Download or read book Eurocode 8 Design of structures for earthquake resistance Part 1 General rules seismic actions and rules for buildings written by and published by . This book was released on 2005 with total page 229 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Seismic Design of Buildings to Eurocode 8 written by Ahmed Elghazouli and published by CRC Press. This book was released on 2016-12-19 with total page 383 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the seismic design of building structures and their foundations to Eurocode 8. It covers the principles of seismic design in a clear but brief manner and then links these concepts to the provisions of Eurocode 8. It addresses the fundamental concepts related to seismic hazard, ground motion models, basic dynamics, seismic analysis, siting considerations, structural layout, and design philosophies, then leads to the specifics of Eurocode 8. Code procedures are applied with the aid of walk-through design examples which, where possible, deal with a common case study in most chapters. As well as an update throughout, this second edition incorporates three new and topical chapters dedicated to specific seismic design aspects of timber buildings and masonry structures, as well as base-isolation and supplemental damping. There is renewed interest in the use of sustainable timber buildings, and masonry structures still represent a popular choice in many areas. Moreover, seismic isolation and supplemental damping can offer low-damage solutions which are being increasingly considered in practice. The book stems primarily from practical short courses on seismic design which have been run over a number of years and through the development Eurocode 8. The contributors to this book are either specialist academics with significant consulting experience in seismic design, or leading practitioners who are actively engaged in large projects in seismic areas. This experience has provided significant insight into important areas in which guidance is required.
Download or read book Design of Steel Structures for Buildings in Seismic Areas written by ECCS - European Convention for Constructional Steelwork and published by John Wiley & Sons. This book was released on 2018-01-03 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume elucidates the design criteria and principles for steel structures under seismic loads according to Eurocode 8-1. Worked Examples illustrate the application of the design rules. Two case studies serve as best-practice samples.
Download or read book Critical comparison of major seismic codes for buildings written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2013-01-01 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 69 illustrates and compares major buildings seismic codes applied in the different Continents, namely U.S., Japan, New Zealand, Europe, Canada, Chile and Mexico. Bulletin 69 was prepared by Task Group 7.6 of fib Commission 7, under the leadership of the late Professor Robert (Bob) Park which, in tandem with Professor Paulay, had developed in the seventies new fundamental design concepts, most notably capacity design approach and structural design for ductility, that had made the NZ seismic Code the most advanced one of the time. This new approach has highly influenced the development of Eurocode 8, to which Bob Park has significantly contributed. Bob Park was also well informed of the situation in Japan, USA, Canada and South America. Such a wide view is reflected in Bulletin 69 showing similarities and differences among the major seismic codes, accompanied as far as possible by comments, hopefully useful for fostering international harmonization. A comprehensive summary of the major codes is provided in the first chapter of the bulletin. All codes are separately presented according to a common framework: an introduction section, which describes the history, the philosophy, the process development, the performance-based criteria, the strength of materials and the incorporation of strength reduction factors of each code; a second section devoted to the demand side, which specify the seismic design actions and associated criteria of each code for areas of different seismicity and for structures with different ductility properties/requirements; a third section devoted to the capacity side, which describes the capacities of members and joints and associated criteria of each code, including member strengths in flexure, shear and bars anchorage, desirable hierarchies of strength attainment, deformation capacities of mechanisms of inelastic deformation, detailing of beams, columns and structural walls, detailing of beam-column joints for shear and the detailing of diaphragms. The second chapter is devoted to the comparison of the more significant issues dealt in the considered codes. This includes: seismic design actions and associated criteria, capacity design practice, beams, columns, confinement, structural walls and joints. It is felt that fib Bulletin 69 represents a useful, unique instrument for rapidly gaining an overview of the distinguishing features of the major world codes, under both their conceptual framework and application rules.
Download or read book Design of Steel Structures to Eurocodes written by Ioannis Vayas and published by Springer. This book was released on 2018-11-23 with total page 595 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook describes the rules for the design of steel and composite building structures according to Eurocodes, covering the structure as a whole, as well as the design of individual structural components and connections. It addresses the following topics: the basis of design in the Eurocodes framework; the loads applied to building structures; the load combinations for the various limit states of design and the main steel properties and steel fabrication methods; the models and methods of structural analysis in combination with the structural imperfections and the cross-section classification according to compactness; the cross-section resistances when subjected to axial and shear forces, bending or torsional moments and to combinations of the above; component design and more specifically the design of components sensitive to instability phenomena, such as flexural, torsional and lateral-torsional buckling (a section is devoted to composite beams); the design of connections and joints executed by bolting or welding, including beam to column connections in frame structures; and alternative configurations to be considered during the conceptual design phase for various types of single or multi-storey buildings, and the design of crane supporting beams. In addition, the fabrication and erection procedures, as well as the related quality requirements and the quality control methods are extensively discussed (including the procedures for bolting, welding and surface protection). The book is supplemented by more than fifty numerical examples that explain in detail the appropriate procedures to deal with each particular problem in the design of steel structures in accordance with Eurocodes. The book is an ideal learning resource for students of structural engineering, as well as a valuable reference for practicing engineers who perform designs on basis of Eurocodes.
Download or read book EARTHQUAKE RESISTANT DESIGN OF STRUCTURES written by PANKAJ AGRAWAL and published by PHI Learning Pvt. Ltd.. This book was released on 2006-01-01 with total page 666 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive and well-organized book presents the concepts and principles of earthquake resistant design of structures in an easy-to-read style. The use of these principles helps in the implementation of seismic design practice. The book adopts a step-by-step approach, starting from the fundamentals of structural dynamics to application of seismic codes in analysis and design of structures. The text also focusses on seismic evaluation and retrofitting of reinforced concrete and masonry buildings. The text has been enriched with a large number of diagrams and solved problems to reinforce the understanding of the concepts. Intended mainly as a text for undergraduate and postgraduate students of civil engineering, this text would also be of considerable benefit to practising engineers, architects, field engineers and teachers in the field of earthquake resistant design of structures.
Download or read book Eurocode 8 Design of Structures for Earthquake Resistance written by and published by . This book was released on 2005 with total page 229 pages. Available in PDF, EPUB and Kindle. Book excerpt: Earthquake-resistant design, Structures, Structural design, Seismology, Structural systems, Construction systems, Hazard prevention in buildings, Safety measures, Seismic intensity, Plastic analysis, Design calculations, Foundations, Classification systems, Subsoil, Earthquake zones, Earthquakes, Mathematical calculations
Download or read book 20th International Probabilistic Workshop written by José C. Matos and published by Springer Nature. This book was released on with total page 536 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Progresses in European Earthquake Engineering and Seismology written by Radu Vacareanu and published by Springer Nature. This book was released on 2022-08-24 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book encompasses the most challenging topics in earthquake engineering and seismology aiming at seismic risk reduction and reveals the outstanding progresses made in Europe in the past four years. Earthquakes pose a significant threat to countries around the world. But, equipped with the right knowledge and tools, engineers and seismologists can support policy and decision makers and building officials in creating a safer future for all of us. In this paradigm, the Third European Conference on Earthquake Engineering and Seismology (3ECEES) is organized in Bucharest (Romania) in September 2022 by the Romanian Association for Earthquake Engineering, Technical University of Civil Engineering of Bucharest and National Institute for Earth Physics. This outstanding scientific event is the third in a series started in 2006 in Geneva, Switzerland and continued in 2014 in Istanbul, Turkey. The papers included in this book are written by the most prominent contemporary European scholars in the two-folded fields of 3ECEES. The Distinguished Nicholas Ambraseys, along with 28 invited lectures providing the best knowledge in the fields of earthquake engineering and seismology, are shared with the general readership of this book. The book is organized in three parts, as follows: (1) Seismicity, engineering seismology and seismic hazard, (2) Seismic risk assessment and mitigation, and (3) Structural earthquake engineering. The 29 contributed papers for this book are shared among these three parts almost equally. Chapter “The Challenge of the Integrated Seismic Strengthening and Environmental Upgrading of Existing Buildings” is available open access under a Creative Commons Attribution 4.0 International License via link.springer.com.
Download or read book Precast Concrete Structures written by Alfred Steinle and published by John Wiley & Sons. This book was released on 2019-01-28 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Building with precast concrete elements is one of the most innovative forms of construction. This book serves as an introduction to this topic, including examples, and thus supplies all the information necessary for conceptual and detailed design.
Download or read book Proceedings of AICCE 19 written by Fadzli Mohamed Nazri and published by Springer Nature. This book was released on 2019-11-28 with total page 1635 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers the latest research, innovations, and applications in the field of civil engineering, as presented by leading national and international academics, researchers, engineers, and postgraduate students at the AWAM International Conference on Civil Engineering 2019 (AICCE’19), held in Penang, Malaysia on August 21-22, 2019. The book covers highly diverse topics in the main fields of civil engineering, including structural and earthquake engineering, environmental engineering, geotechnical engineering, highway and transportation engineering, water resources engineering, and geomatic and construction management. In line with the conference theme, “Transforming the Nation for a Sustainable Tomorrow”, which relates to the United Nations’ 17 Global Goals for Sustainable Development, it highlights important elements in the planning and development stages to establish design standards beneficial to the environment and its surroundings. The contributions introduce numerous exciting ideas that spur novel research directions and foster multidisciplinary collaborations between various specialists in the field of civil engineering.
Download or read book Sustainable Building with Earth written by Horst Schroeder and published by Springer. This book was released on 2015-09-28 with total page 575 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an insightful overview of the current state of earth building. The author approaches the subject from the perspective of the building material’s life cycle, featuring in-depth explanations of the cycle's individual steps: extraction and classification of construction soil; production of earth building materials and earthen structures; planning, construction and renovation of earth buildings; and demolition and recycling of earthen structures. This unique resource provides examples of sophisticated earth building projects and illustrates the diverse applications of earth as a building material. Compared to conventional mineral building materials, earth possesses particularly positive ecological qualities such as its energy balance and recyclability. Architects, engineers, students, manufacturers and distributors of building materials, building contractors, building biologists, public authorities and preservationists will benefit from this book’s ample coverage of restoring, optimizing and building with this material of the past, present and future.
Download or read book Analysis Procedure for Earthquake Resistant Structures written by Farzad Hejazi and published by Springer. This book was released on 2018-05-15 with total page 536 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents an analysis procedure for structures that are exposed to the lateral loads such as earthquake and wind. It includes the process for calculating and distributing the effective load into structural elements, as well as for calculating the displacements for different types of structures, e.g. reinforced concrete and steel framed structures. The book provides civil engineers with clear guidelines on how to perform seismic analysis for various building systems, and how to distribute the lateral load to the structural components. This book consists of 4 chapters: The first chapter offers an introduction, while Chapter 2 discusses moment resistance frame. The final two chapters explore shear wall frames and brace frames respectively. Each chapter follows the same structure, explaining step by step all the necessary algorithms, equations and procedures for calculating 1) loads, 2) the centre of mass, 3) stiffness of structures, 4) centre of stiffness, 5) lateral loading, 6) the distribution of lateral loads, and 7) the lateral displacement. Demonstrating the implementation of real building analysis, the book provides architectural drawings and structural plans at the beginning of each chapter.
Download or read book Historical Earthquake Resistant Timber Framing in the Mediterranean Area written by Helena Cruz and published by Springer. This book was released on 2016-08-29 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a selection of the best papers from the HEaRT 2015 conference, held in Lisbon, Portugal, which provided a valuable forum for engineers and architects, researchers and educators to exchange views and findings concerning the technological history, construction features and seismic behavior of historical timber-framed walls in the Mediterranean countries. The topics covered are wide ranging and include historical aspects and examples of the use of timber-framed construction systems in response to earthquakes, such as the gaiola system in Portugal and the Bourbon system in southern Italy; interpretation of the response of timber-framed walls to seismic actions based on calculations and experimental tests; assessment of the effectiveness of repair and strengthening techniques, e.g., using aramid fiber wires or sheets; and modelling analyses. In addition, on the basis of case studies, a methodology is presented that is applicable to diagnosis, strengthening and improvement of seismic performance and is compatible with modern theoretical principles and conservation criteria. It is hoped that, by contributing to the knowledge of this construction technique, the book will help to promote conservation of this important component of Europe’s architectural heritage.
Download or read book Numerical Methods and Applications written by Ivan Dimov and published by Springer. This book was released on 2015-02-03 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the thoroughly refereed post-conference proceedings of the 8th International Conference on Numerical Methods and Applications, NMA 2014, held in Borovets, Bulgaria, in August 2014. The 34 revised full papers presented were carefully reviewed and selected from 56 submissions for inclusion in this book. The papers are organized in the following topical sections: Monte Carlo and quasi-Monte Carlo methods; metaheuristics for optimization problems; advanced numerical methods for scientific computing; advanced numerical techniques for PDEs and applications; solving large engineering and scientific problems with advanced mathematical models; numerical simulations and back analysis in civil and mechanical engineering.
Download or read book Trends in Civil Engineering and Challenges for Sustainability written by M. C. Narasimhan and published by Springer Nature. This book was released on 2020-09-28 with total page 869 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises selected papers from the International Conference on Civil Engineering Trends and Challenges for Sustainability (CTCS) 2019. The book presents latest research in several areas of civil engineering such as construction and structural engineering, geotechnical engineering, environmental engineering and sustainability, and geographical information systems. With a special emphasis on sustainable development, the book covers case studies and addresses key challenges in sustainability. The scope of the contents makes the book useful for students, researchers, and professionals interested in sustainable practices in civil engineering.
Download or read book Nondestructive Techniques for the Assessment and Preservation of Historic Structures written by Luisa Maria da Silva Gonçalves and published by CRC Press. This book was released on 2017-10-02 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: New technologies play an increasingly important role in the analysis, monitoring, restoration, and preservation of historic structures. These technological systems continue to get more advanced and complex, for example: 3D digital construction and documentation programming, 3D imaging data (including laser scanning and photogrammetry), multispectral and thermographic imaging, geophysical data, etc. This book will present the latest nondestructive technologies used in the characterization, preservation, and structural health monitoring of historic buildings. It will include numerous case studies, as well as theoretical explanations about each of the methods and technologies used in each.
