Download or read book Control and Operation of Grid Connected Wind Farms written by John N. Jiang and published by Springer. This book was released on 2016-05-31 with total page 139 pages. Available in PDF, EPUB and Kindle. Book excerpt: From the point of view of grid integration and operation, this monograph advances the subject of wind energy control from the individual-unit to the wind-farm level. The basic objectives and requirements for successful integration of wind energy with existing power grids are discussed, followed by an overview of the state of the art, proposed solutions and challenges yet to be resolved. At the individual-turbine level, a nonlinear controller based on feedback linearization, uncertainty estimation and gradient-based optimization is shown robustly to control both active and reactive power outputs of variable-speed turbines with doubly-fed induction generators. Heuristic coordination of the output of a wind farm, represented by a single equivalent turbine with energy storage to optimize and smooth the active power output is presented. A generic approximate model of wind turbine control developed using system identification techniques is proposed to advance research and facilitate the treatment of control issues at the wind-farm level. A supervisory wind-farm controller is then introduced with a view to maximizing and regulating active power output under normal operating conditions and unusual contingencies. This helps to make the individual turbines cooperate in such as way that the overall output of the farm accurately tracks a reference and/or is statistically as smooth as possible to improve grid reliability. The text concludes with an overall discussion of the promise of advanced wind-farm control techniques in making wind an economic energy source and beneficial influence on grid performance. The challenges that warrant further research are succinctly enumerated. Control and Operation of Grid-Connected Wind Farms is primarily intended for researchers from a systems and control background wishing to apply their expertise to the area of wind-energy generation. At the same time, coverage of contemporary solutions to fundamental operational problems will benefit power/energy engineers endeavoring to promote wind as a reliable and clean source of electrical power.

Download or read book Control and Operation of Grid Connected Wind Energy Systems written by Ali M. Eltamaly and published by Springer Nature. This book was released on 2021-03-04 with total page 323 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edited book analyses and discusses the current issues of integration of wind energy systems in the power systems. It collects recent studies in the area, focusing on numerous issues including unbalanced grid voltages, low-voltage ride-through and voltage stability of the grid. It also explores the impact of the emerging technologies of wind turbines and power converters in the integration of wind power systems in power systems. This book utilizes the editors’ expertise in the energy sector to provide a comprehensive text that will be of interest to researchers, graduate students and industry professionals.

Download or read book Stability Augmentation of a Grid connected Wind Farm written by S. M. Muyeen and published by Springer Science & Business Media. This book was released on 2008-09-25 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: “Stability Augmentation of a Grid-connected Wind Farm” introduces a comprehensive approach to stabilizing the power output from wind farms, covering both fixed and variable speed wind turbine generator systems. The book presents the different tools suitable for application in wind farms, together with modeling and control strategies. The book reports on output power and terminal voltage fluctuation minimization, using the integration of energy storage systems with power electronic converters. Transient stability enhancement of the power systems is also discussed. “Stability Augmentation of a Grid-connected Wind Farm” provides advanced tools with detailed modeling and controller design, including extensive simulation results.

Download or read book Control and Operation of Grid Connected Wind Energy Systems written by Ali M. Eltamaly and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edited book analyses and discusses the current issues of integration of wind energy systems in the power systems. It collects recent studies in the area, focusing on numerous issues including unbalanced grid voltages, low-voltage ride-through and voltage stability of the grid. It also explores the impact of the emerging technologies of wind turbines and power converters in the integration of wind power systems in power systems. This book utilizes the editors' expertise in the energy sector to provide a comprehensive text that will be of interest to researchers, graduate students and industry professionals. .

Download or read book Large Grid Connected Wind Turbines written by Frede Blaabjerg and published by MDPI. This book was released on 2019-04-02 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the technological progress and developments of a large-scale wind energy conversion system along with its future trends, with each chapter constituting a contribution by a different leader in the wind energy arena. Recent developments in wind energy conversion systems, system optimization, stability augmentation, power smoothing, and many other fascinating topics are included in this book. Chapters are supported through modeling, control, and simulation analysis. This book contains both technical and review articles.

Download or read book Wind Energy Generation Modelling and Control written by Olimpo Anaya-Lara and published by John Wiley & Sons. This book was released on 2011-08-24 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: WIND ENERGY GENERATION WIND ENERGY GENERATION MODELLING AND CONTROL With increasing concern over climate change and the security of energy supplies, wind power is emerging as an important source of electrical energy throughout the world. Modern wind turbines use advanced power electronics to provide efficient generator control and to ensure compatible operation with the power system. Wind Energy Generation describes the fundamental principles and modelling of the electrical generator and power electronic systems used in large wind turbines. It also discusses how they interact with the power system and the influence of wind turbines on power system operation and stability. Key features: Includes a comprehensive account of power electronic equipment used in wind turbines and for their grid connection. Describes enabling technologies which facilitate the connection of large-scale onshore and offshore wind farms. Provides detailed modelling and control of wind turbine systems. Shows a number of simulations and case studies which explain the dynamic interaction between wind power and conventional generation.

Download or read book Operation and Control of Renewable Energy Systems written by Mukhtar Ahmad and published by John Wiley & Sons. This book was released on 2017-12-18 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference to renewable energy technologies with a focus on power generation and integration into power systems This book addresses the generation of energy (primarily electrical) through various renewable sources. It discusses solar and wind power—two major resources that are now in use in small as well as large-scale power production—and their requirements for effectively using advanced control techniques.In addition, the book looks at theintegration of renewable energy in the power grid and its ability to work in a micro grid. Operation and Control of Renewable Energy Systems describes the numerous types of renewable energy sources available and the basic principles involving energy conversion, including the theory of fluid mechanics and the laws of thermodynamics. Chapter coverage includes the theory of power electronics and various electric power generators, grid scale energy storage systems, photovoltaic power generation, solar thermal energy conversion technology, horizontal and vertical wind turbines for power generation, and more. Covers integration into power systems with an emphasis on microgrids Introduces a wide range of subjects related to renewable energy systems, including energy storage, microgrids, and battery technologies Includes tutorial materials such as up-to-date references for wind energy, grid connection, and power electronics—plus worked examples and solutions Operation and Control of Renewable Energy Systems is the perfect introduction to renewable energy technologies for undergraduate and graduate students and can also be very useful to practicing engineers.

Download or read book Offshore Wind Energy Generation written by Olimpo Anaya-Lara and published by John Wiley & Sons. This book was released on 2014-03-26 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: The offshore wind sector’s trend towards larger turbines, bigger wind farm projects and greater distance to shore has a critical impact on grid connection requirements for offshore wind power plants. This important reference sets out the fundamentals and latest innovations in electrical systems and control strategies deployed in offshore electricity grids for wind power integration. Includes: All current and emerging technologies for offshore wind integration and trends in energy storage systems, fault limiters, superconducting cables and gas-insulated transformers Protection of offshore wind farms illustrating numerous system integration and protection challenges through case studies Modelling of doubly-fed induction generators (DFIG) and full-converter wind turbines structures together with an explanation of the smart grid concept in the context of wind farms Comprehensive material on power electronic equipment employed in wind turbines with emphasis on enabling technologies (HVDC, STATCOM) to facilitate the connection and compensation of large-scale onshore and offshore wind farms Worked examples and case studies to help understand the dynamic interaction between HVDC links and offshore wind generation Concise description of the voltage source converter topologies, control and operation for offshore wind farm applications Companion website containing simulation models of the cases discussed throughout Equipping electrical engineers for the engineering challenges in utility-scale offshore wind farms, this is an essential resource for power system and connection code designers and pratitioners dealing with integation of wind generation and the modelling and control of wind turbines. It will also provide high-level support to academic researchers and advanced students in power and renewable energy as well as technical and research staff in transmission and distribution system operators and in wind turbine and electrical equipment manufacturers.

Download or read book Grid Integration of Wind Energy written by Siegfried Heier and published by John Wiley & Sons. This book was released on 2014-06-23 with total page 533 pages. Available in PDF, EPUB and Kindle. Book excerpt: This popular reference describes the integration of wind-generated power into electrical power systems and, with the use of advanced control systems, illustrates how wind farms can be made to operate like conventional power plants. Fully revised, the third edition provides up-to-date coverage on new generator developments for wind turbines, recent technical developments in electrical power conversion systems, control design and essential operating conditions. With expanded coverage of offshore technologies, this edition looks at the characteristics and static and dynamic behaviour of offshore wind farms and their connection to the mainland grid. Brand new material includes: comprehensive treatment of onshore and offshore grid integration updated legislative guidelines for the design, construction and installation of wind power plants the fundamental characteristics and theoretical tools of electrical and mechanical components and their interactions new and future types of generators, converters, power electronics and controller designs improved use of grid capacities and grid support for fixed- and variable-speed controlled wind power plants options for grid control and power reserve provision in wind power plants and wind farms This resource is an excellent guide for researchers and practitioners involved in the planning, installation and grid integration of wind turbines and power plants. It is also highly beneficial to university students studying wind power technology, renewable energy and power systems, and to practitioners in wind engineering, turbine design and manufacture and electrical power engineering.

Download or read book Enhanced Power Quality Management of Grid Connected Wind Farm written by Kadam Deepak Prakash and published by Independent Author. This book was released on 2023-04-14 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Windmills have been used for at least 3000 years, mainly for grinding grain or pumping water, while in sailing ships the wind has been an essential source of power for even longer. From as early as the thirteenth century, horizontal-axis windmills were an integral part of the rural economy and only fell into disuse with the advent of cheap fossil-fuelled engines and then the spread of rural electrification. To use wind energy efficiently and to concentrate the visual impact of modem wind turbines, the regions with a good wind climate, a tendency to group turbines in wind farms can be observed. These wind farms are connected to high voltage transmission grids and thus directly influence the dynamic behavior of the electrical power system [1]. Modern electricity-generating wind turbines now use three-bladed upwind rotors although two-bladed, and even one-bladed, rotors were used in earlier commercial turbines. Reducing the number of blades means that the rotor has to operate at a higher rotational speed in order to extract the wind energy from wind turbine. Initially these turbines were small, sometimes rated at only 30 kW, but were developed over the next 15 years to around 40-m diameter, 800-1,000 kW. However, by the mid-1990s it was becoming clear that for larger wind turbines it would be necessary to move away from this simple architecture and to use a number of the advanced concepts (e.g. variable-speed operation, pitch regulation, advanced materials) that had been investigated in the earlier research work. Large wind turbines are up to 100 m in diameter, rated at 3 to 4 MW are used. Most of the largest wind turbines now being installed operate at variable-speed, as the power electronic converters also allow much greater control of the output power and it is easier to comply with the requirements of the power system network operator.

Download or read book Modeling and Modern Control of Wind Power written by Qiuwei Wu and published by John Wiley & Sons. This book was released on 2018-02-05 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: An essential reference to the modeling techniques of wind turbine systems for the application of advanced control methods This book covers the modeling of wind power and application of modern control methods to the wind power control—specifically the models of type 3 and type 4 wind turbines. The modeling aspects will help readers to streamline the wind turbine and wind power plant modeling, and reduce the burden of power system simulations to investigate the impact of wind power on power systems. The use of modern control methods will help technology development, especially from the perspective of manufactures. Chapter coverage includes: status of wind power development, grid code requirements for wind power integration; modeling and control of doubly fed induction generator (DFIG) wind turbine generator (WTG); optimal control strategy for load reduction of full scale converter (FSC) WTG; clustering based WTG model linearization; adaptive control of wind turbines for maximum power point tracking (MPPT); distributed model predictive active power control of wind power plants and energy storage systems; model predictive voltage control of wind power plants; control of wind power plant clusters; and fault ride-through capability enhancement of VSC HVDC connected offshore wind power plants. Modeling and Modern Control of Wind Power also features tables, illustrations, case studies, and an appendix showing a selection of typical test systems and the code of adaptive and distributed model predictive control. Analyzes the developments in control methods for wind turbines (focusing on type 3 and type 4 wind turbines) Provides an overview of the latest changes in grid code requirements for wind power integration Reviews the operation characteristics of the FSC and DFIG WTG Presents production efficiency improvement of WTG under uncertainties and disturbances with adaptive control Deals with model predictive active and reactive power control of wind power plants Describes enhanced control of VSC HVDC connected offshore wind power plants Modeling and Modern Control of Wind Power is ideal for PhD students and researchers studying the field, but is also highly beneficial to engineers and transmission system operators (TSOs), wind turbine manufacturers, and consulting companies.

Download or read book Wind Power in Power Systems written by Thomas Ackermann and published by John Wiley & Sons. This book was released on 2012-04-23 with total page 1132 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine simulation models. This extensive update has 23 brand new chapters in cutting-edge areas including offshore wind farms and storage options, performance validation and certification for grid codes, and the provision of reactive power and voltage control from wind power plants. Key features: Offers an international perspective on integrating a high penetration of wind power into the power system, from basic network interconnection to industry deregulation; Outlines the methodology and results of European and North American large-scale grid integration studies; Extensive practical experience from wind power and power system experts and transmission systems operators in Germany, Denmark, Spain, UK, Ireland, USA, China and New Zealand; Presents various wind turbine designs from the electrical perspective and models for their simulation, and discusses industry standards and world-wide grid codes, along with power quality issues; Considers concepts to increase penetration of wind power in power systems, from wind turbine, power plant and power system redesign to smart grid and storage solutions. Carefully edited for a highly coherent structure, this work remains an essential reference for power system engineers, transmission and distribution network operator and planner, wind turbine designers, wind project developers and wind energy consultants dealing with the integration of wind power into the distribution or transmission network. Up-to-date and comprehensive, it is also useful for graduate students, researchers, regulation authorities, and policy makers who work in the area of wind power and need to understand the relevant power system integration issues.

Download or read book Stability Control and Reliable Performance of Wind Turbines written by Kenneth Eloghene Okedu and published by BoD – Books on Demand. This book was released on 2018-10-10 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended for academics and engineers working in universities, research institutes, and industry sectors wishing to acquire new information and enhance their knowledge of the current trends in wind turbine technology. Readers will gain new ideas and special experience with in-depth information about modeling, stability control, assessment, reliability, and future prospects of wind turbines. This book contains a number of problems and solutions that can be integrated into larger research findings and projects. The book enhances studies concerning the state of the art of wind turbines, modeling and intelligent control of wind turbines, power quality of wind turbines, robust controllers for wind turbines in cold weather, etc. The book also looks at recent developments in wind turbine supporting structures, noise reduction estimation methods, reliability and prospects of wind turbines, etc. As I enjoyed preparing this book, I am sure that it will be valuable for a large sector of readers.

Download or read book Offshore Wind Energy Technology written by Olimpo Anaya-Lara and published by John Wiley & Sons. This book was released on 2018-05-11 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt: A COMPREHENSIVE REFERENCE TO THE MOST RECENT ADVANCEMENTS IN OFFSHORE WIND TECHNOLOGY Offshore Wind Energy Technology offers a reference based on the research material developed by the acclaimed Norwegian Research Centre for Offshore Wind Technology (NOWITECH) and material developed by the expert authors over the last 20 years. This comprehensive text covers critical topics such as wind energy conversion systems technology, control systems, grid connection and system integration, and novel structures including bottom-fixed and floating. The text also reviews the most current operation and maintenance strategies as well as technologies and design tools for novel offshore wind energy concepts. The text contains a wealth of mathematical derivations, tables, graphs, worked examples, and illustrative case studies. Authoritative and accessible, Offshore Wind Energy Technology: Contains coverage of electricity markets for offshore wind energy and then discusses the challenges posed by the cost and limited opportunities Discusses novel offshore wind turbine structures and floaters Features an analysis of the stochastic dynamics of offshore/marine structures Describes the logistics of planning, designing, building, and connecting an offshore wind farm Written for students and professionals in the field, Offshore Wind Energy Technology is a definitive resource that reviews all facets of offshore wind energy technology and grid connection.

Download or read book Understanding Wind Power Technology written by Alois Schaffarczyk and published by John Wiley & Sons. This book was released on 2014-04-10 with total page 688 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wind energy technology has progressed enormously over the last decade. In coming years it will continue to develop in terms of power ratings, performance and installed capacity of large wind turbines worldwide, with exciting developments in offshore installations. Designed to meet the training needs of wind engineers, this introductory text puts wind energy in context, from the natural resource to the assessment of cost effectiveness and bridges the gap between theory and practice. The thorough coverage spans the scientific basics, practical implementations and the modern state of technology used in onshore and offshore wind farms for electricity generation. Key features: provides in-depth treatment of all systems associated with wind energy, including the aerodynamic and structural aspects of blade design, the flow of energy and loads through the wind turbine, the electrical components and power electronics including control systems explains the importance of wind resource assessment techniques, site evaluation and ecology with a focus of project planning and operation describes the integration of wind farms into the electric grid and includes a whole chapter dedicated to offshore wind farms includes questions in each chapter for readers to test their knowledge Written by experts with deep experience in research, teaching and industry, this text conveys the importance of wind energy in the international energy-policy debate, and offers clear insight into the subject for postgraduates and final year undergraduate students studying all aspects of wind engineering. Understanding Wind Power Systems is also an authoritative resource for engineers designing and developing wind energy systems, energy policy makers, environmentalists, and economists in the renewable energy sector.

Download or read book Wind and Solar Power Systems written by Mukund R. Patel and published by CRC Press. This book was released on 1999-03-30 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wind and solar energy are pollution-free sources of abundant power. With renewable power generation expected to become more and more profitable with open access to transmission lines and rapid growth around the world, the design, operation, and control of alternative energy resources becomes an essential field of study. Wind and Solar Power Systems provides a comprehensive treatment of this rapidly growing segment of the power industry. It provides the fundamentals of wind and solar power generation, energy conversion and storage, and the operational aspects of power electronics and the quality of power. It covers in detail the design, operation, and control methods applicable to stand-alone as well as grid-connected power systems and discusses the present status of and the on-going research in renewable power around the world. Wind and Solar Power Systems stands as the most modern, complete book available on renewable energy. Electrical, environmental and mechanical engineering professionals along with policy-makers evaluating the renewable energy potential of their regions will find in it the background and the details they need for decision making.

Download or read book Source Grid Interaction of Wind Power Integration Systems written by Da Xie and published by Elsevier. This book was released on 2023-04-29 with total page 620 pages. Available in PDF, EPUB and Kindle. Book excerpt: Source-Grid Interaction of Wind Power Integration Systems systematically describes the problems of source-grid interactions of wind power grid-connected system, introducing related research methods and proposing a series of novel control methods for damping oscillations. The book presents problems to be solved, thus enabling easy understanding and perception, from detailed analysis of the problems, to mathematical derivations and simulation verification. Includes principles that can be used to analyze the operation and control of wind farms Presents models developed from basic to complex aspects that affect modeling accuracy Provides control methods and effectiveness verification based on rigorous theory and actual operational data