Download or read book Computer Methods and Experimental Measurements for Surface Effects and Contact Mechanics VIII written by J. T. M. de Hosson and published by WIT Press. This book was released on 2007 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of contact and surface problems in modern engineering and their combined effects has led to the Eighth International Conference on Computer Methods and Experimental Measurements for Surface and Contact Mechanics. Nowadays the importance of contact and surface problems in many technological fields is well understood: they are complex and inherently non-linear due to their moving boundaries and the different properties of materials, particularly along the contact surfaces. Structural components fail from wear, corrosion, high cycle fatigue etc., that is to say affected and initiated by the surface conditions. The use of surface treatments can reduce the cost of components and extend the life of the elements. Their effect is of particular importance in the case of surfaces undergoing contact, a problem which is addressed throughout the book. Topics featured: Surface Treatment; Surface problems in Contact Mechanics; Fracture Mechanics; Coupled analysis and experiments; Thin Coatings; Thick Coatings; Contact Mechanics; Material Surface in Contact; Applications and Case Studies.
Download or read book Computer Methods and Experimental Measurements for Surface Treatment Effects II written by M. H. Aliabadi and published by Computational Mechanics. This book was released on 1995-01-01 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: These conference proceedings cover surface treatments, which are receiving increased attention by the engineering community in order to reduce the cost of expensive components used in critical applications, as well as extending the useful lifetime of existing structural components, or increasing the load capacity for the same life.
Download or read book Computer Methods and Experimental Measurements for Surface Effects and Contact Mechanics VII written by J. T. M. de Hosson and published by Computational Mechanics. This book was released on 2005 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: The research activities in the field of surface engineering have been greatly driven by the realization that the surface is usually the most important part of any engineering component. The scientific research featured deals with fundamental and applied concepts of surface engineering, in particular focusing on the interplay between applied physics, materials science and engineering, computational mechanics and mechanical engineering. The book is devoted to fundamental and applied studies of four interconnected aspects: processing, microstructural features, functional performance as well as the design of an appropriate theoretical and predictive framework of protective surfaces.
Download or read book Electroless Nickel Plating Fundamentals to Applications written by Fabienne Delaunois and published by CRC Press. This book was released on 2019-10-30 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electroless Nickel Plating: Fundamentals to Applications provides a complete and actualized view of electroless nickel plating, thus greatly improving the accessibility of knowledge on the subject. It touches upon all aspects of electroless nickel, from the fundamentals (including thermodynamics of electroless plating, bath chemistry, and substrate preparation) to more applied areas of the field such as bath replenishment, composite coatings, post-treatments, polyalloys, graded and multilayer coatings, ultrasound assistance, applications, and properties. Contributed to by a variety of international authors to ensure different points of view and interests are addressed, this book stands as the first complete and updated state-of-the-art text on electroless nickel in the twenty-first century. It also serves as the first technical book with a strong emphasis on nickel-boron. It also focuses on environmental aspects. Including cutting-edge content presented sufficiently extensive to be directly useful to the practitioner, this book is aimed at materials scientists, metallurgists, and other professionals working with electroless nickel plating.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1979 with total page 840 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Abrasive Technology Current Development And Applications I Proceedings Of The Third International Conference On Abrasive Technology Abtec 99 written by William J Scott and published by World Scientific. This book was released on 1999-11-10 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Abrasive technology is becoming increasingly important in precision manufacturing. This volume contains more than 70 refereed technical papers contributed by worldwide academic researchers and industrial practitioners, on the latest development in abrasive technology. Specifically, it covers the mechanics and mechanisms of abrasive processes as well as the technologies and applications related to abrasive jet machining, nano-machining, grinding, polishing, horning and lapping. It also includes topics on high-speed machining, eco-machining and laser micro-machining technologies. The discussion on the practical applications of abrasive technology and the associated theories makes this book useful for academic researchers and industrial practitioners.
Download or read book Small Fatigue Cracks written by K.S. Ravichandran and published by Elsevier. This book was released on 1999-09-30 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the fully peer-reviewed papers presented at the Third Engineering Foundation Conference on Small Fatigue Cracks, held under the chairmanship of K.S. Ravichandran and Y. Murakami during December 6-11, 1998, at the Turtle Bay Hilton, Oahu, Hawaii. This book presents a state-of-the-art description of the mechanics, mechanisms and applications of small fatigue cracks by most of the world's leading experts in this field. Topics ranging from the mechanisms of crack initiation, small crack behavior in metallic, intermetallic, ceramic and composite materials, experimental measurement, mechanistic and theoretical models, to the role of small cracks in fretting fatigue and the application of small crack results to the aging aircraft and high-cycle fatigue problems, are covered.
Download or read book Joints in Aluminium INALCO 98 written by M H Ogle and published by Woodhead Publishing. This book was released on 1999-09-30 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: The proceedings of the 7th INALCO conference which was held at TWI, Cambridge in April 1998.
Download or read book Applied Mechanics written by L. C. Zhang and published by World Scientific. This book was released on 2002 with total page 738 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the proceedings of the Third Australasian Congress on Applied Mechanics (ACAM2002). The Congress was held to provide an international forum for researchers, industry practitioners, engineers and postgraduate scholars to exchange and disseminate knowledge and experience of the most recent advances with a focus on the behaviour of solids. Topics include: biomechanics; constitutive modelling; damage; fracture; fatigue; dynamics; impact; vibration; geo-mechanics; tribology; machining and more.
Download or read book Modern Mechanical Surface Treatment written by Volker Schulze and published by John Wiley & Sons. This book was released on 2006-05-12 with total page 375 pages. Available in PDF, EPUB and Kindle. Book excerpt: The only comprehensive, systematic comparison of major mechanical surface treatments, their effects, and the resulting material properties. The result is an up-to-date, full review of this topic, collating the knowledge hitherto spread throughout many original papers. The book begins with a description of elementary processes and mechanisms to give readers an easy introduction, before proceeding to offer systematic, detailed descriptions of the various techniques and three very important types of loading: thermal, quasistatic, and cyclic loading. It combines and correlates experimental and model aspects, while supplying in-depth explanations of the mechanisms and a very high amount of exemplary data.
Download or read book The Cumulative Book Index written by and published by . This book was released on 1998 with total page 2348 pages. Available in PDF, EPUB and Kindle. Book excerpt: A world list of books in the English language.
Download or read book THERMEC 2003 written by T. Candra and published by Trans Tech Publications Ltd. This book was released on 2003-08-15 with total page 4690 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the International Conference on Processing & Manufacturing of Advanced Materials
Download or read book International Journal of Materials Product Technology written by and published by . This book was released on 2000 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanostructured Coatings written by Albano Cavaleiro and published by Springer Science & Business Media. This book was released on 2007-02-19 with total page 671 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book delivers practical insight into a broad range of fields related to hard coatings, from their deposition and characterization up to the hardening and deformation mechanisms allowing the interpretation of results. The text examines relationships between structure/microstructure and mechanical properties from fundamental concepts, through types of coatings, to characterization techniques. The authors explore the search for coatings that can satisfy the criteria for successful implementation in real mechanical applications.
Download or read book Tribologie Pour Les Syst mes A rospatiaux written by North Atlantic Treaty Organization. Advisory Group for Aerospace Research and Development. Structures and Materials Panel. Meeting and published by . This book was released on 1996 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Computational Methods and Experiments in Materials Characterization III written by C. A. Brebbia and published by WIT Press. This book was released on 2007 with total page 465 pages. Available in PDF, EPUB and Kindle. Book excerpt: Until recently, engineering materials could be characterized successfully using relatively simple testing procedures. As materials technology advances, interest is growing in materials possessing complex meso-, micro- and nano-structures, which to a large extent determine their physical properties and behaviour. The purposes of materials modelling are many: optimization, investigation of failure, simulation of production processes, to name but a few. Modelling and characterisation are closely intertwined, increasingly so as the complexity of the material increases. Characterisation, in essence, is the connection between the abstract material model and the real-world behaviour of the material in question. Characterisation of complex materials therefore may require a combination of experimental techniques and computation. This book publishes papers presented at the Third International Conference on Computational Methods and Experiments in Material Characterisation.Topics covered include: Composites; Ceramics; Alloys; Cements and Cement Based Materials; Biomaterials; Thin Films and Coatings; Advanced Materials; Imaging Analysis; Thermal Analysis; New Methods; Surface Chemistry, Nano Indentation; Continuum Methods; Particle Models; Damage Mechanics; Innovative Techniques; Stochastic Methods.
Download or read book Simulation of Electrochemical Processes II written by V.G. DeGiorgi and published by WIT Press. This book was released on 2007-04-10 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains papers presented at the Second International Conference in this successful series, which presents and discusses the state-of-the-art on the computer simulation of corrosion, electrochemical processes and the electrical and electromagnetic fields associated with them.Modern industry applies a wide range of electrochemical processes to protect against corrosion, provide surface treatments and to manufacture products. This book focuses on the computer modelling of these industrial processes and techniques by examining the developments of computational models and their application in practice.Featured topics include: Cathodic Protection Systems; Modelling Methodologies; Electrodeposition and Electroforming; Modelling of Coatings; Modelling Stress Corrosion, Cracking and Corrosion Fatigue; Modelling and Corrosion of Surface Coatings; Interference and Signature Control; Anodic Protection; Electrocoating and Plating; Optimisation of Control Systems; Detection and Monitoring of Corrosion; Measurement Techniques; Fuel on Photovoltaic Cells; Electrolysis Reactors; Comparison of Experimental Measurements and Computer results, Case Studies.
