehabilitation and strengthening existing RC structures with composites and their possible monitoring.
Download or read book 10th International Conference on FRP Composites in Civil Engineering written by Alper Ilki and published by Springer Nature. This book was released on 2021-11-26 with total page 2516 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume highlights the latest advances, innovations, and applications in the field of FRP composites and structures, as presented by leading international researchers and engineers at the 10th International Conference on Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering (CICE), held in Istanbul, Turkey on December 8-10, 2021. It covers a diverse range of topics such as All FRP structures; Bond and interfacial stresses; Concrete-filled FRP tubular members; Concrete structures reinforced or pre-stressed with FRP; Confinement; Design issues/guidelines; Durability and long-term performance; Fire, impact and blast loading; FRP as internal reinforcement; Hybrid structures of FRP and other materials; Materials and products; Seismic retrofit of structures; Strengthening of concrete, steel, masonry and timber structures; and Testing. The contributions, which were selected by means of a rigorous international peer-review process, present a wealth of exciting ideas that will open novel research directions and foster multidisciplinary collaboration among different specialists.
Download or read book Structures Strengthened with Bonded Composites written by Zhishen Wu and published by Woodhead Publishing. This book was released on 2020-07-15 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structures Strengthened with Bonded Composites presents a comprehensive resource on the strengthening of concrete, reinforced and prestressed concrete, masonry, steel and other composite structures using externally-bonded FRP composites. The book emphasizes a systematic and fundamental investigation on bonding and debonding behavior of the FRP-concrete interface and structural performances of FRP-strengthened structures with a combination of experimental, theoretical and numerical studies. This book will appeal to all those concerned with strengthening and retrofitting of existing structures from the effect of additional anticipated loads in the civil sector. Discusses the FRP strengthening of different types of structures, including bridges, tunnels, buildings, historic structures and underwater constructions Establishes a systematic theory on interfacial fracture mechanics and clarifies different debonding mechanisms Describes design methods and makes comparison of design considerations and methods among different countries Presents temperature and fatigue effects and long-term behavior for different strengthening methods
