Download or read book Computation of the Steady state Solution of Nonlinear Circuits with Time domain and Large signal small signal Analysis Methods written by Hannu Jokinen and published by . This book was released on 1997 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book New Topics in Simulation and Modeling of RF Circuits written by Alexandru Gabriel Gheorghe and published by CRC Press. This book was released on 2022-09-01 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: New Topics in Simulation and Modeling of RF Circuits addresses two main topics: simulation of RF circuits and new models of nonlinear power BAW resonators and filters.Since RF circuits have several unique features, and all analysis methods are based on the circuit essential properties, the book begins by describing the properties of RF circuits, characterization of circuits with customary and uncustomary behavior and some theorems of solutions existence and uniqueness for dynamic nonlinear circuits. Thereafter, the main time domain and frequency domain analysis methods for RF circuits are presented. The advantages and disadvantages of each method have been highlighted, and an algorithm for the time step choice in transient analysis based on energy balance errors is also presented. Lastly, the final part contains some nonlinear circuit models of power BAW resonators. The behavioral models for the time domain analysis are simple circuits containing weakly nonlinear elements. The behavioral models for frequency domain analysis are based on the measured values of the frequency dependent S parameters for a set of incident powers. S parameters corresponding to certain intermodulation products of practical interest are also considered. The physical models contain artificial transmission lines with nonlinear circuit elements corresponding to mechanical and electrical nonlinearities.
Download or read book Analysis and Simulation of Noise in Nonlinear Electronic Circuits and Systems written by Alper Demir and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: In electronic circuit and system design, the word noise is used to refer to any undesired excitation on the system. In other contexts, noise is also used to refer to signals or excitations which exhibit chaotic or random behavior. The source of noise can be either internal or external to the system. For instance, the thermal and shot noise generated within integrated circuit devices are in ternal noise sources, and the noise picked up from the environment through electromagnetic interference is an external one. Electromagnetic interference can also occur between different components of the same system. In integrated circuits (Ies), signals in one part of the system can propagate to the other parts of the same system through electromagnetic coupling, power supply lines and the Ie substrate. For instance, in a mixed-signal Ie, the switching activity in the digital parts of the circuit can adversely affect the performance of the analog section of the circuit by traveling through the power supply lines and the substrate. Prediction of the effect of these noise sources on the performance of an electronic system is called noise analysis or noise simulation. A methodology for the noise analysis or simulation of an electronic system usually has the following four components: 2 NOISE IN NONLINEAR ELECTRONIC CIRCUITS • Mathematical representations or models for the noise sources. • Mathematical model or representation for the system that is under the in fluence of the noise sources.
Download or read book The Best of ICCAD written by Andreas Kuehlmann and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 699 pages. Available in PDF, EPUB and Kindle. Book excerpt: In 2002, the International Conference on Computer Aided Design (ICCAD) celebrates its 20th anniversary. This book commemorates contributions made by ICCAD to the broad field of design automation during that time. The foundation of ICCAD in 1982 coincided with the growth of Large Scale Integration. The sharply increased functionality of board-level circuits led to a major demand for more powerful Electronic Design Automation (EDA) tools. At the same time, LSI grew quickly and advanced circuit integration became widely avail able. This, in turn, required new tools, using sophisticated modeling, analysis and optimization algorithms in order to manage the evermore complex design processes. Not surprisingly, during the same period, a number of start-up com panies began to commercialize EDA solutions, complementing various existing in-house efforts. The overall increased interest in Design Automation (DA) re quired a new forum for the emerging community of EDA professionals; one which would be focused on the publication of high-quality research results and provide a structure for the exchange of ideas on a broad scale. Many of the original ICCAD volunteers were also members of CANDE (Computer-Aided Network Design), a workshop of the IEEE Circuits and Sys tem Society. In fact, it was at a CANDE workshop that Bill McCalla suggested the creation of a conference for the EDA professional. (Bill later developed the name).
Download or read book III V Microelectronics written by J.P. Nougier and published by Elsevier. This book was released on 2014-05-27 with total page 523 pages. Available in PDF, EPUB and Kindle. Book excerpt: As is well known, Silicon widely dominates the market of semiconductor devices and circuits, and in particular is well suited for Ultra Large Scale Integration processes. However, a number of III-V compound semiconductor devices and circuits have recently been built, and the contributions in this volume are devoted to those types of materials, which offer a number of interesting properties. Taking into account the great variety of problems encountered and of their mutual correlations when fabricating a circuit or even a device, most of the aspects of III-V microelectronics, from fundamental physics to modelling and technology, from materials to devices and circuits are reviewed. Containing contributions from European researchers of international repute this volume is the definitive reference source for anyone interested in the latest advances and results of current experimental research in III-V microelectronics.
Download or read book Nonlinear Microwave Circuit Design written by Franco Giannini and published by John Wiley & Sons. This book was released on 2004-10-22 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design techniques for nonlinear microwave circuits are much less developed than for linear microwave circuits. Until now there has been no up-to-date text available in this area. Current titles in this field are considered outdated and tend to focus on analysis, failing to adequately address design and measurement aspects. Giannini and Leuzzi provide the theoretical background to non-linear microwave circuits before going on to discuss the practical design and measurement of non-linear circuits and components. Non-linear Microwave Circuit Design reviews all of the established analysis and characterisation techniques available and provides detailed coverage of key modelling methods. Practical examples are used throughout the text to emphasise the design and application focus of the book. Provides a unique, design-focused, coverage of non-linear microwave circuits Covers the fundamental properties of nonlinear circuits and methods for device modelling Outlines non-linear measurement techniques and characterisation of active devices Reviews available design methodologies for non-linear power amplifiers and details advanced software modelling tools Provides the first detailed treatment of non-linear frequency multipliers, mixers and oscillators Focuses on the application potential of non-linear components Practicing engineers and circuit designers working in microwave and communications engineering and designing new applications, as well as senior undergraduates, graduate students and researchers in microwave and communications engineering and their libraries will find this a highly rewarding read.
Download or read book IEEE ACM International Conference on Computer Aided Design written by International Conference on Computer Aided Design. Institute of Electrical and Electronics Engineers, 2000, San José, Calif.. and published by . This book was released on 2000 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Journal of Research of the National Bureau of Standards written by United States. National Bureau of Standards and published by . This book was released on 1960 with total page 832 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modeling and Design Techniques for RF Power Amplifiers written by Arvind Raghavan and published by John Wiley & Sons. This book was released on 2008-01-09 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Achieve higher levels of performance, integration, compactness, and cost-effectiveness in the design and modeling of radio-frequency (RF) power amplifiers RF power amplifiers are important components of any wireless transmitter, but are often the limiting factors in achieving better performance and lower cost in a wireless communication system—presenting the RF IC design community with many challenges. The next-generation technological advances presented in this book are the result of cutting-edge research in the area of large-signal device modeling and RF power amplifier design at the Georgia Institute of Technology, and have the potential to significantly address issues of performance and cost-effectiveness in this area. Richly complemented with hundreds of figures and equations, Modeling and Design Techniques for RF Power Amplifiers introduces and explores the most important topics related to RF power amplifier design under one concise cover. With a focus on efficiency enhancement techniques and the latest advances in the field, coverage includes: Device modeling for CAD Empirical modeling of bipolar devices Scalable modeling of RF MOSFETs Power amplifier IC design Power amplifier design in silicon Efficiency enhancement of RF power amplifiers The description of state-of-the-art techniques makes this book a valuable and handy reference for practicing engineers and researchers, while the breadth of coverage makes it an ideal text for graduate- and advanced undergraduate-level courses in the area of RF power amplifier design and modeling.
Download or read book Journal of Research written by United States. National Bureau of Standards and published by . This book was released on 1959 with total page 1136 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electrical Electronics Abstracts written by and published by . This book was released on 1997 with total page 2240 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The RF and Microwave Handbook written by Mike Golio and published by CRC Press. This book was released on 2000-12-20 with total page 1377 pages. Available in PDF, EPUB and Kindle. Book excerpt: The recent shift in focus from defense and government work to commercial wireless efforts has caused the job of the typical microwave engineer to change dramatically. The modern microwave and RF engineer is expected to know customer expectations, market trends, manufacturing technologies, and factory models to a degree that is unprecedented in the
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nonlinear Dynamics Volume 2 written by Gaetan Kerschen and published by Springer Science & Business Media. This book was released on 2014-03-28 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: This second volume of eight from the IMAC - XXXII Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on fundamental and applied aspects of Structural Dynamics, including papers on: Linear Systems Substructure Modelling Adaptive Structures Experimental Techniques Analytical Methods Damage Detection Damping of Materials & Members Modal Parameter Identification Modal Testing Methods System Identification Active Control Modal Parameter Estimation Processing Modal Data
Download or read book Grid Connected Converters written by Hassan Bevrani and published by Elsevier. This book was released on 2022-08-11 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: Grid Connected Converters: Modeling, Stability and Control discusses the foundations and core applications of this diverse field, from structure, modeling and dynamic equivalencing through power and microgrids dynamics and stability, before moving on to controller synthesis methodologies for a powerful range of applications. The work opens with physical constraints and engineering aspects of advanced control schemes. Robust and adaptive control strategies are evaluated using real-time simulation and experimental studies. Once foundations have been established, the work goes on to address new technical challenges such as virtual synchronous generators and synergic inertia emulation in response to low inertia challenges in modern power grids.The book also addresses advanced systematic control synthesis methodologies to enhance system stability and dynamic performance in the presence of uncertainties, practical constraints and cyberattacks. - Addresses new approaches for modeling, stability analysis and control design of GCCs - Proposes robust and flexible GCC control frameworks for supporting grid regulation - Emphasizes the application of GCCs in inertia emulation, oscillation damping control, and dynamic shaping - Addresses systematic control synthesis methodologies for system security and dynamic performance
Download or read book Microwave Wireless Communications written by Antonio Raffo and published by Academic Press. This book was released on 2016-03-01 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt: To design and develop fast and effective microwave wireless systems today involves addressing the three different 'levels': Device, circuit, and system. This book presents the links and interactions between the three different levels rather than providing just a comprehensive coverage of one specific level. With the aim of overcoming the sectional knowledge of microwave engineers, this will be the first book focused on explaining how the three different levels interact by taking the reader on a journey through the different levels going from the theoretical background to the practical applications. - Explains the links and interactions between the three different design levels of wireless communication transmitters: device, circuit, and system - Presents state-of-the-art, challenges, and future trends in the field of wireless communication systems - Covers all aspects of both mature and cutting-edge technologies for semiconductor devices for wireless communication applications - Many circuit designs outlining the limitations derived from the available transistor technologies and system requirements - Explains how new microwave measurement techniques can represent an essential tool for microwave modellers and designers
Download or read book Improving the speed and convergence of DC analysis by means of self generating lookup tables and piecewise linear analysis written by Janne Roos and published by . This book was released on 1999 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt:
