Download or read book Comparison Between Aqueous and Vapor phase Reformation for Thermochemical Waste Heat Recovery of Engine Exhaust Gas written by Mark Aaronian Severy and published by . This book was released on 2013 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas internal combustion engines release over half of the fuel's energy as waste heat and emit pollution that harms human health and accelerates climate change. Enriching natural gas with hydrogen has been shown to mitigate these impacts by reducing emissions and increasing engine efficiency. Thermal energy in the exhaust gas from natural gas engines can be used to drive chemical reactions to reform a biomass-derived feedstock into a hydrogen-rich gas. This gas can be blended with the primary fuel to enhance combustion and displace some of the natural gas demand. Two types of chemical reformation processes, aqueous-phase reformation (APR) and vapor-phase reformation (VPR), have been identified which can convert a biomass-derived sugar feedstock solution into a hydrogen-rich gas by recovering waste heat from engine exhaust gas. VPR operates at higher temperatures than APR, which limits the amount of heat that can be transferred from the exhaust gas to the reaction temperature. This study used a thermodynamic pinch analysis to compare the performance of these two processes based on their respective process heat demands and the thermal energy available from engine exhaust gas to determine how many moles of feedstock can be reformed. The calculations were performed using specifications for eight natural gas engines with reactor conditions from fourteen APR and ten VPR experiments, using glycerol as a model compound.
Download or read book Analysis of Exhaust Waste Heat Recovery Techniques from Stationary Power Generation Engines Using Organic Rankine Cycles written by Devin Krishna Sham and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Strict emissions legislation and energy security debates have spurred extensive research in alternative fuels and renewable energies. Literature research has shown the need for improvements in internal combustion engines (ICE) due to their low efficiencies. Significant gains in efficiency can be accomplished with the use of waste heat recovery (WHR) techniques. Organic rankine cycles (ORC) with turbocompounding harness the waste heat from an ICE to improve efficiency and fuel economy while reducing brake-specific emissions. A mathematical model was developed to explore the potential gains in 1st and 2nd law efficiencies. The model approaches the evaluations of the ORC from a practical and a theoretical method. The practical method in evaluation 1 limits the outlet exhaust gas temperatures from the evaporator to prevent the formation of condensation. The performance of the ORC is then evaluated and compared to the evaluation 2. In the theoretical method, in evaluation 2, the effect of pinch point on the evaporator and the entire cycle was analyzed. This analysis was conducted for R113, a dry fluid, and propane, a wet fluid, in order to analyze the differences in the two types of fluids. R113 showed a 13% -- 22% and a 6% -- 14.7% increase in 1st and 2nd law efficiencies, respectively. Propane showed a 9% -- 17.4% and a 2% -- 8.5% increase in 1st and 2nd law efficiencies, respectively. It was also shown that as the pinch point temperature decreases the 2nd law efficiencies increased. It was concluded that use of ORC with turbocompounding is an effective method for waste heat recovery in order to increase ICE efficiency.
Download or read book A Study of the Theoretical Potential of Thermochemical Exhaust Heat Recuperation for Internal Combustion Engines written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: We present a detailed thermodynamic analysis of thermochemical recuperation (TCR) applied to an idealized internal combustion engine with single-stage work extraction. Results for several different fuels are included. For a stoichiometric mixture of methanol and air, TCR can increase the estimated ideal engine Second Law efficiency by about 3% for constant pressure reforming and over 5% for constant volume reforming. For ethanol and isooctane the estimated Second Law efficiency increases for constant volume reforming are 9% and 11%, respectively. The Second Law efficiency improvements from TCR result primarily from the higher intrinsic exergy of the reformed fuel and pressure boost associated with gas mole increase. Reduced combustion irreversibility may also yield benefits for future implementations of combined cycle work extraction.
Download or read book Alternatives in Refrigeration and Air Conditioning written by S. C. Kaushik and published by I K International Pvt Ltd. This book was released on 2016-04-19 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highlights the issues related to ozone layer depletion and global warming due to use of conventional cooling technologies and refrigerants in the field of Refrigeration and Air Conditioning (RAC). It describes, simulates and analyses the alternate technologies and alternate refrigerants. Unconventional refrigeration technologies are explored.
Download or read book Biomass Gasification and Pyrolysis written by Prabir Basu and published by Academic Press. This book was released on 2010-07-19 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers comprehensive coverage of the design, analysis, and operational aspects of biomass gasification, the key technology enabling the production of biofuels from all viable sources--some examples being sugar cane and switchgrass. This versatile resource not only explains the basic principles of energy conversion systems, but also provides valuable insight into the design of biomass gasifiers. The author provides many worked out design problems, step-by-step design procedures and real data on commercially operating systems. After fossil fuels, biomass is the most widely used fuel in the world. Biomass resources show a considerable potential in the long term if residues are properly handled and dedicated energy crops are grown. Includes step-by-step design procedures and case studies for Biomass GasificationProvides worked process flow diagrams for gasifier design. Covers integration with other technologies (e.g. gas turbine, engine, fuel cells)
Download or read book Progress in Thermochemical Biomass Conversion written by A. V. Bridgwater and published by John Wiley & Sons. This book was released on 2008-04-30 with total page 1744 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is for chemical engineers, fuel technologists, agricultural engineers and chemists in the world-wide energy industry and in academic, research and government institutions. It provides a thorough review of, and entry to, the primary and review literature surrounding the subject. The authors are internationally recognised experts in their field and combine to provide both commercial relevance and academic rigour. Contributions are based on papers delivered to the Fifth International Conference sponsored by the IEA Bioenergy Agreement.
Download or read book Handbook of Diesel Engines written by Klaus Mollenhauer and published by Springer Science & Business Media. This book was released on 2010-06-22 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt: This machine is destined to completely revolutionize cylinder diesel engine up through large low speed t- engine engineering and replace everything that exists. stroke diesel engines. An appendix lists the most (From Rudolf Diesel’s letter of October 2, 1892 to the important standards and regulations for diesel engines. publisher Julius Springer. ) Further development of diesel engines as economiz- Although Diesel’s stated goal has never been fully ing, clean, powerful and convenient drives for road and achievable of course, the diesel engine indeed revolu- nonroad use has proceeded quite dynamically in the tionized drive systems. This handbook documents the last twenty years in particular. In light of limited oil current state of diesel engine engineering and technol- reserves and the discussion of predicted climate ogy. The impetus to publish a Handbook of Diesel change, development work continues to concentrate Engines grew out of ruminations on Rudolf Diesel’s on reducing fuel consumption and utilizing alternative transformation of his idea for a rational heat engine fuels while keeping exhaust as clean as possible as well into reality more than 100 years ago. Once the patent as further increasing diesel engine power density and was filed in 1892 and work on his engine commenced enhancing operating performance.
Download or read book Handbook of Alternative Fuel Technologies Second Edition written by Sunggyu Lee and published by CRC Press. This book was released on 2014-07-08 with total page 706 pages. Available in PDF, EPUB and Kindle. Book excerpt: While strides are being made in the research and development of environmentally acceptable and more sustainable alternative fuels—including efforts to reduce emissions of air pollutants associated with combustion processes from electric power generation and vehicular transportation—fossil fuel resources are limited and may soon be on the verge of depletion in the near future. Measuring the correlation between quality of life, energy consumption, and the efficient utilization of energy, the Handbook of Alternative Fuel Technologies, Second Edition thoroughly examines the science and technology of alternative fuels and their processing technologies. It focuses specifically on environmental, technoeconomic, and socioeconomic issues associated with the use of alternative energy sources, such as sustainability, applicable technologies, modes of utilization, and impacts on society. Written with research and development scientists and engineers in mind, the material in this handbook provides a detailed description and an assessment of available and feasible technologies, environmental health and safety issues, governmental regulations, and issues and agendas for R&D. It also includes alternative energy networks for production, distribution, and consumption. What’s New in This Edition: Contains several new chapters of emerging interest and updates various chapters throughout Includes coverage of coal gasification and liquefaction, hydrogen technology and safety, shale fuel by hydraulic fracturing, ethanol from lignocellulosics, biodiesel, algae fuels, and energy from waste products Covers statistics, current concerns, and future trends A single-volume complete reference, the Handbook of Alternative Fuel Technologies, Second Edition contains relevant information on chemistry, technology, and novel approaches, as well as scientific foundations for further enhancements and breakthroughs. In addition to its purposes as a handbook for practicing scientists and engineers, it can also be used as a textbook or as a reference book on fuel science and engineering, energy and environment, chemical process design, and energy and environmental policy.
Download or read book Renewable Energy Sources and Climate Change Mitigation written by Ottmar Edenhofer and published by Cambridge University Press. This book was released on 2011-11-21 with total page 1088 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Intergovernmental Panel on Climate Change Special Report (IPCC-SRREN) assesses the potential role of renewable energy in the mitigation of climate change. It covers the six most important renewable energy sources - bioenergy, solar, geothermal, hydropower, ocean and wind energy - as well as their integration into present and future energy systems. It considers the environmental and social consequences associated with the deployment of these technologies, and presents strategies to overcome technical as well as non-technical obstacles to their application and diffusion. SRREN brings a broad spectrum of technology-specific experts together with scientists studying energy systems as a whole. Prepared following strict IPCC procedures, it presents an impartial assessment of the current state of knowledge: it is policy relevant but not policy prescriptive. SRREN is an invaluable assessment of the potential role of renewable energy for the mitigation of climate change for policymakers, the private sector, and academic researchers.
Download or read book Diesel and Gasoline Engines written by Richard Viskup and published by . This book was released on 2020-02 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: The internal combustion engine was invented around 1790 by various scientists and engineers worldwide. Since then the engines have gone through many modifications and improvements. Today, different applications of engines form a significant technological importance in our everyday lives, leading to the evolution of our modern civilization. The invention of diesel and gasoline engines has definitely changed our lifestyles as well as shaped our priorities. The current engines serve innumerable applications in various types of transportation, in harsh environments, in construction, in diverse industries, and also as back-up power supply systems for hospitals, security departments, and other institutions. However, heavy duty or light duty engines have certain major disadvantages, which are well known to everyone. With the increasing usage of diesel and gasoline engines, and the constantly rising number of vehicles worldwide, the main concern nowadays is engine exhaust emissions. This book looks at basic phenomena related to diesel and gasoline engines, combustion, alternative fuels, exhaust emissions, and mitigations.
Download or read book Recent Advances in Pyrolysis written by Hassan Al- Haj Ibrahim and published by BoD – Books on Demand. This book was released on 2020-01-22 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pyrolysis is an irreversible thermochemical treatment process of materials at elevated temperatures in an inert atmosphere. It is basically a carbonisation process where an organic material is decomposed to produce a solid residue with high (or higher) carbon content and some volatile products. The decomposition reactions are accompanied in general with polymerisation and isomerisation reactions. The end products of pyrolysis can be controlled by optimizing pyrolysis parameters such as temperature and residence time. Pyrolysis is used heavily in the chemical industry to produce many forms of carbon and other chemicals from petroleum, coal, wood, oil shale, biomass or organic waste materials, and it is the basis of several methods for producing fuel from biomass. Pyrolysis also is the process of conversion of buried organic matter into fossil fuels.
Download or read book Biohydrogen written by Ayhan Demirbas and published by Springer Science & Business Media. This book was released on 2009-06-30 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biohydrogen: For Future Engine Fuel Demands covers the production, purification, storage, pipeline transport, usage, and safety of biohydrogen. Hydrogen promises to be the most significant fuel source of the future, due to its global availability and the fact that water is its only by-product. Biofuels such as bioethanol, biodiesel, bio-oil, and biohydrogen are produced using technologies for thermochemically and biologically converting biomass. Hydrogen fuel production technologies can make use of either non-renewable sources, or renewable sources such as wind, solar, and biorenewable resources. Biohydrogen: For Future Engine Fuel Demands reviews all of the modern biomass-based transportation fuels, including bioethanol, biodiesel, biogas, biohydrogen, and fuel cells. The book also discusses issues of biohydrogen economy, policy and environmental impact. Biohydrogen looks set to be the fuel of choice in the future, replacing both fossil fuels and biorenewable liquid fuels.
Download or read book Hydrogen Technology written by Aline Léon and published by Springer Science & Business Media. This book was released on 2008-07-18 with total page 680 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aline Leon ́ In the last years, public attention was increasingly shifted by the media and world governmentsto the conceptsof saving energy,reducingpollution,protectingthe - vironment, and developing long-term energy supply solutions. In parallel, research funding relating to alternative fuels and energy carriers is increasing on both - tional and international levels. Why has future energy supply become such a matter of concern? The reasons are the problems created by the world’s current energy supply s- tem which is mainly based on fossil fuels. In fact, the energystored in hydrocarb- based solid, liquid, and gaseous fuels was, is, and will be widely consumed for internal combustion engine-based transportation, for electricity and heat generation in residential and industrial sectors, and for the production of fertilizers in agric- ture, as it is convenient, abundant, and cheap. However, such a widespread use of fossil fuels by a constantly growing world population (from 2. 3 billion in 1939 to 6. 5 billion in 2006) gives rise to the two problems of oil supply and environmental degradation. The problemrelated to oil supply is caused by the fact that fossil fuels are not - newable primary energy sources: This means that since the rst barrel of petroleum has been pumped out from the ground, we have been exhausting a heritage given by nature.
Download or read book Steam Generators and Waste Heat Boilers written by V. Ganapathy and published by CRC Press. This book was released on 2014-10-10 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: Incorporates Worked-Out Real-World Problems Steam Generators and Waste Heat Boilers: For Process and Plant Engineers focuses on the thermal design and performance aspects of steam generators, HRSGs and fire tube, water tube waste heat boilers including air heaters, and condensing economizers. Over 120 real-life problems are fully worked out which will help plant engineers in evaluating new boilers or making modifications to existing boiler components without assistance from boiler suppliers. The book examines recent trends and developments in boiler design and technology and presents novel ideas for improving boiler efficiency and lowering gas pressure drop. It helps plant engineers understand and evaluate the performance of steam generators and waste heat boilers at any load. Learn How to Independently Evaluate the Thermal Performance of Boilers and Their Components This book begins with basic combustion and boiler efficiency calculations. It then moves on to estimation of furnace exit gas temperature (FEGT), furnace duty, view factors, heat flux, and boiler circulation calculations. It also describes trends in large steam generator designs such as multiple-module; elevated drum design types of boilers such as D, O, and A; and forced circulation steam generators. It illustrates various options to improve boiler efficiency and lower operating costs. The author addresses the importance of flue gas analysis, fire tube versus water tube boilers used in chemical plants, and refineries. In addition, he describes cogeneration systems; heat recovery in sulfur plants, hydrogen plants, and cement plants; and the effect of fouling factor on performance. The book also explains HRSG simulation process and illustrates calculations for complete performance evaluation of boilers and their components. Helps plant engineers make independent evaluations of thermal performance of boilers before purchasing them Provides numerous examples on boiler thermal performance calculations that help plant engineers develop programming codes with ease Follows the metric and SI system, and British units are shown in parentheses wherever possible Includes calculation procedures for the basic sizing and performance evaluation of a complete steam generator or waste heat boiler system and their components with appendices outlining simplified procedures for estimation of heat transfer coefficients Steam Generators and Waste Heat Boilers: For Process and Plant Engineers serves as a source book for plant engineers, consultants, and boiler designers.
Download or read book Hydrogen Energy written by David Anthony James Rand and published by Royal Society of Chemistry. This book was released on 2008 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: A transition to renewable and low-carbon forms of energy is being widely debated as a means of securing a sustainable future for mankind. Hydrogen Energy Challenges and Prospects, a new book from the authors of Clean Energy, considers the prospects for hydrogen as a universal energy vector and fuel for the decades to come. With no emissions other than water arising from its combustion, the potential virtues of harnessing and utilizing hydrogen correlate with recent growing concern over the security of conventional fuel supply and global climate change. This book sets out to analyze the technical situation in an objective fashion, free from the constraints of political and industrial loyalties. Areas covered include pathways to hydrogen production, prospects for carbon capture and storage, options for hydrogen storage on vehicles, fuel cells, and fuel cell vehicles. Each of the many facets of hydrogen energy is discussed and the challenges to be faced are addressed. The authors acknowledge it is not possible to reach a simple, unequivocal conclusion regarding overall prospects, since the international energy scene is so complex, and predicting long-term futures is so notoriously difficult. Nevertheless, the reader will be given compelling pointers indicative of the way in which events might develop. This topical book is ideal for undergraduates, postgraduates and academics with an interest in hydrogen energy. Government agencies and energy professionals will also find this content to be a useful reference source.
Download or read book Biomass Gasifier tars written by Thomas A. Milne and published by . This book was released on 1999 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Successful Approaches to Recycling Urban Wood Waste written by and published by . This book was released on 2002 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents eight case studies of successful urban wood waste recycling projects and businesses. These studies document the success of recovered products such as lumber and lumber products, mulch, boiler fuel, and alternative cover for landfills. Overall, wood waste accounts for about 17% of the total waste received at municipal solid waste landfills in the United States. In 1998, the amount of urban wood waste generated was more than 160 million tons, with 29.6 million tons available for recovery. Similarly, in 1998, new construction in the United States generated 8.7 million tons of wood waste, with 6.6 million tons available for recovery; demolition waste generated 26.4 million tons of wood waste, with 9 million tons available for recovery. The case studies were selected on the basis of the following criteria: an emphasis on partnerships among communities, businesses, governments, and non-governmental organizations; efficient use of funds; sustained creation of enterprise; and a high benefit/cost ratio.
