Download or read book Circuit Techniques for High speed Serial and Backplane Signaling written by Marcus Henricus Van Ierssel and published by . This book was released on 2007 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: Second, this thesis proposes a new adaptation technique for a 4-PAM decision-feedback equalizer (DFE). The DFE adapts to the channel impulse response by observing an intermittent calibration sequence sent across the channel. Uninterrupted signaling is maintained across a parallel bus by providing an additional channel and using multiplexers to reroute the signals of the channel being calibrated. Using the intermittent calibration sequence, instead of the conventional LMS adaptation technique, removes the need to generate an error signal, eliminating the associated analog blocks. Also presented is a novel method of using the DFE adaptation circuits to extract the system's pulse response. The complete transceiver is implemented in a 0.18 mum CMOS process. This thesis describes three contributions towards the design and modeling of high-speed serial and backplane signaling systems. Specifically, these contributions address the issues of fitter and intersymbol interference in clock and data recovery circuits. First, this thesis proposes the modeling of jitter in clock and data recovery (CDR) systems using an event-driven model that accurately includes the effects of power-supply noise, the finite bandwidth in the phase-detector's front-end sampler, and ISI in the system's channel. These continuous-time jitter sources are captured in the model through their discrete-time influence on sample based phase-detectors. Modeling parameters for these disturbances are directly extracted from the circuit implementation. The jitter predicted by the event-driven model, implemented in Simulink, is within 12% of that predicted by an Hspice simulation, but with a simulation speed that is 1800 times higher. Finally, a hybrid CDR is proposed that increases the jitter tolerance of a phase-tracking CDR by a factor of 32 at frequencies below its loop filter's bandwidth, while maintaining the high-frequency jitter tolerance of a 5x blind-oversampling CDR. Measured data from a 0.11 um CMOS testchip at 2.4Gb/s confirm a 200UI peak-to-peak jitter tolerance for a 200kHz jitter. The testchip is operational from 1.9Gb/s to 3.5Gb/s and consumes 115mW at 2.4Gb/s.

Download or read book Design of High speed Communication Circuits written by Ramesh Harjani and published by World Scientific. This book was released on 2006 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: MOS technology has rapidly become the de facto standard for mixed-signal integrated circuit design due to the high levels of integration possible as device geometries shrink to nanometer scales. The reduction in feature size means that the number of transistor and clock speeds have increased significantly. In fact, current day microprocessors contain hundreds of millions of transistors operating at multiple gigahertz. Furthermore, this reduction in feature size also has a significant impact on mixed-signal circuits. Due to the higher levels of integration, the majority of ASICs possesses some analog components. It has now become nearly mandatory to integrate both analog and digital circuits on the same substrate due to cost and power constraints. This book presents some of the newer problems and opportunities offered by the small device geometries and the high levels of integration that is now possible. The aim of this book is to summarize some of the most critical aspects of high-speed analog/RF communications circuits. Attention is focused on the impact of scaling, substrate noise, data converters, RF and wireless communication circuits and wireline communication circuits, including high-speed I/O. Contents: Achieving Analog Accuracy in Nanometer CMOS (M P Flynn et al.); Self-Induced Noise in Integrated Circuits (R Gharpurey & S Naraghi); High-Speed Oversampling Analog-to-Digital Converters (A Gharbiya et al.); Designing LC VCOs Using Capacitive Degeneration Techniques (B Jung & R Harjani); Fully Integrated Frequency Synthesizers: A Tutorial (S T Moon et al.); Recent Advances and Design Trends in CMOS Radio Frequency Integrated Circuits (D J Allstot et al.); Equalizers for High-Speed Serial Links (P K Hanumolu et al.); Low-Power, Parallel Interface with Continuous-Time Adaptive Passive Equalizer and Crosstalk Cancellation (C P Yue et al.). Readership: Technologists, scientists, and engineers in the field of high-speed communication circuits. It can also be used as a textbook for graduate and advanced undergraduate courses.

Download or read book High Speed Serdes Devices and Applications written by David Robert Stauffer and published by Springer Science & Business Media. This book was released on 2008-12-19 with total page 495 pages. Available in PDF, EPUB and Kindle. Book excerpt: The simplest method of transferring data through the inputs or outputs of a silicon chip is to directly connect each bit of the datapath from one chip to the next chip. Once upon a time this was an acceptable approach. However, one aspect (and perhaps the only aspect) of chip design which has not changed during the career of the authors is Moore’s Law, which has dictated substantial increases in the number of circuits that can be manufactured on a chip. The pin densities of chip packaging technologies have not increased at the same pace as has silicon density, and this has led to a prevalence of High Speed Serdes (HSS) devices as an inherent part of almost any chip design. HSS devices are the dominant form of input/output for many (if not most) high-integration chips, moving serial data between chips at speeds up to 10 Gbps and beyond. Chip designers with a background in digital logic design tend to view HSS devices as simply complex digital input/output cells. This view ignores the complexity associated with serially moving billions of bits of data per second. At these data rates, the assumptions associated with digital signals break down and analog factors demand consideration. The chip designer who oversimplifies the problem does so at his or her own peril.

Download or read book High Speed Signaling written by Kyung Suk (Dan) Oh and published by Prentice Hall. This book was released on 2011-10-07 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: New System-Level Techniques for Optimizing Signal/Power Integrity in High-Speed Interfaces--from Pioneering Innovators at Rambus, Stanford, Berkeley, and MIT As data communication rates accelerate well into the multi-gigahertz range, ensuring signal integrity both on- and off-chip has become crucial. Signal integrity can no longer be addressed solely through improvements in package or board-level design: Diverse engineering teams must work together closely from the earliest design stages to identify the best system-level solutions. In High-Speed Signaling, several of the field’s most respected practitioners and researchers introduce cutting-edge modeling, simulation, and optimization techniques for meeting this challenge. Edited by pioneering experts Drs. Dan Oh and Chuck Yuan, these contributors explain why noise and jitter are no longer separable, demonstrate how to model their increasingly complex interactions, and thoroughly introduce a new simulation methodology for predicting link-level performance with unprecedented accuracy. The authors address signal integrity from architecture through high-volume production, thoroughly discussing design, implementation, and verification. Coverage includes New advances in passive-channel modeling, power-supply noise and jitter modeling, and system margin prediction Methodologies for balancing system voltage and timing budgets to improve system robustness in high-volume manufacturing Practical, stable formulae for converting key network parameters Improved solutions for difficult problems in the broadband modeling of interconnects Equalization techniques for optimizing channel performance Important new insights into the relationships between jitter and clocking topologies New on-chip measurement techniques for in-situ link performance testing Trends and future directions in signal integrity engineering High-Speed Signaling thoroughly introduces new techniques pioneered at Rambus and other leading high-tech companies and universities: approaches that have never before been presented with this much practical detail. It will be invaluable to everyone concerned with signal integrity, including signal and power integrity engineers, high-speed I/O circuit designers, and system-level board design engineers.

Download or read book Design Of High speed Communication Circuits written by Ramesh Harjani and published by World Scientific. This book was released on 2006-01-17 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: MOS technology has rapidly become the de facto standard for mixed-signal integrated circuit design due to the high levels of integration possible as device geometries shrink to nanometer scales. The reduction in feature size means that the number of transistor and clock speeds have increased significantly. In fact, current day microprocessors contain hundreds of millions of transistors operating at multiple gigahertz. Furthermore, this reduction in feature size also has a significant impact on mixed-signal circuits. Due to the higher levels of integration, the majority of ASICs possesses some analog components. It has now become nearly mandatory to integrate both analog and digital circuits on the same substrate due to cost and power constraints. This book presents some of the newer problems and opportunities offered by the small device geometries and the high levels of integration that is now possible.The aim of this book is to summarize some of the most critical aspects of high-speed analog/RF communications circuits. Attention is focused on the impact of scaling, substrate noise, data converters, RF and wireless communication circuits and wireline communication circuits, including high-speed I/O.

Download or read book High speed Circuit Board Signal Integrity written by Stephen C. Thierauf and published by Artech House. This book was released on 2004 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: As circuit boards are increasingly required to transmit signals at higher and higher speeds, signal and power integrity become increasingly crucial. Rules of thumb that you have used over and over again to prevent signal loss no longer apply to these new, high-speed, high-density circuit designs. This leading-edge circuit design resource offers you the knowledge needed to quickly pinpoint transmission problems that can compromise your entire circuit design. Discussing both design and debug issues at gigabit per second data rates, the book serves as a practical reference for your projects involving high-speed serial signaling on printed wiring boards.

Download or read book High Speed Circuit Board Signal Integrity Second Edition written by Stephen C. Thierauf and published by Artech House. This book was released on 2017-04-30 with total page 321 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thoroughly updated leading-edge circuit design resource offers the knowledge needed to quickly pinpoint transmission problems that can compromise the entire circuit design. This new edition demonstrates how to apply EM theory to solve signal integrity problems with a practical application-oriented approach. Discussing both design and debug issues at gigabit per second data rates, the book serves as a practical reference for projects involving high-speed serial signaling on printed wiring boards. Step-by-step, this book goes from reviewing the essentials of linear circuit theory, to examining practical issues of pulse propagation along lossless and lossy transmission lines. It provides detailed guidelines for crosstalk, attenuation, power supply decoupling, and layer stackup tradeoffs (including pad/antipad tradeoffs). Other key topics include the construction of etched conductors, analysis of return paths and split planes, microstrip and stripline characteristics, and SMT capacitors. Filled with on-the-job-proven examples, this hands-on reference is the book that engineers can turn to time and again to design out and troubleshoot circuit signal loss and impedance problems.

Download or read book High Performance Multi Channel High Speed I O Circuits written by Taehyoun Oh and published by Springer Science & Business Media. This book was released on 2013-09-07 with total page 91 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes design techniques that can be used to mitigate crosstalk in high-speed I/O circuits. The focus of the book is in developing compact and low power integrated circuits for crosstalk cancellation, inter-symbol interference (ISI) mitigation and improved bit error rates (BER) at higher speeds. This book is one of the first to discuss in detail the problem of crosstalk and ISI mitigation encountered as data rates have continued beyond 10Gb/s. Readers will learn to avoid the data performance cliff, with circuits and design techniques described for novel, low power crosstalk cancellation methods that are easily combined with current ISI mitigation architectures.

Download or read book Handbook of Signal Processing Systems written by Shuvra S. Bhattacharyya and published by Springer Science & Business Media. This book was released on 2013-06-20 with total page 1395 pages. Available in PDF, EPUB and Kindle. Book excerpt: Handbook of Signal Processing Systems is organized in three parts. The first part motivates representative applications that drive and apply state-of-the art methods for design and implementation of signal processing systems; the second part discusses architectures for implementing these applications; the third part focuses on compilers and simulation tools, describes models of computation and their associated design tools and methodologies. This handbook is an essential tool for professionals in many fields and researchers of all levels.

Download or read book CMOSET 2010 Circuits Track Presentation Slides written by CMOS Emerging Technologies Research and published by CMOS Emerging Technologies. This book was released on with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Analog Circuit Design written by Michiel Steyaert and published by Springer Science & Business Media. This book was released on 2008-09-19 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog Circuit Design contains the contribution of 18 tutorials of the 17th workshop on Advances in Analog Circuit Design. Each part discusses a specific to-date topic on new and valuable design ideas in the area of analog circuit design. Each part is presented by six experts in that field and state of the art information is shared and overviewed. This book is number 17 in this successful series of Analog Circuit Design.

Download or read book Coupled Data Communication Techniques for High Performance and Low Power Computing written by Ron Ho and published by Springer Science & Business Media. This book was released on 2010-06-03 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wafer-scale integration has long been the dream of system designers. Instead of chopping a wafer into a few hundred or a few thousand chips, one would just connect the circuits on the entire wafer. What an enormous capability wafer-scale integration would offer: all those millions of circuits connected by high-speed on-chip wires. Unfortunately, the best known optical systems can provide suitably ?ne resolution only over an area much smaller than a whole wafer. There is no known way to pattern a whole wafer with transistors and wires small enough for modern circuits. Statistical defects present a ?rmer barrier to wafer-scale integration. Flaws appear regularly in integrated circuits; the larger the circuit area, the more probable there is a ?aw. If such ?aws were the result only of dust one might reduce their numbers, but ?aws are also the inevitable result of small scale. Each feature on a modern integrated circuit is carved out by only a small number of photons in the lithographic process. Each transistor gets its electrical properties from only a small number of impurity atoms in its tiny area. Inevitably, the quantized nature of light and the atomic nature of matter produce statistical variations in both the number of photons de?ning each tiny shape and the number of atoms providing the electrical behavior of tiny transistors. No known way exists to eliminate such statistical variation, nor may any be possible.

Download or read book High speed Optical Transceivers Integrated Circuits Designs And Optical Devices Techniques written by Yuyu Liu and published by World Scientific. This book was released on 2006-03-09 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the unique advantages and large inherent transmission capacity of optical fiber communication systems. The long-term and high-risk research challenges of optical transceivers are analyzed with a view to sustaining the seemingly insatiable demand for bandwidth. A broad coverage of topics relating to the design of high-speed optical devices and integrated circuits, oriented to low power, low cost, and small area, is discussed.Written by specialists with many years of research and engineering experience in the field of optical fiber communication, this book is essential for an audience dedicated to the development of integrated electronic systems for optical communication applications. It can also be used as a supplementary text for graduate courses on optical transceiver IC design.

Download or read book High Frequency Communication and Sensing written by Ahmet Tekin and published by CRC Press. This book was released on 2018-09-03 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: High Frequency Communication and Sensing: Traveling-Wave Techniques introduces novel traveling wave circuit techniques to boost the performance of high-speed circuits in standard low-cost production technologies, like complementary metal oxide semiconductor (CMOS). A valuable resource for experienced analog/radio frequency (RF) circuit designers as well as undergraduate-level microelectronics researchers, this book: Explains the basics of high-speed signaling, such as transmission lines, distributed signaling, impedance matching, and other common practical RF background material Promotes a dual-loop coupled traveling wave oscillator topology, the trigger mode distributed wave oscillator, as a high-frequency multiphase signal source Introduces a force-based starter mechanism for dual-loop, even-symmetry, multiphase traveling wave oscillators, presenting a single-loop version as a force mode distributed wave antenna (FMDWA) Describes higher-frequency, passive inductive, and quarter-wave-length-based pumped distributed wave oscillators (PDWOs) Examines phased-array transceiver architectures and front-end circuits in detail, along with distributed oscillator topologies Devotes a chapter to THz sensing, illustrating a unique method of traveling wave frequency multiplication and power combining Discusses various data converter topologies, such as digital-to-analog converters (DACs), analog-to-digital converters (ADCs), and GHz-bandwidth sigma-delta modulators Covers critical circuits including phase rotators and interpolators, phase shifters, phase-locked loops (PLLs), delay-locked loops (DLLs), and more It is a significantly challenging task to generate and distribute high-speed clocks. Multiphase low-speed clocks with sharp transition are proposed to be a better option to accommodate the desired timing resolution. High Frequency Communication and Sensing: Traveling-Wave Techniques provides new horizons in the quest for greater speed and performance.

Download or read book High Frequency Communication and Sensing written by Ahmet Tekin and published by CRC Press. This book was released on 2018-09-03 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: High Frequency Communication and Sensing: Traveling-Wave Techniques introduces novel traveling wave circuit techniques to boost the performance of high-speed circuits in standard low-cost production technologies, like complementary metal oxide semiconductor (CMOS). A valuable resource for experienced analog/radio frequency (RF) circuit designers as well as undergraduate-level microelectronics researchers, this book: Explains the basics of high-speed signaling, such as transmission lines, distributed signaling, impedance matching, and other common practical RF background material Promotes a dual-loop coupled traveling wave oscillator topology, the trigger mode distributed wave oscillator, as a high-frequency multiphase signal source Introduces a force-based starter mechanism for dual-loop, even-symmetry, multiphase traveling wave oscillators, presenting a single-loop version as a force mode distributed wave antenna (FMDWA) Describes higher-frequency, passive inductive, and quarter-wave-length-based pumped distributed wave oscillators (PDWOs) Examines phased-array transceiver architectures and front-end circuits in detail, along with distributed oscillator topologies Devotes a chapter to THz sensing, illustrating a unique method of traveling wave frequency multiplication and power combining Discusses various data converter topologies, such as digital-to-analog converters (DACs), analog-to-digital converters (ADCs), and GHz-bandwidth sigma-delta modulators Covers critical circuits including phase rotators and interpolators, phase shifters, phase-locked loops (PLLs), delay-locked loops (DLLs), and more It is a significantly challenging task to generate and distribute high-speed clocks. Multiphase low-speed clocks with sharp transition are proposed to be a better option to accommodate the desired timing resolution. High Frequency Communication and Sensing: Traveling-Wave Techniques provides new horizons in the quest for greater speed and performance.

Download or read book High Speed Serial Link written by Moises Cases and published by Wiley. This book was released on 2025-07-08 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the high speed serial (HSS) system design as it relates to electronic system design engineers, electronic packaging engineers and to signal and power integrity engineers. The book covers basic concepts input/output (I/O) signalling including trends, protocols, basic signal and power integrity concepts, an overview of current HSS system design and specifications, channel loss components, typical HSS topologies, electrical modelling methodology and techniques, link simulation techniques, link analysis and optimization, and link measurement parameters and techniques. It includes practical design examples and recommendations, as well as typical measurement parameter values and failure analysis.

Download or read book High speed Integrated Circuit Technology written by Mark J. W. Rodwell and published by World Scientific. This book was released on 2001 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the state of the art of very high speed digital integrated circuits. Commercial applications are in fiber optic transmission systems operating at 10, 40, and 100 Gb/s, while the military application is ADCs and DACs for microwave radar. The book contains detailed descriptions of the design, fabrication, and performance of wideband Si/SiGe-, GaAs-, and InP-based bipolar transistors. The analysis, design, and performance of high speed CMOS, silicon bipolar, and III-V digital ICs are presented in detail, with emphasis on application in optical fiber transmission and mixed signal ICs. The underlying physics and circuit design of rapid single flux quantum (RSFQ) superconducting logic circuits are reviewed, and there is extensive coverage of recent integrated circuit results in this technology. Contents: Preface (M J W Rodwell); High-Speed and High-Data-Bandwidth Transmitter and Receiver for Multi-Channel Serial Data Communication with CMOS Technology (M Fukaishi et al.); High-Performance Si and SiGe Bipolar Technologies and Circuits (M Wurzer et al.); Self-Aligned Si BJT/SiGe HBT Technology and Its Application to High-Speed Circuits (K Washio); Small-Scale InGaP/GaAs Heterojunction Bipolar Transistors for High-Speed and Low-Power Integrated-Circuit Applications (T Oka et al.); Prospects of InP-Based IC Technologies for 100-Gbit/S-Class Lightwave Communications Systems (T Enoki et al.); Scaling of InGaAs/InAlAs HBTs for High Speed Mixed-Signal and mm-Wave ICs (M J W Rodwell); Progress Toward 100 GHz Logic in InP HBT IC Technology (C H Fields et al.); Cantilevered Base InP DHBT for High Speed Digital Applications (A L Gutierrez-Aitken et al.); RSFQ Technology: Physics and Devices (P Bunyk et al.); RSFQ Technology: Circuits and Systems (D K Brock). Readership: Researchers, industrialists and academics in electrical and electronic engineering.