Download or read book Comparison of Additively Manufactured and Wrought 17 4 PH Stainless Steels in Ultra Low Cycle Fatigue written by Timothy Strasser and published by . This book was released on 2020 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) processes allow for creation of complex geometries that are otherwise impractical to fabricate with traditional subtractive methods. AM technology has potential to improve the optimization of seismic lateral force resisting components which dissipate seismic energy through large plastic strains; however, the ultra low-cycle fatigue performance of AM metals are not yet well understood. Void formation during the AM fabrication process has potential to affect performance. This study compares the performance of heat-treated and non-heat-treated AM and wrought 17-4PH stainless steel in Ultra Low Cycle Fatigue. To understand ULCF performance differences between the AM and wrought specimens, post fracture microstructure, fractography, surface hardness, and material characterizations are conducted. Results indicate reduced fatigue life for AM 17-4PH stainless steel as compared to the wrought counterparts. Fatigue life reductions of 62% and 65% were measured for the AM steel materials (as compared to the wrought counterparts) at 3% and 4% applied strain amplitude respectively. Applied material heat treatments had no observable effect on ULCF performance.
Download or read book Behavior of Materials Under Conditions of Thermal Stress written by S. S. Manson and published by . This book was released on 1953 with total page 730 pages. Available in PDF, EPUB and Kindle. Book excerpt: A review is presented of available information on the behavior of brittle and ductile materials under conditions of thermal stress and thermal shock. For brittle materials, a simple formula relating physical properties to thermal-shock resistance are derived and used to determine the relative significance of two indices currently in use for rating materials. The importance of simulating operating conditions in thermal-shock testing is deduced from the formula and is experimentally illustrated by showing that BeO could be both inferior or superior to Al2O3 in thermal shock depending on the testing conditions. For ductile materials, thermal-shock resistance depends upon the complex interrelation among several metallurgical variables which seriously affect strength and ductility. These variables are briefly discussed and illustrated from literature sources. The importance of simulating operating conditions in tests for rating ductile materials is especially to be emphasized because of the importance of testing conditions in metallurgy. A number of practical methods that have been used to minimize the deleterious effects of thermal stress and thermal shock are outlined.
Download or read book Springer Handbook of Additive Manufacturing written by Eujin Pei and published by Springer Nature. This book was released on 2023-11-25 with total page 994 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook is the ultimate definitive guide that covers key fundamentals and advanced applications for Additive Manufacturing. The Handbook has been structured into seven sections, comprising of a thorough Introduction to Additive Manufacturing; Design and Data; Processes; Materials; Post-processing, Testing and Inspection; Education and Training; and Applications and Case Study Examples. The general principles and functional relationships are described in each chapter and supplemented with industry use cases. The aim of this book is to help designers, engineers and manufacturers understand the state-of-the-art developments in the field of Additive Manufacturing. Although this book is primarily aimed at students and educators, it will appeal to researchers and industrial professionals working with technology users, machine or component manufacturers to help them make better decisions in the implementation of Additive Manufacturing and its applications.
Download or read book The Effect of Heat Treatment on Mechanical Properties of Additively Manufactured 17 4 PH Stainless Steel written by Nicholas Aaron Hopkins and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is used to create geometries otherwise impossible to machine. Topology optimization, microstructural texture control, and the use of lattices could be created through AM to increase performance of systems. Currently research focuses on solution aging of printed 17-4 PH, while other heat treatments are not as heavily studied. This study identifies different heat treatments applied to additively manufactured 17-4 precipitation hardened (PH) and the effects on mechanical properties. This study used quasi-static tension, quasi-static compression, and Charpy V-notch testing to analyze the effects of heat treatment as well as the effectiveness of additive manufacturing compared to traditional machining for wrought materials. Data during testing was taken with digital image correlation to identify changes in local strain. The effectiveness of heat treatment was demonstrated in this study and can be used to estimate performance on additively produced 17-4 PH.
Download or read book WELDING METALLURGY AND WELDABILITY OF STAINLESS STEELS written by John C. Lippold and published by . This book was released on 2011-01-01 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Market_Desc: · Professional engineers, technicians, scientists, etc. working in industries where stainless steels are used for construction. This includes the power generation, energy, petrochemical, dairy, medical, electronic, defense, and construction industries.· Advanced undergraduate and graduate level students. Special Features: · Emphasizes solid fundamental underpinnings of the metallurgical principles that govern microstructure evolution and property develpment in welded stainless steels.· Presents many practical examples that demonstrate the application of fundamental metallurgical principles.· Greatly expands and updates what is currently available in other texts and handbooks in the subject matter. About The Book: This book describes the fundamental metallurgical principles that control microstructure and properties of welded stainless steels. It also serves as a practical how to guide that will allow engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to insure that failures are avoided during fabrication and service. This book provides state of the art information on the topic and greatly expands and update what is currently available in other texts and handbooks.
Download or read book Manufacturing and Application of Stainless Steels written by Andrea Di Schino and published by MDPI. This book was released on 2020-04-15 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stainless steels represent a quite interesting material family, both from a scientific and commercial point of view, following to their excellent combination in terms of strength and ductility together with corrosion resistance. Thanks to such properties, stainless steels have been indispensable for the technological progress during the last century and their annual consumption increased faster than other materials. They find application in all these fields requiring good corrosion resistance together with ability to be worked into complex geometries. Despite to their diffusion as a consolidated materials, many research fields are active regarding the possibility to increase stainless steels mechanical properties and corrosion resistance by grain refinement or by alloying by interstitial elements. At the same time innovations are coming from the manufacturing process of such a family of materials, also including the possibility to manufacture them starting from metals powder for 3D printing. The Special Issue scope embraces interdisciplinary work covering physical metallurgy and processes, reporting about experimental and theoretical progress concerning microstructural evolution during processing, microstructure-properties relations, applications including automotive, energy and structural.
Download or read book Multiaxial Notch Fatigue written by Luca Susmel and published by Elsevier. This book was released on 2009-03-20 with total page 589 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal and composite components used in structural engineering not only contain geometrical features resulting in stress concentration phenomena, but they are also subjected to in-service multiaxial fatigue loading. To address the problem, structural engineers need reliable methodologies which allow for an adequate margin of safety. The book summarises methods devised by the author to design real components against multiaxial fatigue by taking full advantage not only of nominal but also of local stress-strain quantities.The book begins by reviewing definitions suitable for calculating the stress-strain quantities commonly used to perform fatigue assessment. The Modified Wöhler Curve Method is then explained in detail, by focusing attention on both the high- and the medium-cycle fatigue regime. The existing links between the multiaxial fatigue criterion and physical properties are also discussed. A procedure suitable for employing the method developed by the author to estimate fatigue damage both in notched and in welded components is explained. The Modified Manson-Coffin Curve method is investigated in depth, by reviewing those concepts playing a fundamental role in the so-called strain based approach. Lastly, the problem of performing the fatigue assessment of composite materials is addressed by considering design parameters influencing composite behaviour under complex cyclic loading paths and those criteria suitable for designing real components against multiaxial fatigue. The book also contains two appendices summarising experimental data from the technical literature. These appendices provide a unique and highly valuable resource for engineers. The appendices summarise around 100 values of the material characteristic length L, experimentally determined by testing specimens made of different engineering materials and about 4500 experimental fatigue results generated by testing plain, notched and welded specimens under constant-amplitude proportional and non-proportional multiaxial fatigue loading are listed. - Summarises methods devised by the author to design real components against multiaxial fatigue - Reviews definitions suitable for calculating the stress-strain quantities commonly used to perform fatigue assessment - Includes an in-depth explanation of both the Modified Wöhler Curve and Modified Manson-Coffin Curve Method
Download or read book Phase Transformations in Steels written by Elena Pereloma and published by Elsevier. This book was released on 2012-05-11 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: The processing-microstructure-property relationships in steels continue to present challenges to researchers because of the complexity of phase transformation reactions and the wide spectrum of microstructures and properties achievable. This major two-volume work summarises the current state of research on phase transformations in steels and its implications for the emergence of new steels with enhanced engineering properties.Volume 1 reviews fundamentals and diffusion-controlled phase transformations. After a historical overview, chapters in part one discuss fundamental principles of thermodynamics, diffusion and kinetics as well as phase boundary interfaces. Chapters in part two go on to consider ferrite formation, proeutectoid ferrite and cementite transformations, pearlite formation and massive austenite-ferrite phase transformations. Part three discusses the mechanisms of bainite transformations, including carbide-containing and carbide-free bainite. The final part of the book considers additional driving forces for transformation including nucleation and growth during austenite-to-ferrite phase transformations, dynamic strain-induced ferrite transformations (DIST) as well as the effects of magnetic fields and heating rates.With its distinguished editors and distinguished international team of contributors, the two volumes of Phase transformations in steels is a standard reference for all those researching the properties of steel and developing new steels in such areas as automotive engineering, oil and gas and energy production. - Discusses the fundamental principles of thermodynamics, diffusion and kinetics - Considers various transformations, including ferrite formation, proeutectoid ferrite and cementite transformations - Considers additional driving forces for transformation including nucleation and growth during austenite-to-ferrite phase transformations
Download or read book Additive Manufacturing of Metals written by John O. Milewski and published by Springer. This book was released on 2017-06-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This engaging volume presents the exciting new technology of additive manufacturing (AM) of metal objects for a broad audience of academic and industry researchers, manufacturing professionals, undergraduate and graduate students, hobbyists, and artists. Innovative applications ranging from rocket nozzles to custom jewelry to medical implants illustrate a new world of freedom in design and fabrication, creating objects otherwise not possible by conventional means. The author describes the various methods and advanced metals used to create high value components, enabling readers to choose which process is best for them. Of particular interest is how harnessing the power of lasers, electron beams, and electric arcs, as directed by advanced computer models, robots, and 3D printing systems, can create otherwise unattainable objects. A timeline depicting the evolution of metalworking, accelerated by the computer and information age, ties AM metal technology to the rapid evolution of global technology trends. Charts, diagrams, and illustrations complement the text to describe the diverse set of technologies brought together in the AM processing of metal. Extensive listing of terms, definitions, and acronyms provides the reader with a quick reference guide to the language of AM metal processing. The book directs the reader to a wealth of internet sites providing further reading and resources, such as vendors and service providers, to jump start those interested in taking the first steps to establishing AM metal capability on whatever scale. The appendix provides hands-on example exercises for those ready to engage in experiential self-directed learning.
Download or read book Multiaxial Fatigue written by Darrell Socie and published by SAE International. This book was released on 1999-12-15 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides practicing engineers, researchers, and students with a working knowledge of the fatigue design process and models under multiaxial states of stress and strain. Readers are introduced to the important considerations of multiaxial fatigue that differentiate it from uniaxial fatigue.
Download or read book Powder Injection Molding written by Randall M. German and published by . This book was released on 2003 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Analysis of 3D Printed 15 5 PH Stainless Steel written by Anudeep Padmanabhan and published by . This book was released on 2019 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) or 3D printing has gained significant advancement in recent years. However the potential of 3D printed metals still has not been fully explored. A main reason is the lack of accurate knowledge of the load capacity of 3D printed metals, such as fatigue behavior under cyclic load conditions, which is still poorly understood as compared with the conventional wrought counterpart. The goal of the thesis is to advance the knowledge of fatigue behavior of 15-5 PH stainless steel manufactured through laser powder bed fusion process. To achieve the goal, a combined numerical and experimental study is carried out. First, using a rotary fatigue testing experiment, the fatigue life of the 15-5 PH stainless steel is measured. The strain life curve shows that the numbers of the reversals to failure increase from 13,403 to 46,760 as the applied strain magnitudes decrease from 0.214\% from 0.132\%, respectively. The micro-structure analysis shows that predominantly brittle fracture is presented on the fractured surface. Second, a finite element model based on cyclic plasticity including the damage model is developed to predict the fatigue life. The model is calibrated with two cases: one is the fatigue life of 3D printed 17-4 stainless steel under constant amplitude strain load using the direct cyclic method, and the other one is the cyclic behavior of Alloy 617 under multi-amplitude strain loads using the static analysis method. Both validation models show a good correlation with the literature experimental data. Finally, after the validation, the finite element model is applied to the 15-5 PH stainless steel. Using the direct cyclic method, the model predicts the fatigue life of 15-5 PH stainless steel under constant amplitude strain. The extension of the prediction curve matches well with the previously measured experimental results, following the combined Coffin-Manson Basquin Law. Under multi-amplitude strain, the kinematic hardening evolution parameter is incorporated into the model. The model is capable to capture the stresses at varied strain amplitudes. Higher stresses are predicted when strain amplitudes are increased. The model presented in the work can be used to design reliable 3D printed metals under cyclic loading conditions.
Download or read book TMS 2020 149th Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer Nature. This book was released on 2020-02-13 with total page 2046 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents papers from the 149th Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.
Download or read book Laser Additive Manufacturing written by Milan Brandt and published by Woodhead Publishing. This book was released on 2016-09-01 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser Additive Manufacturing: Materials, Design, Technologies, and Applications provides the latest information on this highly efficient method of layer-based manufacturing using metals, plastics, or composite materials. The technology is particularly suitable for the production of complex components with high precision for a range of industries, including aerospace, automotive, and medical engineering. This book provides a comprehensive review of the technology and its range of applications. Part One looks at materials suitable for laser AM processes, with Part Two discussing design strategies for AM. Parts Three and Four review the most widely-used AM technique, powder bed fusion (PBF) and discuss other AM techniques, such as directed energy deposition, sheet lamination, jetting techniques, extrusion techniques, and vat photopolymerization. The final section explores the range of applications of laser AM. Provides a comprehensive one-volume overview of advances in laser additive manufacturing Presents detailed coverage of the latest techniques used for laser additive manufacturing Reviews both established and emerging areas of application
Download or read book Fatigue Data on Precipitation hardenable Stainless Steels written by R. J. Favor and published by . This book was released on 1960 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Theory of Notch Stresses written by Heinz Neuber and published by . This book was released on 1946 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stainless Steels for Design Engineers written by Michael F. McGuire and published by ASM International. This book was released on 2008 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: The rate of growth of stainless steel has outpaced that of other metals and alloys, and by 2010 may surpass aluminum as the second most widely used metal after carbon steel. The 2007 world production of stainless steel was approximately 30,000,000 tons and has nearly doubled in the last ten years. This growth is occurring at the same time that the production of stainless steel continues to become more consolidated. One result of this is a more widespread need to understand stainless steel with fewer resources to provide that information. The concurrent technical evolution in stainless steel and increasing volatility of raw material prices has made it more important for the engineers and designers who use stainless steel to make sound technical judgments about which stainless steels to use and how to use them.
