Download or read book Distilling Complex Model Results Into Simple Models for Use in Assessing Compliance with Performance Standards for Low Level Waste Disposal Facilities written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Assessing the long term performance of waste disposal facility requires numerical simulation of saturated and unsaturated groundwater flow and contaminant transport. Complex numerical models have been developed to try to realistically simulate subsurface flow and transport processes. These models provide important information about system behavior and identify important processes, but may not be practical for demonstrating compliance with performance standards because of excessively long computer simulation times and input requirements. Two approaches to distilling the behavior of a complex model into simpler formulations that are practical for demonstrating compliance with performance objectives are examined in this paper. The first approach uses the information obtained from the complex model to develop a simple model that mimics the complex model behavior for stated performance objectives. The simple model may need to include essential processes that are important to assessing performance, such as time-variable infiltration and waste emplacement rates, subsurface heterogeneity, sorption, decay, and radioactive ingrowth. The approach was applied to a Low-Level Waste disposal site at the Idaho National Laboratory where a complex three dimensional vadose zone model was developed first to understand system behavior and important processes. The complex model was distilled down to a relatively simple one-dimensional vadose zone model and three-dimensional aquifer transport model. Comparisons between the simple model and complex model of vadose zone fluxes and groundwater concentrations showed relatively good agreement between the models for both fission and activation products (129I, 36Cl, 99Tc) and actinides (238U, 239Pu, 237Np). Application of the simple model allowed for Monte Carlo uncertainty analysis and simulations of numerous disposal and release scenarios. The second approach investigated was the response surface model. In the response surface model approach, the temporal response of a complex model to an instantaneously-released unit mass of a conservative tracer at a defined point is calculated and stored (the response function). A separate response function is needed for each source-receptor pair. The convolution of the response function and estimated contaminant flux from the source then provides an estimate of the media concentration. The response function approach has the advantage of incorporating all processes included in the complex model into a single discrete function that requires only one run of the complex model. Limitations to the response surface model include the assumption of uniform retardation in the model domain and the assumption that radioactive progeny travel at the same rate as their parent. In highly heterogeneous environments where uniform retardation cannot be assumed, contaminant-specific response functions can be calculated. The response surface model was applied to a two-dimensional regional aquifer model to simulate multiple plumes of tritium originating from multiple sources across the Idaho National Laboratory.

Download or read book Strategy and Methodology for Radioactive Waste Characterization written by International Atomic Energy Agency and published by IAEA. This book was released on 2007 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past decade significant progress has been achieved in the development of waste characterization and control procedures and equipment as a direct response to ever-increasing requirements for quality and reliability of information on waste characteristics. Failure in control procedures at any step can have important, adverse consequences and may result in producing waste packages which are not compliant with the waste acceptance criteria for disposal, thereby adversely impacting the repository. The information and guidance included in this publication corresponds to recent achievements and reflects the optimum approaches, thereby reducing the potential for error and enhancing the quality of the end product. -- Publisher's description.

Download or read book Explanation of Significant Differences Between Models Used to Assess Groundwater Impacts for the Disposal of Greater Than Class C Low Level Radioactive Waste and Greater Than Class C Like Waste Environmental Impact Statement DOE EIS 0375 D and the written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Models have been used to assess the groundwater impacts to support the Draft Environmental Impact Statement for the Disposal of Greater-Than-Class C (GTCC) Low-Level Radioactive Waste and GTCC-Like Waste (DOE-EIS 2011) for a facility sited at the Idaho National Laboratory and the Environmental Assessment for the INL Remote-Handled Low-Level Waste Disposal Project (INL 2011). Groundwater impacts are primarily a function of (1) location determining the geologic and hydrologic setting, (2) disposal facility configuration, and (3) radionuclide source, including waste form and release from the waste form. In reviewing the assumptions made between the model parameters for the two different groundwater impacts assessments, significant differences were identified. This report presents the two sets of model assumptions and discusses their origins and implications for resulting dose predictions. Given more similar model parameters, predicted doses would be commensurate.

Download or read book Auxiliary Analyses in Support of Performance Assessment of a Hypothetical Low level Waste Facility written by and published by . This book was released on 1995 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: A numerical model of multiphase air-water flow and contaminant transport in the unsaturated zone is presented. The multiphase flow equations are solved using the two-pressure, mixed form of the equations with a modified Picard linearization of the equations and a finite element spatial approximation. A volatile contaminant is assumed to be transported in either phase, or in both phases simultaneously. The contaminant partitions between phases with an equilibrium distribution given by Henry's Law or via kinetic mass transfer. The transport equations are solved using a Galerkin finite element method with reduced integration to lump the resultant matrices. The numerical model is applied to published experimental studies to examine the behavior of the air phase and associated contaminant movement under water infiltration. The model is also used to evaluate a hypothetical design for a low-level radioactive waste disposal facility. The model has been developed in both one and two dimensions; documentation and computer codes are available for the one-dimensional flow and transport model.

Download or read book Waste Forms Technology and Performance written by National Research Council and published by National Academies Press. This book was released on 2011-09-05 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Department of Energy's Office of Environmental Management (DOE-EM) is responsible for cleaning up radioactive waste and environmental contamination resulting from five decades of nuclear weapons production and testing. A major focus of this program involves the retrieval, processing, and immobilization of waste into stable, solid waste forms for disposal. Waste Forms Technology and Performance, a report requested by DOE-EM, examines requirements for waste form technology and performance in the cleanup program. The report provides information to DOE-EM to support improvements in methods for processing waste and selecting and fabricating waste forms. Waste Forms Technology and Performance places particular emphasis on processing technologies for high-level radioactive waste, DOE's most expensive and arguably most difficult cleanup challenge. The report's key messages are presented in ten findings and one recommendation.

Download or read book Development of a Comprehensive Source Term Model for the Subsurface Disposal Area at the Idaho National Engineering and Environmental Laboratory written by and published by . This book was released on 1997 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first detailed comprehensive simulation study to evaluate fate and transport of wastes disposed in the Subsurface Disposal Area (SDA), at the Radioactive Waste Management Complex (RWMC), Idaho National Engineering and Environmental Laboratory (INEEL) has recently been conducted. One of the most crucial parts of this modeling was the source term or release model. The current study used information collected over the last five years defining contaminant specific information including: the amount disposed, the waste form (physical and chemical properties) and the type of container used for each contaminant disposed. This information was used to simulate the release of contaminants disposed in the shallow subsurface at the SDA. The DUST-MS model was used to simulate the release. Modifications were made to allow the yearly disposal information to be incorporated. The modeling includes unique container and release rate information for each of the 42 years of disposal. The results from this simulation effort are used for both a groundwater and a biotic uptake evaluation. As part of this modeling exercise, inadequacies in the available data relating to the release of contaminants have been identified. The results from this modeling study have been used to guide additional data collection activities at the SDA for purposes of increasing confidence in the appropriateness of model predictions.

Download or read book ABSTRACTION OF INFORMATION FROM 2 AND 3 DIMENSIONAL PORFLOW MODELS INTO A 1 D GOLDSIM MODEL 11404 written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Savannah River National Laboratory has developed a 'hybrid' approach to Performance Assessment modeling which has been used for a number of Performance Assessments. This hybrid approach uses a multi-dimensional modeling platform (PorFlow) to develop deterministic flow fields and perform contaminant transport. The GoldSim modeling platform is used to develop the Sensitivity and Uncertainty analyses. Because these codes are performing complementary tasks, it is incumbent upon them that for the deterministic cases they produce very similar results. This paper discusses two very different waste forms, one with no engineered barriers and one with engineered barriers, each of which present different challenges to the abstraction of data. The hybrid approach to Performance Assessment modeling used at the SRNL uses a 2-D unsaturated zone (UZ) and a 3-D saturated zone (SZ) model in the PorFlow modeling platform. The UZ model consists of the waste zone and the unsaturated zoned between the waste zone and the water table. The SZ model consists of source cells beneath the waste form to the points of interest. Both models contain 'buffer' cells so that modeling domain boundaries do not adversely affect the calculation. The information pipeline between the two models is the contaminant flux. The domain contaminant flux, typically in units of moles (or Curies) per year from the UZ model is used as a boundary condition for the source cells in the SZ. The GoldSim modeling component of the hybrid approach is an integrated UZ-SZ model. The model is a 1-D representation of the SZ, typically 1-D in the UZ, but as discussed below, depending on the waste form being analyzed may contain pseudo-2-D elements. A waste form at the Savannah River Site (SRS) which has no engineered barriers is commonly referred to as a slit trench. A slit trench, as its name implies, is an unlined trench, typically 6 m deep, 6 m wide, and 200 m long. Low level waste consisting of soil, debris, rubble, wood, etc. is disposed within the trench which is then covered with soil and a cap. The filled trench resembles the surrounding soil, albeit with a higher porosity. As a result, the flow field through the trench is essentially 1-dimensional. This dimensionality makes the abstraction of information from this waste form fairly simple. Engineered waste forms present challenges not seen in the slit trench because of their higher dimensionality. Flow fields must conform to the barriers and are therefore subject to changes in direction. This paper will examine one case and show how this multidimensional flow field can be abstracted into a 1-dimensional flow field while retaining characteristics important to the transport of radioactive contaminants. One complication not addressed by the two preceding examples is that of multiple sources. This presents quite a challenge to the benchmarking exercise, but a fairly robust method has been developed to deal with it. While the PorFlow analyses can treat all sources as independent in space, this is not possible with a 1-D model. This problem has been addressed by constructing multiple 1-D models of the waste forms and using plume overlaps at the assessment points to address the multiple sources which can contribute to a distinct assessment point.

Download or read book EPA Publications Bibliography written by and published by . This book was released on 1983 with total page 1724 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Consolidates into one publication all reports previously published in the EPA publications bibliography quarterly abstract bulletin, from its inception in 1977 ..."--Foreword, 1977/1983.

Download or read book Evaluation of High level Waste Pretreatment Processes with an Approximate Reasoning Model written by and published by . This book was released on 1999 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of an approximate-reasoning (AR)-based model to analyze pretreatment options for high-level waste is presented. AR methods are used to emulate the processes used by experts in arriving at a judgment. In this paper, the authors first consider two specific issues in applying AR to the analysis of pretreatment options. They examine how to combine quantitative and qualitative evidence to infer the acceptability of a process result using the example of cesium content in low-level waste. They then demonstrate the use of simple physical models to structure expert elicitation and to produce inferences consistent with a problem involving waste particle size effects.

Download or read book Energy Research Abstracts written by and published by . This book was released on 1994-12 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book EPA Publications Bibliography 1984 1990 written by and published by . This book was released on 1990 with total page 1732 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book RCRA Ground water Monitoring Technical Enforcement Guidance Document TEGD written by and published by . This book was released on 1986 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book TIP 35 Enhancing Motivation for Change in Substance Use Disorder Treatment Updated 2019 written by U.S. Department of Health and Human Services and published by Lulu.com. This book was released on 2019-11-19 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: Motivation is key to substance use behavior change. Counselors can support clients' movement toward positive changes in their substance use by identifying and enhancing motivation that already exists. Motivational approaches are based on the principles of person-centered counseling. Counselors' use of empathy, not authority and power, is key to enhancing clients' motivation to change. Clients are experts in their own recovery from SUDs. Counselors should engage them in collaborative partnerships. Ambivalence about change is normal. Resistance to change is an expression of ambivalence about change, not a client trait or characteristic. Confrontational approaches increase client resistance and discord in the counseling relationship. Motivational approaches explore ambivalence in a nonjudgmental and compassionate way.

Download or read book Safe Management of Wastes from Health care Activities written by Yves Chartier and published by World Health Organization. This book was released on 2014 with total page 327 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the second edition of the WHO handbook on the safe, sustainable and affordable management of health-care waste--commonly known as "the Blue Book". The original Blue Book was a comprehensive publication used widely in health-care centers and government agencies to assist in the adoption of national guidance. It also provided support to committed medical directors and managers to make improvements and presented practical information on waste-management techniques for medical staff and waste workers. It has been more than ten years since the first edition of the Blue Book. During the intervening period, the requirements on generators of health-care wastes have evolved and new methods have become available. Consequently, WHO recognized that it was an appropriate time to update the original text. The purpose of the second edition is to expand and update the practical information in the original Blue Book. The new Blue Book is designed to continue to be a source of impartial health-care information and guidance on safe waste-management practices. The editors' intention has been to keep the best of the original publication and supplement it with the latest relevant information. The audience for the Blue Book has expanded. Initially, the publication was intended for those directly involved in the creation and handling of health-care wastes: medical staff, health-care facility directors, ancillary health workers, infection-control officers and waste workers. This is no longer the situation. A wider range of people and organizations now have an active interest in the safe management of health-care wastes: regulators, policy-makers, development organizations, voluntary groups, environmental bodies, environmental health practitioners, advisers, researchers and students. They should also find the new Blue Book of benefit to their activities. Chapters 2 and 3 explain the various types of waste produced from health-care facilities, their typical characteristics and the hazards these wastes pose to patients, staff and the general environment. Chapters 4 and 5 introduce the guiding regulatory principles for developing local or national approaches to tackling health-care waste management and transposing these into practical plans for regions and individual health-care facilities. Specific methods and technologies are described for waste minimization, segregation and treatment of health-care wastes in Chapters 6, 7 and 8. These chapters introduce the basic features of each technology and the operational and environmental characteristics required to be achieved, followed by information on the potential advantages and disadvantages of each system. To reflect concerns about the difficulties of handling health-care wastewaters, Chapter 9 is an expanded chapter with new guidance on the various sources of wastewater and wastewater treatment options for places not connected to central sewerage systems. Further chapters address issues on economics (Chapter 10), occupational safety (Chapter 11), hygiene and infection control (Chapter 12), and staff training and public awareness (Chapter 13). A wider range of information has been incorporated into this edition of the Blue Book, with the addition of two new chapters on health-care waste management in emergencies (Chapter 14) and an overview of the emerging issues of pandemics, drug-resistant pathogens, climate change and technology advances in medical techniques that will have to be accommodated by health-care waste systems in the future (Chapter 15).

Download or read book Health Effects Assessment Summary Tables written by and published by . This book was released on 1997 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Guide for the Care and Use of Laboratory Animals written by National Research Council and published by National Academies Press. This book was released on 2011-01-27 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: A respected resource for decades, the Guide for the Care and Use of Laboratory Animals has been updated by a committee of experts, taking into consideration input from the scientific and laboratory animal communities and the public at large. The Guide incorporates new scientific information on common laboratory animals, including aquatic species, and includes extensive references. It is organized around major components of animal use: Key concepts of animal care and use. The Guide sets the framework for the humane care and use of laboratory animals. Animal care and use program. The Guide discusses the concept of a broad Program of Animal Care and Use, including roles and responsibilities of the Institutional Official, Attending Veterinarian and the Institutional Animal Care and Use Committee. Animal environment, husbandry, and management. A chapter on this topic is now divided into sections on terrestrial and aquatic animals and provides recommendations for housing and environment, husbandry, behavioral and population management, and more. Veterinary care. The Guide discusses veterinary care and the responsibilities of the Attending Veterinarian. It includes recommendations on animal procurement and transportation, preventive medicine (including animal biosecurity), and clinical care and management. The Guide addresses distress and pain recognition and relief, and issues surrounding euthanasia. Physical plant. The Guide identifies design issues, providing construction guidelines for functional areas; considerations such as drainage, vibration and noise control, and environmental monitoring; and specialized facilities for animal housing and research needs. The Guide for the Care and Use of Laboratory Animals provides a framework for the judgments required in the management of animal facilities. This updated and expanded resource of proven value will be important to scientists and researchers, veterinarians, animal care personnel, facilities managers, institutional administrators, policy makers involved in research issues, and animal welfare advocates.

Download or read book Prudent Practices in the Laboratory written by National Research Council and published by National Academies Press. This book was released on 1995-09-16 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume updates and combines two National Academy Press bestsellers--Prudent Practices for Handling Hazardous Chemicals in Laboratories and Prudent Practices for Disposal of Chemicals from Laboratories--which have served for more than a decade as leading sources of chemical safety guidelines for the laboratory. Developed by experts from academia and industry, with specialties in such areas as chemical sciences, pollution prevention, and laboratory safety, Prudent Practices for Safety in Laboratories provides step-by-step planning procedures for handling, storage, and disposal of chemicals. The volume explores the current culture of laboratory safety and provides an updated guide to federal regulations. Organized around a recommended workflow protocol for experiments, the book offers prudent practices designed to promote safety and it includes practical information on assessing hazards, managing chemicals, disposing of wastes, and more. Prudent Practices for Safety in Laboratories is essential reading for people working with laboratory chemicals: research chemists, technicians, safety officers, chemistry educators, and students.