Download or read book Effect of Temperature and Strain Rate on the Mechanical Behavior of AL SIC Particulates Metal Matrix Composites written by Mohamed Mahmoud Zaki Emara and published by . This book was released on 1998 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Heat Treatment and Interface Effects on the Mechanical Behavior of SiC Particle Reinforced Aluminium Matrix Composites written by D. P. Myriounis and published by . This book was released on 2008 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt: The interface plays a vital role in composites. Strengthening behavior of SiC-particle reinforced aluminium matrix composites relies on load transfer behavior across the interface, whereas toughness is influenced by crack deflection at the boundary between matrix and reinforcement and ductility is affected by relaxation of peak stresses near the interface. In general, metal matrix composites often behave asymmetrically in tension and in compression and have higher ultimate tensile strength, yet lower proportional limits, than monolithic alloys. Such behavior of composites lies with the factors governing matrix plasticity, which can be divided into two areas: those affecting the stress rate of the matrix, and those which alter the flow properties of the matrix through changes in microstructure induced by inclusion of the reinforcement. This work focuses on the characterization of the mechanical response of the interface to stresses arising from an applied load in SiC-particle reinforced aluminium matrix composites. The composites have been studied in the as-received (T1) and in the T6 and modified T6 (HT1) conditions. In the nonequilibrium heat treatment processing of the composites, nonequilibrium segregation arises due to imbalances in point defect concentrations set up around interfaces. Mechanical properties, including microhardness and stress-strain behavior, of aluminum matrix composites containing various percentages of SiC particulate reinforcement have been investigated. The elastic modulus, the yield/tensile strengths, and ductility of the composites were controlled primarily by the volume percentage of SiC reinforcement, the temper condition, and the precipitation hardening.
Download or read book Metal Matrix Composites written by International Conference on Composite Materials and published by Woodhead Publishing. This book was released on 1993 with total page 940 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal and Mechanical Behavior of Metal Matrix and Ceramic Matrix Composites written by John M. Kennedy and published by ASTM International. This book was released on 1990 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: Of interest to researchers and practitioners in materials science, especially in the aerospace industry, 16 papers from a symposium in Atlanta, Georgia, November 1988 discuss the analysis, modeling, and behavior of both continuous and discontinuous ceramic and metal matrix composites, and methods of
Download or read book Aluminum and Aluminum Alloys written by Joseph R. Davis and published by ASM International. This book was released on 1993-01-01 with total page 802 pages. Available in PDF, EPUB and Kindle. Book excerpt: This one-stop reference is a tremendous value and time saver for engineers, designers and researchers. Emerging technologies, including aluminum metal-matrix composites, are combined with all the essential aluminum information from the ASM Handbook series (with updated statistical information).
Download or read book Processing Properties and Applications of Cast Metal Matrix Composites written by P. K. Rohatgi and published by Minerals, Metals, & Materials Society. This book was released on 1996 with total page 378 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book the current status of metal matrix covers composites which are produced via solidification technology. It examines processes involved in the synthesizing of composites, structure/property relationships, and established and emerging industrial applications, particularly in the automotive industry.
Download or read book Proceedings written by Murray L. Scott and published by Woodhead Publishing. This book was released on 1997 with total page 836 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Affordable Metal Matrix Composites for High Performance Applications II written by Awadh B. Pandey and published by John Wiley & Sons. This book was released on 2013-09-23 with total page 405 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will include papers on recent research carried out in the field of metal-matrix composites (MMCs). Processing, microstructure, and mechanical properties of MMCs and unreinforced matrix alloys will be covered with a focus on aluminum, titanium, nickel, and copper MMCs. Those involved in the research of MMCs and unreinforced alloys, particularly in aerospace, space, and automotive materials research, will find this volume indispensible. From Materials Science & Technology 2003 to be held in Chicago, Illinois, November 9-12, 2003.
Download or read book Mechanical Behavior of Metal matrix Composites written by John E. Hack and published by . This book was released on 1983 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Temperature Mechanical Behaviour of Ceramic Composites written by Shanti Nair and published by Butterworth-Heinemann. This book was released on 1995-05-15 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction; Interfaces; Residual stresses; Fibre properties; Matrix cracking in unidirectional materials; Matrix cracking in 2-D materials; Stress redistribution; Fatigue, creep, challenges and opportunities.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 836 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Forum on Structural Ceramics Joining Volume 10 Issue 11 12 written by John B. Wachtman and published by John Wiley & Sons. This book was released on 2009-09-28 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is part of the Ceramic Engineering and Science Proceeding (CESP) series. This series contains a collection of papers dealing with issues in both traditional ceramics (i.e., glass, whitewares, refractories, and porcelain enamel) and advanced ceramics. Topics covered in the area of advanced ceramic include bioceramics, nanomaterials, composites, solid oxide fuel cells, mechanical properties and structural design, advanced ceramic coatings, ceramic armor, porous ceramics, and more.
Download or read book Physics Briefs written by and published by . This book was released on 1994 with total page 1118 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Introduction to Metal Matrix Composites written by T. W. Clyne and published by Cambridge University Press. This book was released on 1993 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal matrix composites constitute a new class of materials, now starting to make a major industrial impact in fields as diverse as aerospace, automotives and electronics. This book gives a comprehensive, integrated coverage of these materials, including the background to analytical-, experimental-, production and application-oriented aspects. Clear pictorial descriptions are given of the basic principles governing various properties and characteristics; these encompass mechanical, thermal, electrical, environmental and wear behaviour. Coverage also extends to material processing and component fabrication aspects and to a survey of commercial usage. This book is aimed primarily at scientists, engineers, production managers and all those involved in research on new materials in general, and metal matrix composites in particular, but may also be suitable for use as a text in beginning graduate and advanced undergraduate courses.
Download or read book Effect of Strain Rate on Mechanical Properties of Aluminum silicon Carbide Composites written by P. Mayer and published by . This book was released on 1991 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Comprehensive Materials Processing written by and published by Newnes. This book was released on 2014-04-07 with total page 5485 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive Materials Processing, Thirteen Volume Set provides students and professionals with a one-stop resource consolidating and enhancing the literature of the materials processing and manufacturing universe. It provides authoritative analysis of all processes, technologies, and techniques for converting industrial materials from a raw state into finished parts or products. Assisting scientists and engineers in the selection, design, and use of materials, whether in the lab or in industry, it matches the adaptive complexity of emergent materials and processing technologies. Extensive traditional article-level academic discussion of core theories and applications is supplemented by applied case studies and advanced multimedia features. Coverage encompasses the general categories of solidification, powder, deposition, and deformation processing, and includes discussion on plant and tool design, analysis and characterization of processing techniques, high-temperatures studies, and the influence of process scale on component characteristics and behavior. Authored and reviewed by world-class academic and industrial specialists in each subject field Practical tools such as integrated case studies, user-defined process schemata, and multimedia modeling and functionality Maximizes research efficiency by collating the most important and established information in one place with integrated applets linking to relevant outside sources
Download or read book Metals Abstracts Index written by and published by . This book was released on 1996 with total page 1634 pages. Available in PDF, EPUB and Kindle. Book excerpt:
