Download or read book Modelling Spark Ignition Combustion written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modeling of End Gas Autoignition for Knock Prediction in Gasoline Engines written by Andreas Manz and published by Logos Verlag Berlin GmbH. This book was released on 2016-08-18 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: Downsizing of modern gasoline engines with direct injection is a key concept for achieving future CO22 emission targets. However, high power densities and optimum efficiency are limited by an uncontrolled autoignition of the unburned air-fuel mixture, the so-called spark knock phenomena. By a combination of three-dimensional Computational Fluid Dynamics (3D-CFD) and experiments incorporating optical diagnostics, this work presents an integral approach for predicting combustion and autoignition in Spark Ignition (SI) engines. The turbulent premixed combustion and flame front propagation in 3D-CFD is modeled with the G-equation combustion model, i.e. a laminar flamelet approach, in combination with the level set method. Autoignition in the unburned gas zone is modeled with the Shell model based on reduced chemical reactions using optimized reaction rate coefficients for different octane numbers (ON) as well as engine relevant pressures, temperatures and EGR rates. The basic functionality and sensitivities of improved sub-models, e.g. laminar flame speed, are proven in simplified test cases followed by adequate engine test cases. It is shown that the G-equation combustion model performs well even on unstructured grids with polyhedral cells and coarse grid resolution. The validation of the knock model with respect to temporal and spatial knock onset is done with fiber optical spark plug measurements and statistical evaluation of individual knocking cycles with a frequency based pressure analysis. The results show a good correlation with the Shell autoignition relevant species in the simulation. The combined model approach with G-equation and Shell autoignition in an active formulation enables a realistic representation of thin flame fronts and hence the thermodynamic conditions prior to knocking by taking into account the ignition chemistry in unburned gas, temperature fluctuations and self-acceleration effects due to pre-reactions. By the modeling approach and simulation methodology presented in this work the overall predictive capability for the virtual development of future knockproof SI engines is improved.
Download or read book Internal Combustion Engine Fundamentals 2E written by John Heywood and published by McGraw Hill Professional. This book was released on 2018-05-01 with total page 1055 pages. Available in PDF, EPUB and Kindle. Book excerpt: Publisher's Note: Products purchased from Third Party sellers are not guaranteed by the publisher for quality, authenticity, or access to any online entitlements included with the product. The long-awaited revision of the most respected resource on Internal Combustion Engines --covering the basics through advanced operation of spark-ignition and diesel engines. Written by one of the most recognized and highly regarded names in internal combustion engines this trusted educational resource and professional reference covers the key physical and chemical processes that govern internal combustion engine operation and design. Internal Combustion Engine Fundamentals, Second Edition, has been thoroughly revised to cover recent advances, including performance enhancement, efficiency improvements, and emission reduction technologies. Highly illustrated and cross referenced, the book includes discussions of these engines’ environmental impacts and requirements. You will get complete explanations of spark-ignition and compression-ignition (diesel) engine operating characteristics as well as of engine flow and combustion phenomena and fuel requirements. Coverage includes: • Engine types and their operation • Engine design and operating parameters • Thermochemistry of fuel-air mixtures • Properties of working fluids • Ideal models of engine cycles • Gas exchange processes • Mixture preparation in spark-ignition engines • Charge motion within the cylinder • Combustion in spark-ignition engines • Combustion in compression-ignition engines • Pollutant formation and control • Engine heat transfer • Engine friction and lubrication • Modeling real engine flow and combustion processes • Engine operating characteristics
Download or read book Turbulent Combustion written by Norbert Peters and published by Cambridge University Press. This book was released on 2000-08-15 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: The combustion of fossil fuels remains a key technology for the foreseeable future. It is therefore important that we understand the mechanisms of combustion and, in particular, the role of turbulence within this process. Combustion always takes place within a turbulent flow field for two reasons: turbulence increases the mixing process and enhances combustion, but at the same time combustion releases heat which generates flow instability through buoyancy, thus enhancing the transition to turbulence. The four chapters of this book present a thorough introduction to the field of turbulent combustion. After an overview of modeling approaches, the three remaining chapters consider the three distinct cases of premixed, non-premixed, and partially premixed combustion, respectively. This book will be of value to researchers and students of engineering and applied mathematics by demonstrating the current theories of turbulent combustion within a unified presentation of the field.
Download or read book Recent Advances in the Aerospace Sciences written by Corrado Casci and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 438 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume, published in honor of Prof. Luigi Crocco, appears when Luigi Crocco celebrates his 75th birthday of a life devoted to study, research, and teaching. The events in his life and World War II forced Luigi Crocco, as well as other Italian scientists, to look to foreign countries for the calm haven so vital to study. This notwithstanding, his scientific activity was never inter rupted, and this volume is an acknowledgment of scientists and researchers to his work and life. Prefazione Questo volume in onore del prof. ing. Luigi Crocco vede la luce quando Luigi Crocco compie i 75 anni di una vita dedicata allo studio, alia ricerca e all'insegnamento. a Le vicende della vita, ed anche della 2 guerra mondiale, hanno costretto Luigi Crocco, come altri scienziati italiani, a dover cercare in altri Paesi quella serenita necessaria per dedicarsi allo studio. Ma la sua attivita scientifica non ha avuto interruzioni e questo volume essere la testimonianza di studiosi e di ricercatori alia sua opera e alia sua vita."
Download or read book Modeling Engine Spray and Combustion Processes written by Gunnar Stiesch and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt: The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Download or read book Encyclopedia of Automotive Engineering written by and published by John Wiley & Sons. This book was released on 2015-03-23 with total page 3888 pages. Available in PDF, EPUB and Kindle. Book excerpt: Erstmals eine umfassende und einheitliche Wissensbasis und Grundlage für weiterführende Studien und Forschung im Bereich der Automobiltechnik. Die Encyclopedia of Automotive Engineering ist die erste umfassende und einheitliche Wissensbasis dieses Fachgebiets und legt den Grundstein für weitere Studien und tiefgreifende Forschung. Weitreichende Querverweise und Suchfunktionen ermöglichen erstmals den zentralen Zugriff auf Detailinformationen zu bewährten Branchenstandards und -verfahren. Zusammenhängende Konzepte und Techniken aus Spezialbereichen lassen sich so einfacher verstehen. Neben traditionellen Themen des Fachgebiets beschäftigt sich diese Enzyklopädie auch mit "grünen" Technologien, dem Übergang von der Mechanik zur Elektronik und den Möglichkeiten zur Herstellung sicherer, effizienterer Fahrzeuge unter weltweit unterschiedlichen wirtschaftlichen Rahmenbedingungen. Das Referenzwerk behandelt neun Hauptbereiche: (1) Motoren: Grundlagen; (2) Motoren: Design; (3) Hybrid- und Elektroantriebe; (4) Getriebe- und Antriebssysteme; (5) Chassis-Systeme; (6) Elektrische und elektronische Systeme; (7) Karosserie-Design; (8) Materialien und Fertigung; (9) Telematik. - Zuverlässige Darstellung einer Vielzahl von Spezialthemen aus dem Bereich der Automobiltechnik. - Zugängliches Nachschlagewerk für Jungingenieure und Studenten, die die technologischen Grundlagen besser verstehen und ihre Kenntnisse erweitern möchten. - Wertvolle Verweise auf Detailinformationen und Forschungsergebnisse aus der technischen Literatur. - Entwickelt in Zusammenarbeit mit der FISITA, der Dachorganisation nationaler Automobil-Ingenieur-Verbände aus 37 Ländern und Vertretung von über 185.000 Ingenieuren aus der Branche. - Erhältlich als stets aktuelle Online-Ressource mit umfassenden Suchfunktionen oder als Print-Ausgabe in sechs Bänden mit über 4.000 Seiten. Ein wichtiges Nachschlagewerk für Bibliotheken und Informationszentren in der Industrie, bei Forschungs- und Schulungseinrichtungen, Fachgesellschaften, Regierungsbehörden und allen Ingenieurstudiengängen. Richtet sich an Fachingenieure und Techniker aus der Industrie, Studenten höherer Semester und Studienabsolventen, Forscher, Dozenten und Ausbilder, Branchenanalysen und Forscher.
Download or read book Ignition by Hot Gas Jets written by Rajesh Sadanandan and published by . This book was released on 2007 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Computational Techniques for Multiphase Flows written by Guan Heng Yeoh and published by Elsevier. This book was released on 2009-10-07 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mixed or multiphase flows of solid/liquid or solid/gas are commonly found in many industrial fields, and their behavior is complex and difficult to predict in many cases. The use of computational fluid dynamics (CFD) has emerged as a powerful tool for the understanding of fluid mechanics in multiphase reactors, which are widely used in the chemical, petroleum, mining, food, beverage and pharmaceutical industries. Computational Techniques for Multiphase Flows enables scientists and engineers to the undertand the basis and application of CFD in muliphase flow, explains how to use the technique, when to use it and how to interpret the results and apply them to improving aplications in process enginering and other multiphase application areas including the pumping, automotive and energy sectors. - Understandable guide to a complex subject - Important in many industries - Ideal for potential users of CFD
Download or read book Lees Process Safety Essentials written by Sam Mannan and published by Butterworth-Heinemann. This book was released on 2013-11-12 with total page 570 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lees' Process Safety Essentials is a single-volume digest presenting the critical, practical content from Lees' Loss Prevention for day-to-day use and reference. It is portable, authoritative, affordable, and accessible — ideal for those on the move, students, and individuals without access to the full three volumes of Lees'. This book provides a convenient summary of the main content of Lees', primarily drawn from the hazard identification, assessment, and control content of volumes one and two. Users can access Essentials for day-to-day reference on topics including plant location and layout; human factors and human error; fire, explosion and toxic release; engineering for sustainable development; and much more. This handy volume is a valuable reference, both for students or early-career professionals who may not need the full scope of Lees', and for more experienced professionals needing quick, convenient access to information. - Boils down the essence of Lees'—the process safety encyclopedia trusted worldwide for over 30 years - Provides safety professionals with the core information they need to understand the most common safety and loss prevention challenges - Covers the latest standards and presents information, including recent incidents such as Texas City and Buncefield
Download or read book Turbulent Premixed Flames written by Nedunchezhian Swaminathan and published by Cambridge University Press. This book was released on 2011-04-25 with total page 447 pages. Available in PDF, EPUB and Kindle. Book excerpt: A work on turbulent premixed combustion is important because of increased concern about the environmental impact of combustion and the search for new combustion concepts and technologies. An improved understanding of lean fuel turbulent premixed flames must play a central role in the fundamental science of these new concepts. Lean premixed flames have the potential to offer ultra-low emission levels, but they are notoriously susceptible to combustion oscillations. Thus, sophisticated control measures are inevitably required. The editors' intent is to set out the modeling aspects in the field of turbulent premixed combustion. Good progress has been made on this topic, and this cohesive volume contains contributions from international experts on various subtopics of the lean premixed flame problem.
Download or read book A Level Set Based Flamelet Model for the Prediction of Combustion in Homogeneous Charge and Direct Injection Spark Ignition Engines written by Jens Ewald and published by . This book was released on 2006 with total page 165 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Mathematics of Combustion written by John D. Buckmaster and published by SIAM. This book was released on 1985-01-01 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book delves into the rapidly changing area of combustion, in which asymptotic methods and bifurcation theory have made a significant impact as have the constant-density, small-heat-release models and other important contributions.
Download or read book Particle Image Velocimetry written by Andreas Schröder and published by Springer Science & Business Media. This book was released on 2008-01-14 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book summarizes the main results reached using the EC-funded network PivNet 2. It also presents a survey of the state of the art of scientific research using PIV techniques. You get a clear introduction to the basics of these techniques. The authors then guide you through current and possible future applications for flow analysis, including combustion and supersonic flow. Hundreds of illustrations, many in full color, are provided.
Download or read book OpenFOAM written by J. Miguel Nóbrega and published by Springer. This book was released on 2019-01-24 with total page 527 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains selected papers of the 11th OpenFOAM® Workshop that was held in Guimarães, Portugal, June 26 - 30, 2016. The 11th OpenFOAM® Workshop had more than 140 technical/scientific presentations and 30 courses, and was attended by circa 300 individuals, representing 180 institutions and 30 countries, from all continents. The OpenFOAM® Workshop provided a forum for researchers, industrial users, software developers, consultants and academics working with OpenFOAM® technology. The central part of the Workshop was the two-day conference, where presentations and posters on industrial applications and academic research were shown. OpenFOAM® (Open Source Field Operation and Manipulation) is a free, open source computational toolbox that has a larger user base across most areas of engineering and science, from both commercial and academic organizations. As a technology, OpenFOAM® provides an extensive range of features to solve anything from complex fluid flows involving chemical reactions, turbulence and heat transfer, to solid dynamics and electromagnetics, among several others. Additionally, the OpenFOAM technology offers complete freedom to customize and extend its functionalities.
Download or read book Nanomaterials in Diagnostic Tools and Devices written by Suvardhan Kanchi and published by Elsevier. This book was released on 2020-06-05 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanomaterials in Diagnostic Tools and Devices provides a complete overview of the significance of nanomaterials in fabricating selective and performance enhanced nanodevices. It is an interdisciplinary reference that includes contributing subjects from nanomaterials, biosensors, materials science, biomedical instrumentation and medicinal chemistry. This book is authored by experts in the field of nanomaterial synthesis, modeling, and biosensor applications, and provides insight to readers working in various science fields on the latest advancements in smart and miniaturized nanodevices. These devices enable convenient real-time diagnosis of diseases at clinics rather than laboratories, and include implantable devices that cause less irritation and have improved functionality. Research in the field of nanomaterials is growing rapidly, creating a significant impact across different science disciplines and nanotechnology industries. This synthesis and modeling of nanomaterials has led to many technology breakthroughs and applications, especially in medical science.
Download or read book The Molecular Theory of Gases and Liquids written by Joseph O. Hirschfelder and published by John Wiley & Sons. This book was released on 1964-01-15 with total page 1283 pages. Available in PDF, EPUB and Kindle. Book excerpt: An essential cross-disciplinary reference for molecular interactions Molecular Theory of Gases and Liquids offers a rigorous, comprehensive treatment of molecular characteristics and behaviors in the gaseous and fluid states. A unique cross-disciplinary approach provides useful insight for students of chemistry, chemical engineering, fluid dynamics, and a variety of related fields, with thorough derivations and in-depth explanations throughout. Appropriate for graduate students and working scientists alike, this book details advanced concepts without sacrificing depth of coverage or technical detail.
