Download or read book Experimental Investigation of DME Assisted Gasoline CAI Combustion with Re breathing Valve Strategy written by Kangwoo Seo and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Investigation of Gasoline di methyl Ether Dual Fuel CAI Combustion with Internal EGR written by Haofan Zhang and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A new dual fuel Controlled Auto-Ignition (CA!) combustion concept was proposed and researched for lower exhaust emissions and better fuel economy. The concept takes the advantage of the complementary physical and chemical properties of high octane number gasoline and high cetane number Di-Methyl Ether (DME) to organize the combustion process. Homogeneous gasoline/air mixture is utilized as the main combustible charge, which is realised by a low-cost Port Fuel Injection (PFI) system. Pressurised DME is directly injected into cylinder via a commercial Gasoline Direct Injection (GDI) injector. Flexible DME injection strategies are employed to realise the controlled auto ignition of the premixed charge. The engine is operated at Wide Open Throttle (WOT) in the entire operating region in order to minimize the intake pumping loss. Engine load is controlled by varying the amount of internal Exhaust Gas Recirculation (iEGR) which is achieved and adjusted by Positive Valve Overlap (PVO) and/or exhaust back pressure, and exhaust re- breathing method. The premixed mixture can be of either stoichiometric air/fuel ratio or fuel lean mixture and is heated and diluted by recycled exhaust gases. The use of internal EGR is considered as a very effective method to initiate CAI combustion due to its heating effect and moderation of the heat release rate by its dilution effect. In addition, the new combustion concept is compared to conventional SI combustion. The results indicate that the new combustion concept has potential for high efficiency, low emissions, enlargement of the engine operational region and flexible control of CAI combustion.

Download or read book HCCI and CAI Engines for the Automotive Industry written by Hua Zhao and published by CRC Press. This book was released on 2007-09-10 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.

Download or read book Automotive Spark Ignited Direct Injection Gasoline Engines written by F. Zhao and published by Elsevier. This book was released on 2000-02-08 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: The process of fuel injection, spray atomization and vaporization, charge cooling, mixture preparation and the control of in-cylinder air motion are all being actively researched and this work is reviewed in detail and analyzed. The new technologies such as high-pressure, common-rail, gasoline injection systems and swirl-atomizing gasoline fuel injections are discussed in detail, as these technologies, along with computer control capabilities, have enabled the current new examination of an old objective; the direct-injection, stratified-charge (DISC), gasoline engine. The prior work on DISC engines that is relevant to current GDI engine development is also reviewed and discussed. The fuel economy and emission data for actual engine configurations have been obtained and assembled for all of the available GDI literature, and are reviewed and discussed in detail. The types of GDI engines are arranged in four classifications of decreasing complexity, and the advantages and disadvantages of each class are noted and explained. Emphasis is placed upon consensus trends and conclusions that are evident when taken as a whole; thus the GDI researcher is informed regarding the degree to which engine volumetric efficiency and compression ratio can be increased under optimized conditions, and as to the extent to which unburned hydrocarbon (UBHC), NOx and particulate emissions can be minimized for specific combustion strategies. The critical area of GDI fuel injector deposits and the associated effect on spray geometry and engine performance degradation are reviewed, and important system guidelines for minimizing deposition rates and deposit effects are presented. The capabilities and limitations of emission control techniques and after treatment hardware are reviewed in depth, and a compilation and discussion of areas of consensus on attaining European, Japanese and North American emission standards presented. All known research, prototype and production GDI engines worldwide are reviewed as to performance, emissions and fuel economy advantages, and for areas requiring further development. The engine schematics, control diagrams and specifications are compiled, and the emission control strategies are illustrated and discussed. The influence of lean-NOx catalysts on the development of late-injection, stratified-charge GDI engines is reviewed, and the relative merits of lean-burn, homogeneous, direct-injection engines as an option requiring less control complexity are analyzed.

Download or read book Characteristics and Control of Low Temperature Combustion Engines written by Rakesh Kumar Maurya and published by Springer. This book was released on 2017-11-03 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with novel advanced engine combustion technologies having potential of high fuel conversion efficiency along with ultralow NOx and particulate matter (PM) emissions. It offers insight into advanced combustion modes for efficient utilization of gasoline like fuels. Fundamentals of various advanced low temperature combustion (LTC) systems such as HCCI, PCCI, PPC and RCCI engines and their fuel quality requirements are also discussed. Detailed performance, combustion and emissions characteristics of futuristic engine technologies such as PPC and RCCI employing conventional as well as alternative fuels are analyzed and discussed. Special emphasis is placed on soot particle number emission characterization, high load limiting constraints, and fuel effects on combustion characteristics in LTC engines. For closed loop combustion control of LTC engines, sensors, actuators and control strategies are also discussed. The book should prove useful to a broad audience, including graduate students, researchers, and professionals Offers novel technologies for improved and efficient utilization of gasoline like fuels; Deals with most advanced and futuristic engine combustion modes such as PPC and RCCI; Comprehensible presentation of the performance, combustion and emissions characteristics of low temperature combustion (LTC) engines; Deals with closed loop combustion control of advanced LTC engines; State-of-the-art technology book that concisely summarizes the recent advancements in LTC technology. .

Download or read book Design and Development of Heavy Duty Diesel Engines written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on 2019-11-05 with total page 914 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended to serve as a comprehensive reference on the design and development of diesel engines. It talks about combustion and gas exchange processes with important references to emissions and fuel consumption and descriptions of the design of various parts of an engine, its coolants and lubricants, and emission control and optimization techniques. Some of the topics covered are turbocharging and supercharging, noise and vibrational control, emission and combustion control, and the future of heavy duty diesel engines. This volume will be of interest to researchers and professionals working in this area.

Download or read book Cleaner Combustion written by Frédérique Battin-Leclerc and published by Springer Science & Business Media. This book was released on 2013-09-06 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: This overview compiles the on-going research in Europe to enlarge and deepen the understanding of the reaction mechanisms and pathways associated with the combustion of an increased range of fuels. Focus is given to the formation of a large number of hazardous minor pollutants and the inability of current combustion models to predict the formation of minor products such as alkenes, dienes, aromatics, aldehydes and soot nano-particles which have a deleterious impact on both the environment and on human health. Cleaner Combustion describes, at a fundamental level, the reactive chemistry of minor pollutants within extensively validated detailed mechanisms for traditional fuels, but also innovative surrogates, describing the complex chemistry of new environmentally important bio-fuels. Divided into five sections, a broad yet detailed coverage of related research is provided. Beginning with the development of detailed kinetic mechanisms, chapters go on to explore techniques to obtain reliable experimental data, soot and polycyclic aromatic hydrocarbons, mechanism reduction and uncertainty analysis, and elementary reactions. This comprehensive coverage of current research provides a solid foundation for researchers, managers, policy makers and industry operators working in or developing this innovative and globally relevant field.

Download or read book Review of the 21st Century Truck Partnership written by National Research Council and published by National Academies Press. This book was released on 2008-10-19 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 21st Century Truck Partnership (21CTP), a cooperative research and development partnership formed by four federal agencies with 15 industrial partners, was launched in the year 2000 with high hopes that it would dramatically advance the technologies used in trucks and buses, yielding a cleaner, safer, more efficient generation of vehicles. Review of the 21st Century Truck Partnership critically examines and comments on the overall adequacy and balance of the 21CTP. The book reviews how well the program has accomplished its goals, evaluates progress in the program, and makes recommendations to improve the likelihood of the Partnership meeting its goals. Key recommendations of the book include that the 21CTP should be continued, but the future program should be revised and better balanced. A clearer goal setting strategy should be developed, and the goals should be clearly stated in measurable engineering terms and reviewed periodically so as to be based on the available funds.

Download or read book Advanced Combustion Techniques and Engine Technologies for the Automotive Sector written by Akhilendra Pratap Singh and published by Springer Nature. This book was released on 2019-10-10 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the recent advances in combustion strategies and engine technologies, with specific reference to the automotive sector. Chapters discuss the advanced combustion technologies, such as gasoline direct ignition (GDI), spark assisted compression ignition (SACI), gasoline compression ignition (GCI), etc., which are the future of the automotive sector. Emphasis is given to technologies which have the potential for utilization of alternative fuels as well as emission reduction. One special section includes a few chapters for methanol utilization in two-wheelers and four wheelers. The book will serve as a valuable resource for academic researchers and professional automotive engineers alike.

Download or read book Gaseous Carbon Waste Streams Utilization written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2019-02-22 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the quest to mitigate the buildup of greenhouse gases in Earth's atmosphere, researchers and policymakers have increasingly turned their attention to techniques for capturing greenhouse gases such as carbon dioxide and methane, either from the locations where they are emitted or directly from the atmosphere. Once captured, these gases can be stored or put to use. While both carbon storage and carbon utilization have costs, utilization offers the opportunity to recover some of the cost and even generate economic value. While current carbon utilization projects operate at a relatively small scale, some estimates suggest the market for waste carbon-derived products could grow to hundreds of billions of dollars within a few decades, utilizing several thousand teragrams of waste carbon gases per year. Gaseous Carbon Waste Streams Utilization: Status and Research Needs assesses research and development needs relevant to understanding and improving the commercial viability of waste carbon utilization technologies and defines a research agenda to address key challenges. The report is intended to help inform decision making surrounding the development and deployment of waste carbon utilization technologies under a variety of circumstances, whether motivated by a goal to improve processes for making carbon-based products, to generate revenue, or to achieve environmental goals.

Download or read book Introduction to Internal Combustion Engines written by Richard Stone and published by Bloomsbury Publishing. This book was released on 2017-09-16 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: Now in its fourth edition, this textbook remains the indispensable text to guide readers through automotive or mechanical engineering, both at university and beyond. Thoroughly updated, clear, comprehensive and well-illustrated, with a wealth of worked examples and problems, its combination of theory and applied practice aids in the understanding of internal combustion engines, from thermodynamics and combustion to fluid mechanics and materials science. This textbook is aimed at third year undergraduate or postgraduate students on mechanical or automotive engineering degrees. New to this Edition: - Fully updated for changes in technology in this fast-moving area - New material on direct injection spark engines, supercharging and renewable fuels - Solutions manual online for lecturers

Download or read book Micro and Nanomanufacturing Volume II written by Mark J. Jackson and published by Springer. This book was released on 2017-10-28 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive treatment of micro and nanofabrication techniques, and applies established and research laboratory manufacturing techniques to a wide variety of materials. It is a companion volume to “Micro and Nanomanufacturing” (2007) and covers new topics such as aligned nanowire growth, molecular dynamics simulation of nanomaterials, atomic force microscopy for microbial cell surfaces, 3D printing of pharmaceuticals, microvascular coaptation methods, and more. The chapters also cover a wide variety of applications in areas such as surgery, auto components, living cell detection, dentistry, nanoparticles in medicine, and aerospace components. This is an ideal text for professionals working in the field, and for graduate students in micro and nanomanufacturing courses.

Download or read book Diesel Engine System Design written by Qianfan Xin and published by Elsevier. This book was released on 2011-05-26 with total page 1087 pages. Available in PDF, EPUB and Kindle. Book excerpt: Diesel Engine System Design links everything diesel engineers need to know about engine performance and system design in order for them to master all the essential topics quickly and to solve practical design problems. Based on the author's unique experience in the field, it enables engineers to come up with an appropriate specification at an early stage in the product development cycle. - Links everything diesel engineers need to know about engine performance and system design featuring essential topics and techniques to solve practical design problems - Focuses on engine performance and system integration including important approaches for modelling and analysis - Explores fundamental concepts and generic techniques in diesel engine system design incorporating durability, reliability and optimization theories

Download or read book Dorland s Dictionary of Medical Acronyms and Abbreviations written by Dorland and published by Elsevier Health Sciences. This book was released on 2015-07-24 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: Medical acronyms and abbreviations offer convenience, but those countless shortcuts can often be confusing. Now a part of the popular Dorland's suite of products, this reference features thousands of terms from across various medical specialties. Its alphabetical arrangement makes for quick reference, and expanded coverage of symbols ensures they are easier to find. Effective communication plays an important role in all medical settings, so turn to this trusted volume for nearly any medical abbreviation you might encounter. - Symbols section makes it easier to locate unusual or seldom-used symbols. - Convenient alphabetical format allows you to find the entry you need more intuitively. - More than 90,000 entries and definitions. - Many new and updated entries including terminology in expanding specialties, such as Nursing; Physical, Occupational, and Speech Therapies; Transcription and Coding; Computer and Technical Fields. - New section on abbreviations to avoid, including Joint Commission abbreviations that are not to be used. - Incorporates updates suggested by the Institute for Safe Medication Practices (ISMP).

Download or read book The Columbia Guide to Basic Elements of Eye Care written by Daniel S. Casper and published by Springer. This book was released on 2019-07-01 with total page 519 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique resource is a practical, easy-to-use guide for the non-ophthalmologist healthcare provider as they encounter patients with eye complaints and other concerning ophthalmic conditions. The Columbia Guide to Basic Elements of Eye Care is specifically designed with the non-ophthalmologist in mind, and provides a foundation of basic eye anatomy and physiology, functional analysis, pathology, and concepts in eye care. Each chapter delivers an accessible summary of various ophthalmic diseases and conditions, all of which are frequently encountered in everyday practice. These chapters provide in-depth discussions on a wide range of topics, from testing and examination procedures to management protocols, referral guidelines and expected frequency of follow-up for each disorder. Complete with hundreds of high-quality, descriptive illustrations and clinical photographs, The Columbia Guide to Basic Elements of Eye Care presents clear, understandable explanations of basic eye anatomy, physiology, disease and treatment for non-ophthalmic practitioners and students. In doing so, this guide provides a framework for determining the normal versus the abnormal, helping the reader recognize which patients require referral, and identify which conditions are developing, require urgent treatment, or can be routinely followed. Non-ophthalmologist healthcare providers and students alike will find this book, written by leaders in the field, a practical resource to consult as they encounter patients with treatable but potentially sight-threatening conditions.

Download or read book Internal Combustion Engines written by Institution of Mechanical Engineers and published by Woodhead Publishing. This book was released on 2014-10-10 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the papers from the Internal Combustion Engines: Performance, fuel economy and emissions held in London, UK. This popular international conference from the Institution of Mechanical Engineers provides a forum for IC engine experts looking closely at developments for personal transport applications, though many of the drivers of change apply to light and heavy duty, on and off highway, transport and other sectors. These are exciting times to be working in the IC engine field. With the move towards downsizing, advances in FIE and alternative fuels, new engine architectures and the introduction of Euro 6 in 2014, there are plenty of challenges. The aim remains to reduce both CO2 emissions and the dependence on oil-derivate fossil fuels whilst meeting the future, more stringent constraints on gaseous and particulate material emissions as set by EU, North American and Japanese regulations. How will technology developments enhance performance and shape the next generation of designs? The book introduces compression and internal combustion engines' applications, followed by chapters on the challenges faced by alternative fuels and fuel delivery. The remaining chapters explore current improvements in combustion, pollution prevention strategies and data comparisons. - Presents the latest requirements and challenges for personal transport applications - Gives an insight into the technical advances and research going on in the IC Engines field - Provides the latest developments in compression and spark ignition engines for light and heavy-duty applications, automotive and other markets

Download or read book Pollutants from Energy Sources written by Rashmi Avinash Agarwal and published by Springer. This book was released on 2018-11-01 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses different aspects of energy consumption and environmental pollution, describing in detail the various pollutants resulting from the utilization of natural resources and their control techniques. It discusses diagnostic techniques in a simple and easy-to-understand manner. It will be useful for engineers, agriculturists, environmentalists, ecologists and policy makers involved in area of pollutants from energy, environmental safety, and health sectors.