Download or read book Evaluation of Low Temperature Cracking in Asphalt Pavement Mixes written by Khaled Ksaibati and published by . This book was released on 1998 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report examines the feasibility of using the thermal stress restrained specimen test to evaluate low temperature cracking in asphalt pavement mixes. Data were collected from laboratory and field evaluations. Various mixing, aging, and compaction methods were used to prepare test samples with materials obtained from two Wyoming Department of Transportation (WYDOT) highway projects. Field data were obtained from two recently built test sections and compared with laboratory test results. Pavement condition surveys quantified low temperature cracking of both test sections after one winter. Temperature data for the project sites also were collected. Pavement condition and temperature data were compared to results from the thermal stress restrained specimen test. The thermal stress restrained specimen test was effective in testing asphalt pavement mixes. However, test results indicated that lab prepared samples did not closely simulate field samples. Also, comparisons of lab results with field conditions were performed. However, it is recommended that a more comprehensive analysis be performed after test sections have been in service for a few years.
Download or read book Evaluation of Low Temperature Cracking in Asphalt Pavement Mixes written by and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Assessment of Low Temperature Cracking in Asphalt Pavement Mixes and Rheological Performance of Asphalt Binders written by and published by . This book was released on 2015 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: Government spends a lot of money on the reconstruction and rehabilitation of road pavements in any given year due to various distresses and eventual failure. Low temperature (thermal) cracking, one of the main types of pavement distress, contributes partly to this economic loss, and comes about as a result of accumulated tensile strains exceeding the threshold tensile strain capacity of the pavement. This pavement distress leads to a drastic reduction of the pavement's service life and performance. In this study, the severity of low temperature (thermal) cracking on road pavements selected across the Province of Ontario and its predicted time to failure was assessed using the AASTHO Mechanistic-Empirical Pavement Design Guide (MEPDG) and AASHTOWARE (TM) software, with inputs such as creep compliance and tensile strength from laboratory test. Highway 400, K1, K2, Y1, Sasobit, Rediset LQ, and Rediset WMX were predicted to have a pavement in-service life above 15 years. Additionally, the rheological performance of the recovered asphalt binders was assessed using Superpave (TM) tests such as the dynamic shear rheometer (DSR) and bending beam rheometer (BBR). Further tests using modified standard protocols such as the extended bending beam rheometer (eBBR) (LS-308) test method and double-edge notched tension (DENT) test (LS-299) were employed to evaluate the failure properties associated with in service performance. The various rheological tests showed K1 to be the least susceptible to low temperature cracking compared to the remaining samples whiles Highway 24 will be highly susceptible to low temperature cracking. X-ray fluorescence (XRF) analysis was performed on the recovered asphalt binders to determine the presence of metals such as zinc (Zn) and molybdenum (Mo) believed to originate from waste engine oil, which is often added to asphalt binders. Finally, the severity of oxidative aging (hardening) of the recovered asphalt binders was also evaluated using the Fourier transform infrared (FTIR) spectroscopy to determine the abundance of functional groups such as the carbonyl (CO) and sulfoxide (SO). Functional groups such as styrene and butadiene were also evaluated to determine the polymer modifier content in recovered asphalt binders.
Download or read book Low temperature Cracking written by D. H. Jung and published by National Research Council. This book was released on 1994 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the thermal stress restrained specimen test (TSRST), which was selected to evaluate the low-temperature cracking resistance of asphalt concrete mixtures. The TSRST system includes a load frame, step-motor-driven load ram, data acquisition hardware and software, temperature controller, and specimen alignment stand. An experiment design that considered a range of mixture and test condition variables was developed to evaluate the suitability of TSRST for characterizing low-temperature cracking resistance of asphalt concrete mixtures. Four asphalts and two aggregates were selected for the experiment. The mixture variables included asphalt type, aggregate type, and air voids content; the test condition variables included specimen size, stress relaxation, aging, and cooling rate.
Download or read book Evaluation of Indirect Tensile Test IDT Procedures for Low temperature Performance of Hot Mix Asphalt written by Donald W. Christensen and published by Transportation Research Board. This book was released on 2004 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction and Research Approach -- Findings -- Interpretation, Appraisal, and Applications -- Conclusions and Recommendations -- References -- Appendixes.
Download or read book Low Temperature Cracking written by and published by . This book was released on 1987 with total page 211 pages. Available in PDF, EPUB and Kindle. Book excerpt: Papers presented at this session include: temperature distributions in asphalt pavements (himeno, k, watanabe, t and maruyama, t); transient effects in low temperature induced failure and fracture initiation in a pavement structure (selvadurai, aps, phang, wa and au, mc); cold climate performance of canadian airport pavements (haas, r, lee, h and meyer, f); applications of a method for evaluation of low temperature tensile properties of asphalt concrete (anderson, ko and leung, sc); evaluation of bearing capacity of asphalt pavement with low-temperature transverse cracking (kasahara, a and yoshida, h); laboratory investigations of low temperature cracking susceptibility of asphalt concrete (janoo, vc and chamberlain, ej); results of laboratory tests on amir compacted asphalt slabs (abd el halim, ao, mshana, g and sithole, v). for the covering abstract of the conference see irrd 807037.
Download or read book 7th RILEM International Conference on Cracking in Pavements written by A. Scarpas and published by Springer Science & Business Media. This book was released on 2012-08-30 with total page 1340 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the recent past, new materials, laboratory and in-situ testing methods and construction techniques have been introduced. In addition, modern computational techniques such as the finite element method enable the utilization of sophisticated constitutive models for realistic model-based predictions of the response of pavements. The 7th RILEM International Conference on Cracking of Pavements provided an international forum for the exchange of ideas, information and knowledge amongst experts involved in computational analysis, material production, experimental characterization, design and construction of pavements. All submitted contributions were subjected to an exhaustive refereed peer review procedure by the Scientific Committee, the Editors and a large group of international experts in the topic. On the basis of their recommendations, 129 contributions which best suited the goals and the objectives of the Conference were chosen for presentation and inclusion in the Proceedings. The strong message that emanates from the accepted contributions is that, by accounting for the idiosyncrasies of the response of pavement engineering materials, modern sophisticated constitutive models in combination with new experimental material characterization and construction techniques provide a powerful arsenal for understanding and designing against the mechanisms and the processes causing cracking and pavement response deterioration. As such they enable the adoption of truly "mechanistic" design methodologies. The papers represent the following topics: Laboratory evaluation of asphalt concrete cracking potential; Pavement cracking detection; Field investigation of pavement cracking; Pavement cracking modeling response, crack analysis and damage prediction; Performance of concrete pavements and white toppings; Fatigue cracking and damage characterization of asphalt concrete; Evaluation of the effectiveness of asphalt concrete modification; Crack growth parameters and mechanisms; Evaluation, quantification and modeling of asphalt healing properties; Reinforcement and interlayer systems for crack mitigation; Thermal and low temperature cracking of pavements; and Cracking propensity of WMA and recycled asphalts.
Download or read book An Acoustic Emission based Test to Evaluate Low Temperature Behavior of Asphalt Materials written by and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Simple Test Procedure for Evaluating Low Temperature Crack Resistance of Asphalt Concrete written by Sang Soo Kim and published by . This book was released on 2009 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: The current means of evaluating the low temperature cracking resistance of HMA relies on extensive test methods that require assumptions about material behaviors and the use of complicated loading equipment. The purpose of this study was to develop and validate a simple test method to directly measure the cracking resistance of hot mix asphalt under field-like conditions. A ring shape asphalt concrete cracking device (ACCD) was developed. ACCD utilizes the low thermal expansion coefficient of Invar steel to induce tensile stresses in a HMA sample as temperature is lowered. The results of the tests of the notched ring shaped specimens compacted around an ACCD Invar ring showed good repeatability with less than 1.0°C (1.8°F) standard deviation in cracking temperature. A laboratory validation indicated that ACCD results of five mixes correlate well with thermal stress restrained specimen test (TSRST) results with the coefficient of determination , r2 = 0.86. To prepare a sample and complete TSRST measurement, it takes minimum 2-3 days. For ACCD, two samples can be easily prepared and tested in a single day with a small test set-up. The capacity of ACCD can be increased easily with minimal cost to accommodate a larger number of samples. Among factors affecting the low temperature performance of HMA, the coefficient of thermal expansion (CTE) of aggregate has been overlooked for years. A composite model of HMA is proposed to describe the low temperature cracking phenomenon. Due to the orthotropic and composite nature of asphalt pavement contraction during cooling, the effects of aggregate CTE is amplified up to 18 times for a typical HMA. Of 14 Ohio aggregates studied, the maximum and the minimum CTEs are 11.4 and 4.0 x 10-6/°C, respectively. During cooling, the contraction of Ohio aggregate with high CTE can double the thermal strain of asphalt binders in the asphalt mix and may cause asphalt pavement thermal cracking at warmer temperature.
Download or read book Investigation of Low Temperature Thermal Cracking in Hot Mix Asphalt written by Timothy Aschenbrener and published by . This book was released on 1995 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: A study was performed to determine the influence of material properties on the thermal cracking performance of hot mix asphalt (HMA), and to determine the ability to predict thermal cracking from pavements of known field performance. The testing device used to measure the HMA properties was the thermal-stress, restrained-specimen test (TSRST), and the device used to measure the binder properties was the bending beam rheometer (BBR). The laboratory study was conducted to determine the variability of test results as an influence of 1) asphalt cement stiffness, 2) asphalt cement quantity, 3) mixes with various aggregate qualities, 4) aging, and 5) the presence of hydrated lime. The influence of the asphalt cement stiffness was the single largest factor that controlled the test results.
Download or read book Investigation of Low Temperature Cracking in Asphalt Pavements written by Mihai O. Marasteanu and published by . This book was released on 2012 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: The work detailed in this report represents a continuation of the research performed in phase one of this national pooled fund study. A number of significant contributions were made in phase two of this comprehensive research effort. Two fracture testing methods are proposed and specifications are developed for selecting mixtures based on fracture energy criteria. A draft SCB specification, that received approval by the ETG and has been taken to AASHTO committee of materials, is included in the report. In addition, alternative methods are proposed to obtain mixture creep compliance needed to calculate thermal stresses. Dilatometric measurements performed on asphalt mixtures are used to more accurately predict thermal stresses, and physical hardening effects are evaluated and an improved model is proposed to take these effects into account. In addition, two methods for obtaining asphalt binder fracture properties are summarized and discussed. A new thermal cracking model, called "ILLI-TC," is developed and validated. This model represents a significant step forward in accurately quantifying the cracking mechanism in pavements, compared to the existing TCMODEL. A comprehensive evaluation of the cyclic behavior of asphalt mixtures is presented, that may hold the key to developing cracking resistant mixtures under multiple cycles of temperature.
Download or read book Selection and Performance Evaluation of a Test Method to Assess Thermal Cracking Resistance of Asphalt aggregate Mixtures written by Duhwoe Jung and published by . This book was released on 1993 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal distress in asphalt concrete pavements is a widespread problem around the world. Thermal cracking can be divided into two modes of distress: low temperature cracking and thermal fatigue cracking. Low temperature cracking results from extremely cold temperatures; thermal fatigue cracking results from daily temperature cycles. Low temperature cracking is attributed to tensile stresses induced in the asphalt concrete pavement as the temperature drops to an extremely low temperature. If the pavement is cooled, tensile stresses develop as a result of the pavement's tendency to contract. The friction between the pavement and the base layer resists the contraction. If the tensile stress equals the strength of the mixture at that temperature, a micro-crack develops at the surface of the pavement. Under repeated temperature cycles, the crack penetrates the full depth and across the asphalt concrete layer. The thermal stress restrained specimen test (TSRST) was identified as an accelerated laboratory test to evaluate the thermal cracking resistance of asphalt concrete mixtures. The TSRST system developed at OSU includes a load system, data control/acquisition system and software, temperature control system, and specimen alignment stand. The overall system is controlled by a personal computer. A TSRST is conducted by cooling an asphalt concrete specimen at a specified rate while monitoring the specimen at constant length. A typical thermally-induced stress curve is divided into two parts: relaxation and non-relaxation. The temperature at which the curve is divided into two parts is termed the transition temperature. The temperature at fracture is termed the fracture temperature and the maximum stress is the fracture strength. An extensive number of TSRSTs over a wide range of conditions were performed to investigate the thermal cracking resistance of asphalt concrete mixtures. The TSRST results provided a very strong indication of low temperature cracking resistance for all mixtures considered. A ranking of mixtures for low temperature cracking resistance based on the TSRST fracture temperature was in excellent agreement with a ranking based on the physical properties of the asphalt cements. It is highly recommended that the TSRST be used in mix evaluation to identify low temperature cracking resistance of asphalt concrete mixtures. The TSRST showed very promising results regarding the effect of all variables which are currently considered to affect the low temperature cracking of mixtures. The variables considered to have significant affect on the low temperature cracking resistance of mixtures in this study include asphalt type, aggregate type, degree of aging, cooling rate, and stress relaxation.
Download or read book Low temperature Cracking written by Hannele K. Kanerva and published by National Research Council. This book was released on 1994 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of the field validation program was to evaluate the thermal stress restrained specimen test (TSRST) as the accelerated performance test to predict low-temperature cracking of asphalt concrete mixtures. Construction histories, cracking observations, and temperature data were collected for five test roads. In addition, a validation program was conducted at the United States Army Cold Regions Research and Engineering Laboratory. The laboratory test program consisted of performing the TSRST on specimens fabricated in the laboratory with original materials from the test roads and asphalt concrete pavement specimens cut from the actual test sections. In addition, the field pavements were monitored for crack history and, where possible, crack initiation. TSRST fracture temperature correlated with field cracking temperature and crack frequency. TSRST results can be used to predict field low-temperature cracking of asphalt-aggregate mixtures. Preliminary models to predict cracking frequency and temperature for the test roads were developed.
Download or read book Improved Mix Design Evaluation and Materials Management Practices for Hot Mix Asphalt with High Reclaimed Asphalt Pavement Content written by Randy Clark West and published by Transportation Research Board. This book was released on 2013 with total page 162 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Report 752: Improved Mix Design, Evaluation, and Materials Management Practices for Hot Mix Asphalt with High Reclaimed Asphalt Pavement Content describes proposed revisions to the American Association of State Highway and Transportation Officials (AASHTO) R 35, Superpave Volumetric Design for Hot Mix Asphalt, and AASHTO M 323, Superpave Volumetric Mix Design, to accommodate the design of asphalt mixtures with high reclaimed asphalt pavement contents.
Download or read book Low temperature Cracking written by D. H. Jung and published by Strategic Highway Research Program (Shrp). This book was released on 1994 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: A thermal stress restrained specimen test (TSRST) was developed to determine the thermal, or the low-temperature cracking resistance of asphalt concrete mixes. The test system is capable of cooling an asphalt concrete specimen at a constant rate, while restraining the specimen from contraction and periodically measuring elapsed time, specimen surface temperature, and tensile load. TSRST's were performed on both short- and long-term aged specimens. Statistical analyses were performed on the test results. Rankings of asphalt concrete mixtures based on fracture temperature were compared to rankings based on fundamental properties of the asphalt cement.
Download or read book Pavement Cracking written by Imad L. Al-Qadi and published by CRC Press. This book was released on 2008-07-30 with total page 932 pages. Available in PDF, EPUB and Kindle. Book excerpt: Internationally, much attention is given to causes, prevention, and rehabilitation of cracking in concrete, flexible, and composite pavements. The Sixth RILEMInternational Conference on Cracking in Pavements (Chicago, June 16-18, 2008) provided a forum for discussion of recent developments and research results.This book is a collection of papers fr
Download or read book Superpave Mix Design written by Asphalt Institute and published by . This book was released on 2001-01-01 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: