Download or read book Fundamentals of Fluid Film Lubrication written by Bernard J. Hamrock and published by CRC Press. This book was released on 2004-03-15 with total page 747 pages. Available in PDF, EPUB and Kindle. Book excerpt: Specifically focusing on fluid film, hydrodynamic, and elastohydrodynamic lubrication, this edition studies the most important principles of fluid film lubrication for the correct design of bearings, gears, and rolling operations, and for the prevention of friction and wear in engineering designs. It explains various theories, procedures, and equations for improved solutions to machining challenges. Providing more than 1120 display equations and an introductory section in each chapter, Fundamentals of Fluid Film Lubrication, Second Edition facilitates the analysis of any machine element that uses fluid film lubrication and strengthens understanding of critical design concepts.

Download or read book Elasto Hydrodynamic Lubrication written by D. Dowson and published by Elsevier. This book was released on 2014-07-18 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: Elasto-Hydrodynamic Lubrication deals with the mechanism of elasto-hydrodynamic lubrication, that is, the lubrication regime in operation over the small areas where machine components are in nominal point or line contact. The lubrication of rigid contacts is discussed, along with the effects of high pressure on the lubricant and bounding solids. The governing equations for the solution of elasto-hydrodynamic problems are presented. Comprised of 13 chapters, this volume begins with an overview of elasto-hydrodynamic lubrication and representation of contacts by cylinders, followed by a discussion on equations relevant to lubrication, including the Reynolds equation. The reader is then introduced to lubrication of rigid cylinders; the importance of film thickness in highly loaded rigid contacts; the elasticity of solids in contact; and the theory of elasto-hydrodynamic lubrication. Subsequent chapters focus on apparatus and measurements of film thickness and film shape; friction and viscosity; and lubrication of gears and roller bearings. This book will be of interest to tribologists.

Download or read book Handbook of Workability and Process Design written by George E. Dieter and published by ASM International. This book was released on 2003-01-01 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fundamentals of Engineering Tribology with Applications written by Harish Hirani and published by Cambridge University Press. This book was released on 2016-03-11 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology is related to friction, wear and lubrication of machine elements. Tribology not only deals with the design of fluid containment systems like seals and gasket but also with the lubrication of surfaces in relative motion. This book comprehensively discusses the theories and applications of hydrodynamic thrust bearing, gas (air) lubricated bearing and elasto-hydrodynamic lubrication. It elucidates the concepts related to friction, including coefficient of friction, friction instability and stick-slip motion. It clarifies the misconception that harder and cleaner surfaces produce better results in wear. Recent developments, including online condition monitoring (an integration of moisture sensor, wear debris and oil quality sensors) and multigrid technique, are discussed in detail. The book also offers design problems and their real-life applications for cams, followers, gears and bearings. MATLAB programs, frequently asked questions and multiple choice questions are interspersed throughout for easy understanding of the topics.

Download or read book COMPUTER ORIENTED NUMERICAL METHODS written by P. THANGARAJ and published by PHI Learning Pvt. Ltd.. This book was released on 2008-07-22 with total page 398 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical methods are powerful problem-solving tools. Techniques of these methods are capable of handling large systems of equations, nonlinearities and complicated geometries in engineering practice which are impossible to be solved analytically. Numerical methods can solve the real world problem using the C program given in this book. This well-written text explores the basic concepts of numerical methods and gives computational algorithms, flow charts and programs for solving nonlinear algebraic equations, linear equations, curve fitting, integration, differentiation and differential equations. The book is intended for students of B.E. and B.Tech as well as for students of B.Sc. (Mathematics and Physics). KEY FEATURES  Gives clear and precise exposition of modern numerical methods.  Provides mathematical derivation for each method to build the student’s understanding of numerical analysis.  Presents C programs for each method to help students to implement the method in a programming language.  Includes several solved examples to illustrate the concepts.  Contains exercises with answers for practice.

Download or read book TECHNOLOGY OF METAL FORMING PROCESSES written by SURENDER KUMAR and published by PHI Learning Pvt. Ltd.. This book was released on 2008-06-20 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive text presents the subject of metalworking by offering a clear account of the theory and applications of metal forming processes relevant to engineering practice. It is designed to serve as a textbook for undergraduate and postgraduate students of mechanical engineering, production engineering, industrial engineering, and metallurgical engineering. The first seven chapters are devoted to basic concepts to equip the students with the background material on mechanics, material sciences and to provide them with a sound foundation in the theory of plasticity. In addition, the importance of friction and lubrication in metal forming processes is adequately highlighted. In the next nine chapters the reader is exposed to a richly detailed discussion of specific forming processes (including the lubricated metal forming processes) and new and powerful techniques are presented (load bounding and slip line field) for solving engineering problems in metal forming. The book then moves on to forming of polymers and also covers metal powder preforms, highlighting recent developments. In the concluding portions of the book, the important factors such as force, power requirements, formability and machinability in the study of individual processes, are briefly discussed. Finally, the application of computer-aided analysis in the metalworking processes has been demonstrated, being the demand in this competitive scenario. Several chapter-end exercises are included to aid better understanding of the theory.

Download or read book Lubricants and Lubrication 2 Volume Set written by Theo Mang and published by John Wiley & Sons. This book was released on 2017-05-08 with total page 1220 pages. Available in PDF, EPUB and Kindle. Book excerpt: Praise for the previous edition: "Contains something for everyone involved in lubricant technology." —Chemistry & Industry This completely revised third edition incorporates the latest data available and reflects the knowledge of one of the largest companies active in the business. The authors take into account the interdisciplinary character of the field, considering aspects of engineering, materials science, chemistry, health and safety. The result is a volume providing chemists and engineers with a clear interdisciplinary introduction and guide to all major lubricant applications, focusing not only on the various products but also on specific application engineering criteria. A classic reference work, completely revised and updated (approximately 35% new material) focusing on sustainability and the latest developments, technologies and processes of this multi billion dollar business Provides chemists and engineers with a clear interdisciplinary introduction and guide to all major lubricant applications, looking not only at the various products but also at specific application engineering criteria All chapters are updated in terms of environmental and operational safety. New guidelines, such as REACH, recycling alternatives and biodegradable base oils are introduced Discusses the integration of micro- and nano-tribology and lubrication systems Reflects the knowledge of Fuchs Petrolub SE, one of the largest companies active in the lubrication business 2 Volumes wileyonlinelibrary.com/ref/lubricants

Download or read book Principles of Tribology written by Shizhu Wen and published by John Wiley & Sons. This book was released on 2012-02-21 with total page 477 pages. Available in PDF, EPUB and Kindle. Book excerpt: Professors Wen and Huang present current developments in tribology research along with tribology fundamentals and applications, including lubrication theory, lubrication design, friction mechanism, wear mechanism, friction control, and their applications. In addition to classical tribology, Wen and Huang cover the research areas of the modern tribology, as well as the regularities and characteristics of tribological phenomena in practice. Furthermore, the authors present the basic theory, numerical analysis methods, and experimental measuring techniques of tribology as well as their applications in engineering. Provides a systematic presentation of tribology fundamentals and their applications Discusses the current states and development trends in tribology research Applies the applications to modern day engineering Computer programs available for download from the book’s companion site Principles of Tribology is aimed at postgraduates and senior-level undergraduates studying tribology, and can be used for courses covering theory and applications. Tribology professionals and students specializing in allied areas of mechanical engineering and materials science will also find the book to be a helpful reference or introduction to the topic. Companion website for the book: www.wiley.com/go/wen/tribology

Download or read book Stal in English written by and published by . This book was released on 1969 with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metal Forming 2016 written by Danuta Szeliga and published by Trans Tech Publications Ltd. This book was released on 2016-10-17 with total page 1008 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selected, peer reviewed papers from the 16th Metal Forming International Conference, September 18-21, 2016, Kraków, Poland

Download or read book Lubricants and Lubrication written by Theo Mang and published by John Wiley & Sons. This book was released on 2007-02-27 with total page 890 pages. Available in PDF, EPUB and Kindle. Book excerpt: This completely revised second edition incorporates the latest data available and reflects the knowledge of one of the largest companies active in the business. The authors take into account the interdisciplinary character of the field, considering aspects of engineering, materials science, chemistry, health and safety. The result is a volume providing chemists and engineers with a clear interdisciplinary introduction and guide to all major lubricant applications, focusing not only on the various products but also on specific application engineering criteria.

Download or read book Fluid Film Lubrication written by Andras Z. Szeri and published by Cambridge University Press. This book was released on 2010-12-27 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fluid film bearings are machine elements that should be studied within the broader context of tribology. The three subfields of tribology - friction, lubrication, and wear - are strongly interrelated. The last decade has witnessed significant advances in the area of fluid film lubrication and its applications, and this second edition offers a look at some of these advances. This edition adds to the fundamentals of fluid film lubrication, a discourse on surface effects and the inclusion of treatment of flow with significant inertia within the section on turbulence. Basic ideas of the multigrid method are conveyed along with multilevel multi-integration in the treatment of elastohydrodynamic lubrication. New chapters have been included on ultra-thin films, both liquid and gaseous, and lubrication of articulating joints and their replacement. Some of the most recent literature is discussed.

Download or read book Springer Handbook of Mechanical Engineering written by Karl-Heinrich Grote and published by Springer Nature. This book was released on 2020-12-09 with total page 1310 pages. Available in PDF, EPUB and Kindle. Book excerpt: This resource covers all areas of interest for the practicing engineer as well as for the student at various levels and educational institutions. It features the work of authors from all over the world who have contributed their expertise and support the globally working engineer in finding a solution for today‘s mechanical engineering problems. Each subject is discussed in detail and supported by numerous figures and tables.

Download or read book Solid Lubricants and Surfaces written by E. R. Braithwaite and published by Elsevier. This book was released on 2013-10-22 with total page 297 pages. Available in PDF, EPUB and Kindle. Book excerpt: Solid Lubricants and Surfaces deals with the theory and use of solid lubricants, particularly in colloidal form. Portions of this book are devoted to graphite and molybdenum disulfides, which are widely used solid lubricants in colloidal form. An extensive literature on the laboratory examination of hundreds of solids as potential lubricants is also provided in this text. Other topics discussed include the metals and solid lubricants; techniques for examining surfaces; other solid lubricants; metal shaping; and industrial uses of solid-lubricant dispersions. This publication is beneficial to equipment designers who know the value of solid lubricants and works engineers interested in the background science underlying solid-lubricant. This text is mainly useful to senior undergraduates who plan to enter the chemical engineering industries.

Download or read book Handbook of Fabrication Processes written by Orville D. Lascoe and published by ASM International. This book was released on 1988-01-01 with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a valuable reference for the materials engineer, the manufacturing engineer, or the technician who wants a practical description of fabrication processes. Sheet metal fabrication processes are receiving greater attention and are more widely applied by the metalworking industries because of the savings in cost and material. This book compiles the proven theories and operations tested in industrial applications. Focus is on the non-chip-producing machine tools that shape metals by shearing, pressing and forming. New materials and advances in tooling are discussed, as well as the need for applied science in optimizing the operations for sheet metal fabrication processes. Examples of each of these forming processes are given, and the text also describes the mechanics of each process so that a logical decision can be made concerning the best operation for a specific result. The volume is divided into five sections each consisting of a series of chapters. The major sections cover fabricating presses, stamping and forming operations, plastics for tooling, structural shapes, and non-traditional machining. A section on definitions and terminology is also included.The book is profusely illustrated and indexed, making it easy to find references to specific forming topics. Written by an expert with 40 years of hands-on practical engineering experience, this Handbook contains the essential information you need on forming methods, machinery and the response of materials.

Download or read book Advances in Machine Tool Design and Research 1967 written by S. A. Tobias and published by Elsevier. This book was released on 2013-10-08 with total page 715 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Machine Tool Design and Research 1967, Part 2 provides information pertinent to the development of machine tool design. This book discusses the advances in pneumatic positioning device in the machine tool laboratories. Organized into 41 chapters, this book starts with an overview of the pneumatic digital and analogue elements used in designing the control loop. This text then explains the control system for the cylindrical grinding process developed by fluid logic elements and the diaphragm-type fluid logic element used in the control system. Other chapters consider the causes of inaccuracies on a finished machined workpiece produced by a numerically controlled machine tool. This book discusses as well the machine errors that are corrected by instrumentation, the details of this installation, and the characteristics of the instrumentation required. The final chapter deals with the basic characteristics of material flow during closed die forging. This book is a valuable resource for production and mechanical engineers.

Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Process and Equipment Program, a survey was conducted to collect and summarize information on deformation characteristics of metals and their effect on processing operations. This report presents information obtained from reports on Governmentsponsored work and from articles in technical publications. The report covers eight subjects: extrusion, forging, rolling, thermal mechanical variables affecting the properties of refractory metals and alloys, development of preferred orientations, anisotropy of strength and ductility, high-strain-rate deformation, and strain aging. In order to be useful to engineering students and production engineers the topics are treated in two ways. Generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily. When practical, data on the more-difficultto-form metals are used to illustrate the principles, limitations, and effects of the processes. The objective is to help the non-specialist recognize the implications of specific findings and to apply them to specific operations. (Author).