Download or read book Computer Simulation Of Spark Ignition Engine Processes written by V. Ganesan and published by Universities Press. This book was released on 1996 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the theory and computer programs for the simulation of spark ignition (SI) engine processes. It starts with the fundamental concepts and goes on to the advanced level and can thus be used by undergraduates, postgraduates and Ph. D. scholars.
Download or read book Computer Simulation Of Compression Ignition Engine Processes written by V. Ganesan and published by Universities Press. This book was released on with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book attempts to provide a simplified framework for the vast and complex map of technical material that exists on compression-ignition engines, and at the same time include sufficient details to convey the complexity of engine simulation. The emphasis here is on the thermodynamics, combustion physics and chemistry, heat transfer, and friction processes relevant to compression-ignition engines with simplifying assumpations.
Download or read book Quasi Dimensional Simulation of Spark Ignition Engines written by Alejandro Medina and published by Springer Science & Business Media. This book was released on 2013-08-20 with total page 201 pages. Available in PDF, EPUB and Kindle. Book excerpt: Based on the simulations developed in research groups over the past years, Introduction to Quasi-dimensional Simulation of Spark Ignition Engines provides a compilation of the main ingredients necessary to build up a quasi-dimensional computer simulation scheme. Quasi-dimensional computer simulation of spark ignition engines is a powerful but affordable tool which obtains realistic estimations of a wide variety of variables for a simulated engine keeping insight the basic physical and chemical processes involved in the real evolution of an automotive engine. With low computational costs, it can optimize the design and operation of spark ignition engines as well as it allows to analyze cycle-to-cycle fluctuations. Including details about the structure of a complete simulation scheme, information about what kind of information can be obtained, and comparisons of the simulation results with experiments, Introduction to Quasi-dimensional Simulation of Spark Ignition Engines offers a thorough guide of this technique. Advanced undergraduates and postgraduates as well as researchers in government and industry in all areas related to applied physics and mechanical and automotive engineering can apply these tools to simulate cyclic variability, potentially leading to new design and control alternatives for lowering emissions and expanding the actual operation limits of spark ignition engines
Download or read book Internal Combustion Engine Fundamentals written by John B. Heywood and published by McGraw-Hill Education. This book was released on 1988 with total page 930 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text, by a leading authority in the field, presents a fundamental and factual development of the science and engineering underlying the design of combustion engines and turbines. An extensive illustration program supports the concepts and theories discussed.
Download or read book Introduction to Modeling and Control of Internal Combustion Engine Systems written by Lino Guzzella and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 303 pages. Available in PDF, EPUB and Kindle. Book excerpt: Internal combustion engines still have a potential for substantial improvements, particularly with regard to fuel efficiency and environmental compatibility. These goals can be achieved with help of control systems. Modeling and Control of Internal Combustion Engines (ICE) addresses these issues by offering an introduction to cost-effective model-based control system design for ICE. The primary emphasis is put on the ICE and its auxiliary devices. Mathematical models for these processes are developed in the text and selected feedforward and feedback control problems are discussed. The appendix contains a summary of the most important controller analysis and design methods, and a case study that analyzes a simplified idle-speed control problem. The book is written for students interested in the design of classical and novel ICE control systems.
Download or read book Assessment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2011-06-03 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various combinations of commercially available technologies could greatly reduce fuel consumption in passenger cars, sport-utility vehicles, minivans, and other light-duty vehicles without compromising vehicle performance or safety. Assessment of Technologies for Improving Light Duty Vehicle Fuel Economy estimates the potential fuel savings and costs to consumers of available technology combinations for three types of engines: spark-ignition gasoline, compression-ignition diesel, and hybrid. According to its estimates, adopting the full combination of improved technologies in medium and large cars and pickup trucks with spark-ignition engines could reduce fuel consumption by 29 percent at an additional cost of $2,200 to the consumer. Replacing spark-ignition engines with diesel engines and components would yield fuel savings of about 37 percent at an added cost of approximately $5,900 per vehicle, and replacing spark-ignition engines with hybrid engines and components would reduce fuel consumption by 43 percent at an increase of $6,000 per vehicle. The book focuses on fuel consumption-the amount of fuel consumed in a given driving distance-because energy savings are directly related to the amount of fuel used. In contrast, fuel economy measures how far a vehicle will travel with a gallon of fuel. Because fuel consumption data indicate money saved on fuel purchases and reductions in carbon dioxide emissions, the book finds that vehicle stickers should provide consumers with fuel consumption data in addition to fuel economy information.
Download or read book Thermal System Design and Simulation written by P.L. Dhar and published by Academic Press. This book was released on 2016-10-25 with total page 618 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal System Design and Simulation covers the fundamental analyses of thermal energy systems that enable users to effectively formulate their own simulation and optimal design procedures. This reference provides thorough guidance on how to formulate optimal design constraints and develop strategies to solve them with minimal computational effort. The book uniquely illustrates the methodology of combining information flow diagrams to simplify system simulation procedures needed in optimal design. It also includes a comprehensive presentation on dynamics of thermal systems and the control systems needed to ensure safe operation at varying loads. Designed to give readers the skills to develop their own customized software for simulating and designing thermal systems, this book is relevant for anyone interested in obtaining an advanced knowledge of thermal system analysis and design. - Contains detailed models of simulation for equipment in the most commonly used thermal engineering systems - Features illustrations for the methodology of using information flow diagrams to simplify system simulation procedures - Includes comprehensive global case studies of simulation and optimization of thermal systems
Download or read book Fuel Economy written by John C. Hilliard and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concern about the reduced availability and the increased cost of petroleum fuels prompted great efforts in recent years to reduce the fuel consumption of auto mobiles. The ongoing efforts to reduce fuel consumption have addressed many relevant factors, including increased engine performance, reduced friction, use of lightweight materials, and reduced aerodynamic drag. The results of the investigations assessing the various factors affecting fuel economy have been published in journals, conference proceedings, and in company and government reports. This proliferation of technical information makes it difficult for workers to keep abreast of aU developments. The material presented in this book brings together in a single volume much of the relevant materials, summarizes many of the state-of-the-art theories and data, and provides extensive lists of references. Thus, it is hoped that this book will be a useful reference for specialists and practicing engineers interested in the fuel economy of automobiles. J. C. HILLIARD o. S. SPRINGER vii CONTENTS 1. AUTOMOTIVE FUEL ECONOMY David Cole I. Introduction and Background. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . n. Fuel Economy Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 A. Engine................................................... 11 B. Drive Train. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 . . . . . . . . . . . . . . C. Vehicle Factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . D. Operating Factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 . . . . . . . . . . . . E. Test Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 . . . . . . . . . . . . . . . . . 2. FUEL ECONOMY AND EMISSIONS J. T. Kummer I. Introduction .................................................. . 35 n. Emission Regulations .......................................... .
Download or read book Diesel Engine Transient Operation written by Constantine D. Rakopoulos and published by Springer Science & Business Media. This book was released on 2009-03-10 with total page 408 pages. Available in PDF, EPUB and Kindle. Book excerpt: Traditionally, the study of internal combustion engines operation has focused on the steady-state performance. However, the daily driving schedule of automotive and truck engines is inherently related to unsteady conditions. In fact, only a very small portion of a vehicle’s operating pattern is true steady-state, e. g. , when cruising on a motorway. Moreover, the most critical conditions encountered by industrial or marine engines are met during transients too. Unfortunately, the transient operation of turbocharged diesel engines has been associated with slow acceleration rate, hence poor driveability, and overshoot in particulate, gaseous and noise emissions. Despite the relatively large number of published papers, this very important subject has been treated in the past scarcely and only segmentally as regards reference books. Merely two chapters, one in the book Turbocharging the Internal Combustion Engine by N. Watson and M. S. Janota (McMillan Press, 1982) and another one written by D. E. Winterbone in the book The Thermodynamics and Gas Dynamics of Internal Combustion Engines, Vol. II edited by J. H. Horlock and D. E. Winterbone (Clarendon Press, 1986) are dedicated to transient operation. Both books, now out of print, were published a long time ago. Then, it seems reasonable to try to expand on these pioneering works, taking into account the recent technological advances and particularly the global concern about environmental pollution, which has intensified the research on transient (diesel) engine operation, typically through the Transient Cycles certification of new vehicles.
Download or read book Combustion for Power Generation and Transportation written by Avinash Kumar Agarwal and published by Springer. This book was released on 2017-01-20 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph presents both fundamental science and applied innovations on several key and emerging technologies involving fossil and alternate fuel utilization in power and transport sectors from renowned experts in the field. Some of the topics covered include: autoignition in laminar and turbulent nonpremixed flames; Langevin simulation of turbulent combustion; lean blowout (LBO) prediction through symbolic time series analysis; lasers and optical diagnostics for next generation IC engine development; exergy destruction study on small DI diesel engine; and gasoline direct injection. The book includes a chapter on carbon sequestration and optimization of enhanced oil and gas recovery. The contents of this book will be useful to researchers and professionals working on all aspects on combustion.
Download or read book Engine Modeling and Control written by Rolf Isermann and published by Springer. This book was released on 2016-09-24 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The increasing demands for internal combustion engines with regard to fuel consumption, emissions and driveability lead to more actuators, sensors and complex control functions. A systematic implementation of the electronic control systems requires mathematical models from basic design through simulation to calibration. The book treats physically-based as well as models based experimentally on test benches for gasoline (spark ignition) and diesel (compression ignition) engines and uses them for the design of the different control functions. The main topics are: - Development steps for engine control - Stationary and dynamic experimental modeling - Physical models of intake, combustion, mechanical system, turbocharger, exhaust, cooling, lubrication, drive train - Engine control structures, hardware, software, actuators, sensors, fuel supply, injection system, camshaft - Engine control methods, static and dynamic feedforward and feedback control, calibration and optimization, HiL, RCP, control software development - Control of gasoline engines, control of air/fuel, ignition, knock, idle, coolant, adaptive control functions - Control of diesel engines, combustion models, air flow and exhaust recirculation control, combustion-pressure-based control (HCCI), optimization of feedforward and feedback control, smoke limitation and emission control This book is an introduction to electronic engine management with many practical examples, measurements and research results. It is aimed at advanced students of electrical, mechanical, mechatronic and control engineering and at practicing engineers in the field of combustion engine and automotive engineering.
Download or read book Recent Advancements in Mechanical Engineering written by T. S. Sudarshan and published by Springer Nature. This book was released on with total page 474 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Combustion Engines Development written by Günter P. Merker and published by Springer Science & Business Media. This book was released on 2011-09-24 with total page 660 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion Engines Development nowadays is based on simulation, not only of the transient reaction of vehicles or of the complete driveshaft, but also of the highly unsteady processes in the carburation process and the combustion chamber of an engine. Different physical and chemical approaches are described to show the potentials and limits of the models used for simulation.
Download or read book Internal Combustion Engines written by Colin R. Ferguson and published by John Wiley & Sons. This book was released on 2015-07-01 with total page 477 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the publication of the Second Edition in 2001, there have been considerable advances and developments in the field of internal combustion engines. These include the increased importance of biofuels, new internal combustion processes, more stringent emissions requirements and characterization, and more detailed engine performance modeling, instrumentation, and control. There have also been changes in the instructional methodologies used in the applied thermal sciences that require inclusion in a new edition. These methodologies suggest that an increased focus on applications, examples, problem-based learning, and computation will have a positive effect on learning of the material, both at the novice student, and practicing engineer level. This Third Edition mirrors its predecessor with additional tables, illustrations, photographs, examples, and problems/solutions. All of the software is ‘open source’, so that readers can see how the computations are performed. In addition to additional java applets, there is companion Matlab code, which has become a default computational tool in most mechanical engineering programs.
Download or read book Numerical Simulation Advanced Techniques for Science and Engineering written by Ali Soofastaei and published by BoD – Books on Demand. This book was released on 2023-11-15 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical simulation is a powerful tool used in various fields of science and engineering to model complex systems and predict their behavior. It involves developing mathematical models that describe the behavior of a system and using computer algorithms to solve these models numerically. By doing so, researchers and engineers can study the behavior of a system in detail, which may only be possible with analytical methods. Numerical simulation has many advantages over traditional analytical methods. It allows researchers and engineers to study complex systems’ behavior in detail and predict their behavior in different scenarios. It also allows for the optimization of systems and the identification of design flaws before they are built. However, numerical simulation has its limitations. It requires significant computational resources, and the accuracy of the results depends on the quality of the mathematical models and the discretization methods used. Nevertheless, numerical simulation remains a valuable tool in many fields and its importance is likely to grow as computational resources become more powerful and widely available. Numerical simulation is widely used in physics, engineering, computer science, and mathematics. In physics, for example, numerical simulation is used to study the behavior of complex systems such as weather patterns, fluid dynamics, and particle interactions. In engineering, it is used to design and optimize systems such as aircraft, cars, and buildings. In computer science, numerical simulation models and optimization algorithms and data structures. In mathematics, it is used to study complex mathematical models and to solve complex equations. This book familiarizes readers with the practical application of the numerical simulation technique to solve complex analytical problems in different industries and sciences.
Download or read book Differential Equations written by Balachandra Rao S. and published by Universities Press. This book was released on 1998-09 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is designed as a textbook for undergraduate students of mathematics, physics, physical chemistry, engineering, etc. It also contains a large number of worked exaples besides exercises and answers. A whole chapte is devoted to numerical techniques to solve differential equations in which computer programs and printouts of worked examples are inclued.
Download or read book Fundamentals of Fuel Injection and Emission in Two Stroke Engines written by Wadysaw Mitianiec and published by Nova Science Publishers. This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main goal of the book is the presentation of the last theoretical and experimental works concerning fuel injection systems, mainly in small power two-stroke engines as well as in marine engines. This book includes thirteen chapters devoted to the processes of fuel injection and the combustion that takes place in a stratified charge within the cylinders of two-stroke engines. In the first two chapters, the division into different injection systems in two-stroke engines and each injection system is briefly described. Various theoretical and practical solutions of fueling system designs are described. In Chapter Three, mathematical models, the spatial movement of gas in the cylinder and the combustion chamber are introduced, taking into account the turbulence of the charge. Chapter Four relates to the behavior of fuel injected into the gaseous medium, including evaporation processes, disintegration and processes occurring while the fuel drops connect with the wall. The next section describes the zero-dimensional model of fuel injection in two-stroke engines along with examples of numerical calculations. The sixth chapter is devoted to CFD multi-dimensional models of movement and evaporation of the fuel in a closed gaseous medium, occurring also in other engine types. Chapter Seven describes a two-zone model of the combustion process and the effect of the geometry of the combustion chamber on the flame propagation with a simplified verification model of combustion. Chapter Eight compares the propagation phase of gas and liquid fuels concerning direct fuel injection as well as the direct fuel injection from the cylinder head and the thermodynamic parameters of the charge. The formation of the components during the combustion process in the direct fuel injection two-stroke engine was obtained by numerical calculations and results are discussed in Chapter Nine. Chapter Ten describes the parameters of the two-stroke engine with a direct fuel injection carried out at the Cracow University of Technology. Additionally, the chapter presents CFD simulations of fuel propagation and combustion processes, taking into account the formation of toxic components and exhaust gas emission. The processes of two direct rich mixture injection systems FAST and RMIS developed in CUT are presented in Chapter Eleven. Miscellaneous problems of direct fuel injection, such as characteristics of fuel injectors, problems of direct gaseous fuel injection, and the application of fuelling systems in outboard engines and snowmobile vehicles are presented in Chapter Twelve. A comparison of working parameters in two- and four stroke engines is also mapped out. The last chapters contain the final conclusions and remarks concerning fuel injection and emission of exhaust gases in small two-stroke engines. This book is a comprehensive monograph on fuel injection. The author presents a series of theoretical and design information from his own experience and on the basis of the works of other authors. The main text intends to direct fuel injection with respect to gas motion in the combustion chamber and influence the injection parameters for exhaust emission. The book presents its own theoretical work and experimental tests concerning a two-stroke gasoline engine with electrically controlled direct fuel injection. The book describes the processes of a general nature also occurring in other types of engines and presents a comparison of different injection systems on working parameters and gas emission. The book contains 294 images, 290 equations and 16 tables obtained from the CFD simulation and experimental works.
