Download or read book Digital Circuit Design Laboratory Manual written by John Matthew Pavlina and published by . This book was released on 2020-05-23 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laboratory manual for Digital Circuit Design using Intel Quartus software. Suitable for online and in-person instruction. Required for Embry-Riddle Aeronautical University classes.Includes the following laboratories:1) Introduction to Digital Circuits Lab,2) FPGA Design Workflow,3) Combinational Logic Circuits,4) Seven-segment Display Logic,5) Combinational Logic using VHDL,6) Multiplexed Displays,7) Servo Motor Control,8) Accelerometer Interfacing,9) SPDT Switch Debouncing Multiplexers,10) Brushless DC Motor Control.Covers the following topics in the appendices: - Basic Electrical Components, - HDL Design Using Intel Quartus, - Using Symbolic Blocks in Intel Quartus, - Multiplexing, - Pulse Width Modulation PWM, - Functional Simulation using ModelSim.Has the following references in the appendices: - Development Board Pin Listings, - VHDL Source Code Listing, - Device Data

Download or read book Digital Circuit Design Laboratory Manual 5th Ed written by Akhan Almagambetov and published by . This book was released on 2020-04-26 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laboratory manual for Digital Circuit Design using Intel Quartus software. Suitable for online and in-person instruction. Required for Embry-Riddle Aeronautical University classes.

Download or read book Digital Circuit Design Laboratory Manual 4th edition Global written by Akhan Almagambetov and published by Lulu.com. This book was released on with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Digital Circuits Laboratory Manual written by Farzin Asadi and published by Springer Nature. This book was released on 2023-08-30 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital systems are an important part of modern life. This book introduces the basic building blocks of digital systems and how these blocks can be used to design a digital system. It can be used as a laboratory manual for courses such as Digital Logic and Digital Electronics. All of the experiments in this book can be done in a simulation environment like: Proteus® or NI® MultiSim® or on the breadboard in a real laboratory environment.

Download or read book ELECTRONICS LAB MANUAL VOLUME 2 written by NAVAS, K. A. and published by PHI Learning Pvt. Ltd.. This book was released on 2018-10-01 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is evolved from the experience of the author who taught all lab courses in his three decades of teaching in various universities in India. The objective of this lab manual is to provide information to undergraduate students to practice experiments in electronics laboratories. This book covers 118 experiments for linear/analog integrated circuits lab, communication engineering lab, power electronics lab, microwave lab and optical communication lab. The experiments described in this book enable the students to learn: • Various analog integrated circuits and their functions • Analog and digital communication techniques • Power electronics circuits and their functions • Microwave equipment and components • Optical communication devices This book is intended for the B.Tech students of Electronics and Communication Engineering, Electrical and Electronics Engineering, Biomedical Electronics, Instrumentation and Control, Computer Science, and Applied Electronics. It is designed not only for engineering students, but can also be used by BSc/MSc (Physics) and Diploma students. KEY FEATURES • Contains aim, components and equipment required, theory, circuit diagram, pin-outs of active devices, design, tables, graphs, alternate circuits, and troubleshooting techniques for each experiment • Includes viva voce and examination questions with their answers • Provides exposure on various devices TARGET AUDIENCE • B.Tech (Electronics and Communication Engineering, Electrical and Electronics Engineering, Biomedical Electronics, Instrumentation and Control, Computer Science, and Applied Electronics) • BSc/MSc (Physics) • Diploma (Engineering)

Download or read book Practical Design of Digital Circuits written by Ian Kampel and published by Elsevier. This book was released on 2015-08-11 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: Practical Design of Digital Circuits: Basic Logic to Microprocessors demonstrates the practical aspects of digital circuit design. The intention is to give the reader sufficient confidence to embark upon his own design projects utilizing digital integrated circuits as soon as possible. The book is organized into three parts. Part 1 teaches the basic principles of practical design, and introduces the designer to his ""tools"" — or rather, the range of devices that can be called upon. Part 2 shows the designer how to put these together into viable designs. It includes two detailed descriptions of actual design exercises. The first of these is a fairly simple exercise in CMOS design; the second is a much more complex design for an electronic game, using TTL devices. Part 3 focuses on microprocessors. It illustrates how a particular design problem changes emphasis when a microprocessor is introduced. This book is aimed at a fairly broad market: it is intended to aid the linear design engineer to cross the barrier into digital electronics; it should provide interesting supporting reading for students studying digital electronics from the more academic viewpoint; and it should enable the enthusiast to design much more ambitious and sophisticated projects than he could otherwise attempt if restricted to linear devices.

Download or read book Laboratory Manual for Electronic Devices and Circuits written by David A. Bell and published by Oxford University Press, USA. This book was released on 2001 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: This lab manual accompanies Electronic Devices and Circuits, 4/e.

Download or read book Introduction to Analog and Digital Circuits Lab Manual written by Brian DEAN and published by . This book was released on 2018-08-13 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fundamentals of Digital Electronics written by George B. Rutkowski and published by Prentice Hall. This book was released on 1985 with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Circuit Analysis Laboratory Workbook written by Teri L. Piatt and published by Morgan & Claypool Publishers. This book was released on 2017-06-15 with total page 127 pages. Available in PDF, EPUB and Kindle. Book excerpt: This workbook integrates theory with the concept of engineering design and teaches troubleshooting and analytical problem-solving skills. It is intended to either accompany or follow a first circuits course, and it assumes no previous experience with breadboarding or other lab equipment. This workbook uses only those components that are traditionally covered in a first circuits course (e.g., voltage sources, resistors, potentiometers, capacitors, and op amps) and gives students clear design goals, requirements, and constraints. Because we are using only components students have already learned how to analyze, they are able to tackle the design exercises, first working through the theory and math, then drawing and simulating their designs, and finally building and testing their designs on a breadboard.

Download or read book Digital Design written by Thomas Collins and published by . This book was released on 2009 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Lab Manual for Electronics written by Martin Feldman and published by Prentice Hall. This book was released on 2001-11 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: The emphasis is first on understanding the characteristics of basic circuits including resistors, capacitors, diodes, and bipolar and field effect transistors. The readers then use this understanding to construct more complex circuits such as power supplies, differential amplifiers, tuned circuit amplifiers, a transistor curve tracer, and a digital voltmeter. In addition, readers are exposed to special topics of current interest, such as the propagation and detection of signals through fiber optics, the use of Van der Pauw patterns for precise linewidth measurements, and high gain amplifiers based on active loads. KEY TOPICS: Chapter topics include Thevenin's Theorem; Resistive Voltage Division; Silicon Diodes; Resistor Capacitor Circuits; Half Wave Rectifiers; DC Power Supplies; Diode Applications; Bipolar Transistors; Field Effect Transistors; Characterization of Op-Amp Circuits; Transistor Curve Tracer; Introduction to PSPICE and AC Voltage Dividers; Characterization and Design of Emitter and Source Followers; Characterization and Design of an AC Variable Gain Amplifier; Design of Test Circuits for BJT's and FET's and Design of FET Ring Oscillators; Design and Characterization of Emitter Coupled Transistor Pairs; Tuned Amplifier and Oscillator; Design of Am Radio Frequency Transmitter and Receiver; Design of Oscillators Using Op-Amps; Current Mirrors and Active Loads; Sheet Resistance; Design of Analog Fiber Optic Transmission System; Digital Voltmeter.

Download or read book Experimenting with Digital Circuits written by Jack Cazes and published by . This book was released on 1973 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Digital Logic Design written by Ziad M Al-Asmer and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Lab Manual for Electronic Devices Global Edition written by THOMAS L. FLOYD and published by . This book was released on 2018-06-19 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: This laboratory manual is carefully coordinated to the text Electronic Devices, Tenth edition, Global edition, by Thomas L. Floyd. The seventeen experiments correspond to the chapters in the text (except the first experiment references Chapters 1 and the first part of Chapter 2). All of the experiments are subdivided into two or three "Parts." With one exception (Experiment 12-B), the Parts for the all experiments are completely independent of each other. The instructor can assign any or all Parts of these experiments, and in any order. This format provides flexibility depending on the schedule, laboratory time available, and course objectives. In addition, experiments 12 through 16 provide two options for experiments. These five experiments are divided into two major sections identified as A or B. The A experiments continue with the format of previous experiments; they are constructed with discrete components on standard protoboards as used in most electronic teaching laboratories. The A experiments can be assigned in programs where traditional devices are emphasized. Each B experiment has a similar format to the corresponding A experiment, but uses a programmable Analog Signal Processor (ASP) that is controlled by (free) Computer Aided Design (CAD) software from the Anadigm company (www.anadigm.com). These experiments support the Programmable Analog Design feature in the textbook. The B experiments are also subdivided into independent Parts, but Experiment 12-B, Part 1, is a software tutorial and should be performed before any other B experiments. This is an excellent way to introduce the ASP technology because no other hardware is required other than a computer running the downloaded software. In addition to Experiment 12-B, the first 13 steps of Experiment 15-B, Part 2, are also tutorial in nature for the AnadigmFilter program. This is an amazing active filter design tool that is easy to learn and is included with the AnadigmDesigner2 (AD2) CAD software. The ASP is part of a Programmable Analog Module (PAM) circuit board from the Servenger company (www.servenger.com) that interfaces to a personal computer. The PAM is controlled by the AD2 CAD software from the Anadigm company website. Except for Experiment 12-B, Part 1, it is assumed that the PAM is connected to the PC and AnadigmDesigner2 is running. Experiment 16-B, Part 3, also requires a spreadsheet program such as Microsoft® Excel®. The PAM is described in detail in the Quick Start Guide (Appendix B). Instructors may choose to mix A and B experiments with no loss in continuity, depending on course objectives and time. We recommend that Experiment 12-B,Part 1, be assigned if you want students to have an introduction to the ASP without requiring a hardware purchase. A text feature is the Device Application (DA) at the end of most chapters. All of the DAs have a related laboratory exercise using a similar circuit that is sometimes simplified to make laboratory time as efficient as possible. The same text icon identifies the related DA exercise in the lab manual. One issue is the trend of industry to smaller surface-mount devices, which are very difficult to work with and are not practical for most lab work. For example, almost all varactors are supplied as surface mount devices now. In reviewing each experiment, we have found components that can illustrate the device function with a traditional one. The traditional through-hole MV2109 varactor is listed as obsolete, but will be available for the foreseeable future from Electronix Express (www.elexp.com), so it is called out in Experiment 3. All components are available from Electronix Express (www.elexp.com) as a kit of parts (see list in Appendix A). The format for each experiment has not changed from the last edition and is as follows: · Introduction: A brief discussion about the experiment and comments about each of the independent Parts that follow. · Reading: Reading assignment in the Floyd text related to the experiment. · Key Objectives: A statement specific to each Part of the experiment of what the student should be able to do. · Components Needed: A list components and small items required for each Part but not including the equipment found at a typical lab station. Particular care has been exercised to select materials that are readily available and reusable, keeping cost at a minimum. · Parts: There are two or three independent parts to each experiment. Needed tables, graphs, and figures are positioned close to the first referenced location to avoid confusion. Step numbering starts fresh with each Part, but figures and tables are numbered sequentially for the entire experiment to avoid multiple figures with the same number. § Conclusion: At the end of each Part, space is provided for a written conclusion. § Questions: Each Part includes several questions that require the student to draw upon the laboratory work and check his or her understanding of the concepts. Troubleshooting questions are frequently presented. · Multisim Simulation: At the end of each A experiment (except #1), one or more circuits are simulated in a Multisim computer simulation. New Multisim troubleshooting problems have been added to this edition. Multisim troubleshooting files are identified with the suffix f1, f2, etc., in the file name (standing for fault1, fault2, etc.). Other files, with nf as the suffix include demonstrations or practice using instruments such as the Bode Plotter and the Spectrum Analyzer. A special icon is shown with all figures that are related to the Multisim simulation. Multisim files are found on the website: www.pearsonglobaledition.com/Floyd. Microsoft PowerPoint® slides are available at no cost to instructors for all experiments. The slides reinforce the experiments with troubleshooting questions and a related problem and are available on the instructor''s resource site. Each laboratory station should contain a dual-variable regulated power supply, a function generator, a multimeter, and a dual-channel oscilloscope. A list of all required materials is given in Appendix A along with information on acquiring the PAM. As mentioned, components are also available as a kit from Electronix Express; the kit number is 32DBEDFL10.

Download or read book Laboratory Manual for Electronic Circuits 1 written by Murat AKSOY and published by Akademisyen Kitabevi. This book was released on 2018-10-31 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Digital Electronics written by Cherry Bhargava and published by . This book was released on 2020-06 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: