Download or read book Thermal Energy Storage Using Phase Change Materials written by Amy S. Fleischer and published by Springer. This book was released on 2015-06-22 with total page 97 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a comprehensive introduction to the use of solid‐liquid phase change materials to store significant amounts of energy in the latent heat of fusion. The proper selection of materials for different applications is covered in detail, as is the use of high conductivity additives to enhance thermal diffusivity. Dr. Fleischer explores how applications of PCMS have expanded over the past 10 years to include the development of high efficiency building materials to reduce heating and cooling needs, smart material design for clothing, portable electronic systems thermal management, solar thermal power plant design and many others. Additional future research directions and challenges are also discussed.
Download or read book Compact Solar Thermal Energy Storage Systems Using Phase Change Materials written by Maher Al-Maghalseh and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances in Concentrating Solar Thermal Research and Technology written by Manuel Blanco and published by Woodhead Publishing. This book was released on 2016-11-10 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: After decades of research and development, concentrating solar thermal (CST) power plants (also known as concentrating solar power (CSP) and as Solar Thermal Electricity or STE systems) are now starting to be widely commercialized. Indeed, the IEA predicts that by 2050, with sufficient support over ten percent of global electricity could be produced by concentrating solar thermal power plants. However, CSP plants are just but one of the many possible applications of CST systems. Advances in Concentrating Solar Thermal Research and Technology provides detailed information on the latest advances in CST systems research and technology. It promotes a deep understanding of the challenges the different CST technologies are confronted with, of the research that is taking place worldwide to address those challenges, and of the impact that the innovation that this research is fostering could have on the emergence of new CST components and concepts. It is anticipated that these developments will substantially increase the cost-competiveness of commercial CST solutions and reshape the technological landscape of both CST technologies and the CST industry. After an introductory chapter, the next three parts of the book focus on key CST plant components, from mirrors and receivers to thermal storage. The final two parts of the book address operation and control and innovative CST system concepts. Contains authoritative reviews of CST research taking place around the world Discusses the impact this research is fostering on the emergence of new CST components and concepts that will substantially increase the cost-competitiveness of CST power Covers both major CST plant components and system-wide issues
Download or read book Solar Thermal Energy Storage System using phase change material for uninterrupted on farm agricultural processing and value addition written by Anjum Munir and published by kassel university press GmbH. This book was released on 2019-10-09 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal energy storage technologies are gaining attention nowadays for uninterrupted supply of solar power in off-sunshine hours. An indigenized solar phase change material (PCM) system was developed and performance evaluated in the current study to efficiently store solar thermal power using a latent heat storage approach, which can be utilized in any subsequent decentralized food processing application. A 2.5 m2 laying Scheffler reflector is used to precisely focus the incoming direct normal irradiance (DNI) on a casted aluminum heat receiver (220 mm diameter) from where this concentrated heat energy is absorbed and conducted to the PCM unit by the flow of thermal oil (Fragoltherm-32 thermo-oil). During the circulation around PCM pipes inside the PCM unit, thermal oil discharges heat energy to the PCM, which undergoes change of phase from solid to liquid. Computational fluid dynamics (CFD) analysis of the PCM unit were also performed according to the actual boundary conditions, which gave satisfactory results in terms of temperature and velocity distribution. With an average DNI of 781 W/m2, the highest temperature of the receiver surface during the trials was observed at about 155 C that produces thermal oil at 110°C inside the receiver and around 48°C of PCM in the PCM unit. The heat energy losses per unit time (W) due to the lack of reflectivity from the Scheffler reflector, out-of-focus radiations at the targeted area, absorptivity of heat receiver, piping system losses, and cylinder losses (in the form of conduction, convection, and radiations using 50 mm insulation thickness) were found to be 110 W (10 %), 99 W (9 %), 89 W (8 %), 128 W (12 %), 161 W (15 %), and 89 W (8 %), respectively. These findings of CFD analysis and mathematical modeling were also consistent with real-time data, which was logged through an online Control and Monitoring Interface portal. The final energy available to the PCM was 414W with an overall system efficiency of 38 %, which can be improved by decreasing thermal losses of the system and using other PCM materials.
Download or read book Thermal Energy Storage with Phase Change Materials written by Mohammed Farid and published by CRC Press. This book was released on 2021-07-25 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on latent heat storage, which is one of the most efficient ways of storing thermal energy. Unlike the sensible heat storage method, the latent heat storage method provides much higher storage density with a smaller difference between storing and releasing temperatures. Thermal Energy Storage with Phase Change Materials is structured into four chapters that cover many aspects of thermal energy storage and their practical applications. Chapter 1 reviews selection, performance, and applications of phase change materials. Chapter 2 investigates mathematical analyses of phase change processes. Chapters 3 and 4 present passive and active applications for energy saving, peak load shifting, and price-based control heating using phase change materials. These chapters explore the hot topic of energy saving in an overarching way, and so they are relevant to all courses. This book is an ideal research reference for students at the postgraduate level. It also serves as a useful reference for electrical, mechanical, and chemical engineers and students throughout their work. FEATURES Explains the technical principles of thermal energy storage, including materials and applications in different classifications Provides fundamental calculations of heat transfer with phase change Discusses the benefits and limitations of different types of phase change materials (PCM) in both micro- and macroencapsulations Reviews the mechanisms and applications of available thermal energy storage systems Introduces innovative solutions in hot and cold storage applications
Download or read book High Temperature Thermal Storage Systems Using Phase Change Materials written by Luisa F. Cabeza and published by Academic Press. This book was released on 2017-11-27 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-Temperature Thermal Storage Systems Using Phase Change Materials offers an overview of several high-temperature phase change material (PCM) thermal storage systems concepts, developed by several well-known global institutions with increasing interest in high temperature PCM applications such as solar cooling, waste heat and concentrated solar power (CSP). The book is uniquely arranged by concepts rather than categories, and includes advanced topics such as thermal storage material packaging, arrangement of flow bed, analysis of flow and heat transfer in the flow bed, energy storage analysis, storage volume sizing and applications in different temperature ranges. By comparing the varying approaches and results of different research centers and offering state-of-the-art concepts, the authors share new and advanced knowledge from researchers all over the world. This reference will be useful for researchers and academia interested in the concepts and applications and different techniques involved in high temperature PCM thermal storage systems. Offers coverage of several high temperature PCM thermal storage systems concepts developed by several leading research institutions Provides new and advanced knowledge from researchers all over the world Includes a base of material properties throughout
Download or read book Thermal Energy Storage written by Ibrahim Dinçer and published by John Wiley & Sons. This book was released on 2011-06-24 with total page 585 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ability of thermal energy storage (TES) systems to facilitate energy savings, renewable energy use and reduce environmental impact has led to a recent resurgence in their interest. The second edition of this book offers up-to-date coverage of recent energy efficient and sustainable technological methods and solutions, covering analysis, design and performance improvement as well as life-cycle costing and assessment. As well as having significantly revised the book for use as a graduate text, the authors address real-life technical and operational problems, enabling the reader to gain an understanding of the fundamental principles and practical applications of thermal energy storage technology. Beginning with a general summary of thermodynamics, fluid mechanics and heat transfer, this book goes on to discuss practical applications with chapters that include TES systems, environmental impact, energy savings, energy and exergy analyses, numerical modeling and simulation, case studies and new techniques and performance assessment methods.
Download or read book Solar Thermal Energy Storage written by H.P. Garg and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 660 pages. Available in PDF, EPUB and Kindle. Book excerpt: Energy Storage not only plays an important role in conservinq the energy but also improves the performance and reliability of a wide range of energy systems. Energy storagp. leads to saving of premium fuels and makes the system morA cost effective by reducing the wastage of energy. In most systems there is a mismatch between the energy supply and energy demand. The energy storage can even out this imbalance and thereby help in savings of capital costs. Enerqy storage is all the more important where the enerqy source is intermittent such as Solar Energy. The use of jntermittent energy sources is likely to grow. If more and more solar energy is to be used for domestic and industrial applications then energy storage is very crucial. If no storage is used in solar energy systems then the major part of the energy demand will be met by the back-up or auxiliary energy and therefore the so called annual solar load fract]on will be very low. In case of solar energy, both short term and long term energy storage systems can be used whjch can adjust the phase difference between solar energy supply and energy demand and can match seasonal demands to the solar availability respectively. Thermal energy storage can lead to capital cost savings, fuel savjngs, and fuel substitution in many application areas. Developing an optimum thermal storaqe system is as important an area of research as developinq an alternative source of energy.
Download or read book Ultra High Temperature Thermal Energy Storage Transfer and Conversion written by Alejandro Datas and published by Woodhead Publishing. This book was released on 2020-09-01 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultra-High Temperature Thermal Energy Storage, Transfer and Conversion presents a comprehensive analysis of thermal energy storage systems operating at beyond 800°C. Editor Dr. Alejandro Datas and his team of expert contributors from a variety of regions summarize the main technological options and the most relevant materials and characterization considerations to enable the reader to make the most effective and efficient decisions.This book helps the reader to solve the very specific challenges associated with working within an ultra-high temperature energy storage setting. It condenses and summarizes the latest knowledge, covering fundamentals, device design, materials selection and applications, as well as thermodynamic cycles and solid-state devices for ultra-high temperature energy conversion.This book provides a comprehensive and multidisciplinary guide to engineers and researchers in a variety of fields including energy conversion, storage, cogeneration, thermodynamics, numerical methods, CSP, and materials engineering. It firstly provides a review of fundamental concepts before exploring numerical methods for fluid-dynamics and phase change materials, before presenting more complex elements such as heat transfer fluids, thermal insulation, thermodynamic cycles, and a variety of energy conversation methods including thermophotovoltaic, thermionic, and combined heat and power. Reviews the main technologies enabling ultra-high temperature energy storage and conversion, including both thermodynamic cycles and solid-state devices Includes the applications for ultra-high temperature energy storage systems, both in terrestrial and space environments Analyzes the thermophysical properties and relevant experimental and theoretical methods for the analysis of high-temperature materials
Download or read book Phase Change Materials for Solar Thermal Energy Storage written by Paul M. Allred and published by . This book was released on 2014 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: ABSTRACT: Phase change materials (PCMs) are a viable option for compact thermal energy storage. Effective designs using PCMs require accurate knowledge of the thermal and physical properties, but for many PCMs these are not well known, and when known the knowledge is sometimes contradictory. Therefore, physical characteristics of several promising PCMs (K3PO4·7H2O, FeCl3·6H2O, Mn(NO3)2·4H2O) were determined. In addition, a life cycle assessment (LCA) of dodecanoic acid in a solar thermal energy storage system was carried out to determine the environmental impact for energy storage. This LCA showed that dodecanoic acid in a solar energy system would save energy and facilitate CO2 reductions. However, the economic cost is high and is unlikely to be implemented without incentives. Finally an experimental testbed for a solar thermal system utilizing dodecanoic acid was built. Preliminary measurements demonstrated the utility of this system.
Download or read book Heat and cold storage with PCM written by Harald Mehling and published by Springer Science & Business Media. This book was released on 2008-08-15 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: The years 2006 and 2007 mark a dramatic change of peoples view regarding c- mate change and energy consumption. The new IPCC report makes clear that - mankind plays a dominant role on climate change due to CO emissions from en- 2 ergy consumption, and that a significant reduction in CO emissions is necessary 2 within decades. At the same time, the supply of fossil energy sources like coal, oil, and natural gas becomes less reliable. In spring 2008, the oil price rose beyond 100 $/barrel for the first time in history. It is commonly accepted today that we have to reduce the use of fossil fuels to cut down the dependency on the supply countries and to reduce CO emissions. The use of renewable energy sources and 2 increased energy efficiency are the main strategies to achieve this goal. In both strategies, heat and cold storage will play an important role. People use energy in different forms, as heat, as mechanical energy, and as light. With the discovery of fire, humankind was the first time able to supply heat and light when needed. About 2000 years ago, the Romans started to use ceramic tiles to store heat in under floor heating systems. Even when the fire was out, the room stayed warm. Since ancient times, people also know how to cool food with ice as cold storage.
Download or read book Solar Energy Utilization written by Hafit Yüncü and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 762 pages. Available in PDF, EPUB and Kindle. Book excerpt: Until very recently, energy supply of the world has been treated as being nearly inexhaustible. Nowadays about 90 percent of the energy used is obtained from non-renewable resources: oil, natural gas, coal and uranium. These resources are being used up at an alarming rate. To meet our demands we are now searching for new sources of energy. One of these new sources of energy is solar energy which will assume increasing importance. It is free but means must be developed to use it economically. Research is actively under way to reduce the storage cost of this low intensity energy and for the design of economical systems. The purpose of this Institute is to provide an international forum for the dissemination of information on solar energy utilization: fundamentals and applications in industry. This meeting is primarily a high level teaching activity. The subject is treated in considerable depth by lecturers eminent in their field. The other participants include scientists, engineers, and senior graduate students who themselves are involved in a similar research and who wish to learn more about current developments, as well as scientists from other areas who are planning to research on solar energy. The lectures are supplemented by informal discussions designed to encourage the free and critical exchange of ideas. A limited number of contributions are also included. This volume contains both basic and applied information contributed during the Institute. The editors appreciate the cooperation of Martinus Nijhoff Publishezsin making the proceedings widely available.
Download or read book Phase Change Materials and Their Applications written by Mohsen Mhadhbi and published by BoD – Books on Demand. This book was released on 2018-08-01 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today, the application of phase change materials (PCMs) has developed in different industries, including the solar cooling and solar power plants, photovoltaic electricity systems, the space industry, waste heat recovery systems, preservation of food and pharmaceutical products, and domestic hot water. PCMs use the principle of latent heat thermal storage to absorb energy in large quantities when there is a surplus and release it when there is a deficit. This promising technology has already been successfully implemented in many construction projects. The aim of this book is to assist the scientists and to provide the reader with a comprehensive overview of the properties that characterize the phase change materials from theoretical and experimental perspectives with a focus on their technological applications. The present status and future perspectives of phase change material are discussed.
Download or read book Efficient Phase Change Materials written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: HEATS Project: USF is developing low-cost, high-temperature phase-change materials (PCMs) for use in thermal energy storage systems. Heat storage materials are critical to the energy storage process. In solar thermal storage systems, heat can be stored in these materials during the day and released at night--when the sun is not out--to drive a turbine and produce electricity. In nuclear storage systems, heat can be stored in these materials at night and released to produce electricity during daytime peak-demand hours. Most PCMs do not conduct heat very well. Using an innovative, electroless encapsulation technique, USF is enhancing the heat transfer capability of its PCMs. The inner walls of the capsules will be lined with a corrosion-resistant, high-infrared emissivity coating, and the absorptivity of the PCM will be controlled with the addition of nano-sized particles. USF's PCMs remain stable at temperatures from 600 to 1,000°C and can be used for solar thermal power storage, nuclear thermal power storage, and other applications.
Download or read book Recent Advancements in Materials and Systems for Thermal Energy Storage written by Andrea Frazzica and published by Springer. This book was released on 2018-08-28 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the latest advances in thermal energy storage development at both the materials and systems level. It covers various fields of application, including domestic, industrial and transport, as well as diverse technologies, such as sensible, latent and thermochemical. The contributors introduce readers to the main performance indicators for thermal storage systems, and discuss thermal energy storage (TES) technologies that can be used to improve the efficiency of energy systems and increase the share of renewable energy sources in numerous fields of application. In addition to the latest advances, the authors discuss the development and characterization of advanced materials and systems for sensible, latent and thermochemical TES, as well as the TES market and practical applications. They also report on and assess the feasibility of uniform characterization protocols and main performance indicators, compared to previous attempts to be found in the literature. The book will help to increase awareness of thermal energy storage technologies in both the academic and industrial sectors, while also providing experts new tools to achieve a uniform approach to thermal energy storage characterization methods. It will also be of interest to all students and researchers seeking an introduction to recent innovations in TES technologies.
Download or read book Thermal Energy Storage for Solar Applications written by Charles E. Wyman and published by . This book was released on 1979 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Energy Storage written by Hafiz Muhammad Ali and published by Springer Nature. This book was released on 2021-04-12 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers various aspects of thermal energy storage. It looks at storage methods for thermal energy and reviews the various materials that store thermal energy and goes on to propose advanced materials that store energy better than conventional materials. The book also presents various thermophysical properties of advanced materials and the role of thermal energy storage in different applications such as buildings, solar energy, seawater desalination and cooling devices. The advanced energy storage materials have massive impact on heat transfer as compared to conventional energy storage materials. A concise discussion regarding current status, leading groups, journals and the countries working on advanced energy storage materials has also been provided. This book is useful to researchers, professionals and policymakers alike.
