Download or read book Design Simulation and Applications of Inductors and Transformers for Si RF ICs written by Ali M. Niknejad and published by Springer Science & Business Media. This book was released on 2005-12-15 with total page 193 pages. Available in PDF, EPUB and Kindle. Book excerpt: The modern wireless communication industry has put great demands on circuit designers for smaller, cheaper transceivers in the gigahertz frequency range. One tool which has assisted designers in satisfying these requirements is the use of on-chip inductiveelements (inductors and transformers) in silicon (Si) radio-frequency (RF) integrated circuits (ICs). These elements allow greatly improved levels of performance in Si monolithic low-noise amplifiers, power amplifiers, up-conversion and down-conversion mixers and local oscillators. Inductors can be used to improve the intermodulation distortion performance and noise figure of small-signal amplifiers and mixers. In addition, the gain of amplifier stages can be enhanced and the realization of low-cost on-chip local oscillators with good phase noise characteristics is made feasible. In order to reap these benefits, it is essential that the IC designer be able to predict and optimize the characteristics of on-chip inductiveelements. Accurate knowledge of inductance values, quality factor (Q) and the influence of ad- cent elements (on-chip proximity effects) and substrate losses is essential. In this book the analysis, modeling and application of on-chip inductive elements is considered. Using analyses based on Maxwells equations, an accurate and efficient technique is developed to model these elements over a wide frequency range. Energy loss to the conductive substrate is modeled through several mechanisms, including electrically induced displacement and conductive c- rents and by magnetically induced eddy currents. These techniques have been compiled in a user-friendly software tool ASITIC (Analysis and Simulation of Inductors and Transformers for Integrated Circuits).

Download or read book Microwave Circuit Design Using Linear and Nonlinear Techniques written by George D. Vendelin and published by John Wiley & Sons. This book was released on 2005-10-03 with total page 1080 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ultimate handbook on microwave circuit design with CAD. Full of tips and insights from seasoned industry veterans, Microwave Circuit Design offers practical, proven advice on improving the design quality of microwave passive and active circuits-while cutting costs and time. Covering all levels of microwave circuit design from the elementary to the very advanced, the book systematically presents computer-aided methods for linear and nonlinear designs used in the design and manufacture of microwave amplifiers, oscillators, and mixers. Using the newest CAD tools, the book shows how to design transistor and diode circuits, and also details CAD's usefulness in microwave integrated circuit (MIC) and monolithic microwave integrated circuit (MMIC) technology. Applications of nonlinear SPICE programs, now available for microwave CAD, are described. State-of-the-art coverage includes microwave transistors (HEMTs, MODFETs, MESFETs, HBTs, and more), high-power amplifier design, oscillator design including feedback topologies, phase noise and examples, and more. The techniques presented are illustrated with several MMIC designs, including a wideband amplifier, a low-noise amplifier, and an MMIC mixer. This unique, one-stop handbook also features a major case study of an actual anticollision radar transceiver, which is compared in detail against CAD predictions; examples of actual circuit designs with photographs of completed circuits; and tables of design formulae.

Download or read book Silicon Heterostructure Handbook written by John D. Cressler and published by CRC Press. This book was released on 2018-10-03 with total page 1248 pages. Available in PDF, EPUB and Kindle. Book excerpt: An extraordinary combination of material science, manufacturing processes, and innovative thinking spurred the development of SiGe heterojunction devices that offer a wide array of functions, unprecedented levels of performance, and low manufacturing costs. While there are many books on specific aspects of Si heterostructures, the Silicon Heterostructure Handbook: Materials, Fabrication, Devices, Circuits, and Applications of SiGe and Si Strained-Layer Epitaxy is the first book to bring all aspects together in a single source. Featuring broad, comprehensive, and in-depth discussion, this handbook distills the current state of the field in areas ranging from materials to fabrication, devices, CAD, circuits, and applications. The editor includes "snapshots" of the industrial state-of-the-art for devices and circuits, presenting a novel perspective for comparing the present status with future directions in the field. With each chapter contributed by expert authors from leading industrial and research institutions worldwide, the book is unequalled not only in breadth of scope, but also in depth of coverage, timeliness of results, and authority of references. It also includes a foreword by Dr. Bernard S. Meyerson, a pioneer in SiGe technology. Containing nearly 1000 figures along with valuable appendices, the Silicon Heterostructure Handbook authoritatively surveys materials, fabrication, device physics, transistor optimization, optoelectronics components, measurement, compact modeling, circuit design, and device simulation.

Download or read book Fabrication of SiGe HBT BiCMOS Technology written by John D. Cressler and published by CRC Press. This book was released on 2018-10-03 with total page 321 pages. Available in PDF, EPUB and Kindle. Book excerpt: SiGe HBT BiCMOS technology is the obvious groundbreaker of the Si heterostructures application space. To date virtually every major player in the communications electronics market either has SiGe up and running in-house or is using someone else’s SiGe fab as foundry for their designers. Key to this success lies in successful integration of the SiGe HBT and Si CMOS, with no loss of performance from either device. Filled with contributions from leading experts, Fabrication of SiGe HBT BiCMOS Technologies brings together a complete discussion of these topics into a single resource. Drawn from the comprehensive and well-reviewed Silicon Heterostructure Handbook, this volume examines the design, fabrication, and application of silicon heterostructure transistors. A novel aspect of this book the inclusion of numerous snapshot views of the industrial state-of-the-art for SiGe HBT BiCMOS technology. It has been carefully designed to provide a useful basis of comparison for the current status and future course of the global industry. In addition to the copious technical material and the numerous references contained in each chapter, the book includes easy-to-reference appendices on the properties of Si and Ge, the generalized Moll-Ross relations, integral charge-control relations, and sample SiGe HBT compact model parameters.

Download or read book Integrated Inductors and Transformers written by Egidio Ragonese and published by CRC Press. This book was released on 2010-11-15 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: With the ability to improve performance, reduce fabrication costs, and increase integration levels of both RX and TX sections of the RF/mm-wave front-end, passive inductive components have experienced extraordinary growth in ICs. Therefore, a fundamental understanding of monolithic inductors and transformers has become essential for all process eng

Download or read book On Wafer Microwave Measurements and De embedding written by Errikos Lourandakis and published by Artech House. This book was released on 2016-07-31 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new authoritative resource presents the basics of network analyzer measurement equipment and troubleshooting errors involved in the on-wafer microwave measurement process. This book bridges the gap between theoretical and practical information using real-world practices that address all aspects of on-wafer passive device characterization in the microwave frequency range up to 60GHz. Readers find data and measurements from silicon integrated passive devices fabricated and tested in advance CMOS technologies. Basic circuit equations, terms and fundamentals of time and frequency domain analysis are covered. This book also explores the basics of vector network analyzers (VNA), two port S-parameter measurement routines, signal flow graphs, network theory, error models and VNA calibrations with the use of calibration standards.

Download or read book Power Amplifiers for the S C X and Ku bands written by Mladen Božanić and published by Springer. This book was released on 2015-12-29 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a detailed review of power amplifiers, including classes and topologies rarely covered in books, and supplies sufficient information to allow the reader to design an entire amplifier system, and not just the power amplification stage. A central aim is to furnish readers with ideas on how to simplify the design process for a preferred power amplifier stage by introducing software-based routines in a programming language of their choice. The book is in two parts, the first focusing on power amplifier theory and the second on EDA concepts. Readers will gain enough knowledge of RF and microwave transmission theory, principles of active and passive device design and manufacturing, and power amplifier design concepts to allow them to quickly create their own programs, which will help to accelerate the transceiver design process. All circuit designers facing the challenge of designing an RF or microwave power amplifier for frequencies from 2 to 18 GHz will find this book to be a valuable asset.

Download or read book FinFET Modeling for IC Simulation and Design written by Yogesh Singh Chauhan and published by Academic Press. This book was released on 2015-03-17 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the first to explain FinFET modeling for IC simulation and the industry standard – BSIM-CMG - describing the rush in demand for advancing the technology from planar to 3D architecture, as now enabled by the approved industry standard. The book gives a strong foundation on the physics and operation of FinFET, details aspects of the BSIM-CMG model such as surface potential, charge and current calculations, and includes a dedicated chapter on parameter extraction procedures, providing a step-by-step approach for the efficient extraction of model parameters. With this book you will learn: Why you should use FinFET The physics and operation of FinFET Details of the FinFET standard model (BSIM-CMG) Parameter extraction in BSIM-CMG FinFET circuit design and simulation Authored by the lead inventor and developer of FinFET, and developers of the BSIM-CM standard model, providing an experts’ insight into the specifications of the standard The first book on the industry-standard FinFET model - BSIM-CMG

Download or read book Linear CMOS RF Power Amplifiers for Wireless Applications written by Paulo Augusto Dal Fabbro and published by Springer Science & Business Media. This book was released on 2010-06-22 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in electronics have pushed mankind to create devices, ranging from - credible gadgets to medical equipment to spacecraft instruments. More than that, modern society is getting used to—if not dependent on—the comfort, solutions, and astonishing amount of information brought by these devices. One ?eld that has continuously bene?tted from those advances is the radio frequency integrated c- cuit (RFIC) design, which in its turn has promoted countless bene?ts to the mankind as a payback. Wireless communications is one prominent example of what the - vances in electronics have enabled and their consequences to our daily life. How could anyone back in the eighties think of the possibilities opened by the wireless local area networks (WLANs) that can be found today in a host of places, such as public libraries, coffee shops, trains, to name just a few? How can a youngster, who lives this true WLAN experience nowadays, imagine a world without it? This book dealswith the design oflinearCMOS RF PowerAmpli?ers(PAs). The RF PA is a very important part of the RF transceiver, the device that enables wireless communications. Two important aspects that are key to keep the advances in RF PA design at an accelerate pace are treated: ef?ciency enhancement and frequen- tunable capability. For this purpose, the design of two different integrated circuits realizedina0. 11μmtechnologyispresented,eachoneaddressingadifferentaspect. With respect to ef?ciency enhancement, the design of a dynamic supply RF power ampli?er is treated, making up the material of Chaps. 2 to 4.

Download or read book Design and Analysis of Spiral Inductors written by Genemala Haobijam and published by Springer Science & Business Media. This book was released on 2013-09-07 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book addresses the critical challenges faced by the ever-expanding wireless communication market and the increasing frequency of operation due to continuous innovation of high performance integrated passive devices. The challenges like low quality factor, design complexity, manufacturability, processing cost, etc., are studied with examples and specifics. Silicon on-chip inductor was first reported in 1990 by Nguyen and Meyer in a 0.8 μm silicon bipolar complementary metal oxide semiconductor technology (BiCMOS). Since then, there has been an enormous progress in the research on the performance trends, design and optimization, modeling, quality factor enhancement techniques, etc., of spiral inductors and significant results are reported in literature for various applications. This book introduces an efficient method of determining the optimized layout of on chip spiral inductor. The important fundamental tradeoffs of the design like quality factor and area, quality factor and inductance, quality factor and operating frequency, maximum quality factor and the peak frequency is also explored. The authors proposed an algorithm for accurate design and optimization of spiral inductors using a 3D electromagnetic simulator with minimum number of inductor structure simulations and thereby reducing its long computation time. A new multilayer pyramidal symmetric inductor structure is also proposed in this book. Being multilevel, the proposed inductor achieves high inductance to area ratio and hence occupies smaller silicon area.

Download or read book Fast Techniques for Integrated Circuit Design written by Mikael Sahrling and published by Cambridge University Press. This book was released on 2019-08-15 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: Learn how to use estimation techniques to solve real-world IC design problems and accelerate design processes with this practical guide.

Download or read book The Circuits and Filters Handbook written by Wai-Kai Chen and published by CRC Press. This book was released on 2002-12-23 with total page 3076 pages. Available in PDF, EPUB and Kindle. Book excerpt: A bestseller in its first edition, The Circuits and Filters Handbook has been thoroughly updated to provide the most current, most comprehensive information available in both the classical and emerging fields of circuits and filters, both analog and digital. This edition contains 29 new chapters, with significant additions in the areas of computer-

Download or read book Automated Design of Analog and High frequency Circuits written by Bo Liu and published by Springer. This book was released on 2013-08-16 with total page 243 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computational intelligence techniques are becoming more and more important for automated problem solving nowadays. Due to the growing complexity of industrial applications and the increasingly tight time-to-market requirements, the time available for thorough problem analysis and development of tailored solution methods is decreasing. There is no doubt that this trend will continue in the foreseeable future. Hence, it is not surprising that robust and general automated problem solving methods with satisfactory performance are needed.

Download or read book Fundamentals of Circuits and Filters written by Wai-Kai Chen and published by CRC Press. This book was released on 2018-10-08 with total page 1034 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume, drawn from the Circuits and Filters Handbook, focuses on mathematics basics; circuit elements, devices, and their models; and linear circuit analysis. It examines Laplace transformation, Fourier methods for signal analysis and processing, z-transform, and wavelet transforms. It also explores network laws and theorems, terminal and port represetnation, analysis in the frequency domain, and more.

Download or read book The Circuits and Filters Handbook Five Volume Slipcase Set written by Wai-Kai Chen and published by CRC Press. This book was released on 2018-12-14 with total page 3364 pages. Available in PDF, EPUB and Kindle. Book excerpt: Standard-setting, groundbreaking, authoritative, comprehensive—these often overused words perfectly describe The Circuits and Filters Handbook, Third Edition. This standard-setting resource has documented the momentous changes that have occurred in the field of electrical engineering, providing the most comprehensive coverage available. More than 150 contributing experts offer in-depth insights and enlightened perspectives into standard practices and effective techniques that will make this set the first—and most likely the only—tool you select to help you with problem solving. In its third edition, this groundbreaking bestseller surveys accomplishments in the field, providing researchers and designers with the comprehensive detail they need to optimize research and design. All five volumes include valuable information on the emerging fields of circuits and filters, both analog and digital. Coverage includes key mathematical formulas, concepts, definitions, and derivatives that must be mastered to perform cutting-edge research and design. The handbook avoids extensively detailed theory and instead concentrates on professional applications, with numerous examples provided throughout. The set includes more than 2500 illustrations and hundreds of references. Available as a comprehensive five-volume set, each of the subject-specific volumes can also be purchased separately.

Download or read book Proceedings of the 2nd International Conference on Communication Devices and Computing written by Sumit Kundu and published by Springer Nature. This book was released on 2019-12-16 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers high-quality papers presented at the 2nd International Conference on Communication, Devices & Computing (ICCDC 2019), held at Haldia Institute of Technology from March 14–15, 2019. The papers are divided into three main areas: communication technologies, electronics circuits & devices and computing. Written by students and researchers from around the world, they accurately reflect the global status quo.

Download or read book Electromagnetics for High Speed Analog and Digital Communication Circuits written by Ali M. Niknejad and published by Cambridge University Press. This book was released on 2007-02-22 with total page 465 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern communications technology demands smaller, faster and more efficient circuits. This book reviews the fundamentals of electromagnetism in passive and active circuit elements, highlighting various effects and potential problems in designing a new circuit. The author begins with a review of the basics - the origin of resistance, capacitance, and inductance - then progresses to more advanced topics such as passive device design and layout, resonant circuits, impedance matching, high-speed switching circuits, and parasitic coupling and isolation techniques. Using examples and applications in RF and microwave systems, the author describes transmission lines, transformers, and distributed circuits. State-of-the-art developments in Si based broadband analog, RF, microwave, and mm-wave circuits are reviewed. With up-to-date results, techniques, practical examples, illustrations and worked examples, this book will be valuable to advanced undergraduate and graduate students of electrical engineering, and practitioners in the IC design industry. Further resources for this title are available at www.cambridge.org/9780521853507.