Download or read book Characterisation and Development of Nanostructured Ultrahigh Strength and Ductile Bainitic Steels written by Mohamed Sherif and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of the present work was to characterise and further develop a novel nanostructured type of bainitic steel. Three chemical compositions were considered with different concentrations of Al and Co. The addition of Al and Co is believed to be necessary to produce the desired nanostructure at very low temperatures within a reasonable transformation time. An overview of the mechanical performance of fully bainitic steels vs other steel systems is presented in Chapter 1. An introduction to metallurgical concepts regarding the design and performance of bainite steels is presented in Chapters 1 and 2. Chapter 2 focuses on the design concepts by which the steel chemical composition was optimised, primarily on the basis of cost and the avoidance of carbide precipitation. Chapter 3 deals with the evolution of the microstructure during uniaxial tension, studied using X-ray diffraction. The effect of tempering deformed and undeformed structures, and heating to high temperatures, have also been investigated. In this context, data on bainite-containing steels in the literature are found to be rather limited. Chapter 4 is a comprehensive assessment of the mechanical behaviour of the steels subjected to a variety of processing routes. It is demonstrated that it is possible to outperform current commercially available steels. The microstructural behaviour of strain-aged and as-transformed steels during uniaxial tension studied using in situ neutron diffraction is described in Chapter 5. The evolution of texture with plastic deformation was confirmed as previously observed using conventional X-ray analysis. Evidence regarding the presence of two populations of carbon-depleted and carbon-rich austenite and their response to strain, grain rotation, anisotropy, stress partitioning between phases and the lack of work-hardening to overcome the onset of necking are presented.
Download or read book Bainite in Steels written by H.K.D.H. Bhadeshia and published by CRC Press. This book was released on 2019-04-15 with total page 616 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the third edition of the book, much expanded to include and incorporate important developments in the subject over the last fifteen years. The book represents a comprehensive treatise on all aspects of the bainite transformation, from the choreography of atoms during the phase change to length scales that are typical of engineering applications. The alloy design that emerges from this explains the role of solute additions, and the pernicious effects of impurities such as hydrogen. The picture presented is self-consistent and therefore is able to guide the reader on the exploitation of theory to the design of some of the most exciting steels, including the world’s first bulk nanostructured metal.
Download or read book Handbook of Mechanical Nanostructuring written by Mahmood Aliofkhazraei and published by John Wiley & Sons. This book was released on 2016-05-02 with total page 816 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing in-depth information on how to obtain high-performance materials by controlling their nanostructures, this ready reference covers both the bottom-up and the top-down approaches to the synthesis and processing of nanostructured materials. The focus is on advanced methods of mechanical nanostructuring such as severe plastic deformation, including high pressure torsion, equal channel angular processing, cyclic extrusion compression, accumulative roll bonding, and surface mechanical attrition treatment. As such, the contents are inherently application-oriented, with the methods presented able to be easily integrated into existing production processes. In addition, the structure-property relationships and ways of influencing the nanostructure in order to exhibit a desired functionality are reviewed in detail. The whole is rounded off by a look at future directions, followed by an overview of applications in various fields of structural and mechanical engineering. With its solutions for successful processing of complex-shaped workpieces and large-scale specimens with desired properties, this is an indispensable tool for purposeful materials design.
Download or read book Phase Transformations in Steels written by Elena Pereloma and published by Elsevier. This book was released on 2012-05-11 with total page 673 pages. Available in PDF, EPUB and Kindle. Book excerpt: The processing-microstructure-property relationships in steels continue to present challenges to researchers because of the complexity of phase transformation reactions and the wide spectrum of microstructures and properties achievable. This major two-volume work summarises the current state of research on phase transformations in steels and its implications for the emergence of new steels with enhanced engineering properties.Volume 2 reviews current research on diffusionless transformations and phase transformations in high strength steels, as well as advances in modelling and analytical techniques which underpin this research. Chapters in part one discuss the crystallography and kinetics of martensite transformations, the morphology, substructure and tempering of martensite as well as shape memory in ferrous alloys. Part two summarises research on phase transformations in high strength low alloy (HSLA) steels, transformation induced plasticity (TRIP)-assisted multiphase steels, quenched and partitioned steels, advanced nanostructured bainitic steels, high manganese twinning induced plasticity (TWIP) and maraging steels. The final two parts of the book review advances in modelling and the use of advanced analytical techniques to improve our understanding of phase transformations in steels.With its distinguished editors and distinguished international team of contributors, the two volumes of Phase transformations in steels is a standard reference for all those researching the properties of steel and developing new steels in such areas as automotive engineering, oil and gas and energy production. Alongside its companion volume, this major two-volume work summarises the current state of research on phase transformations in steels Reviews research on diffusionless transformations and phase transformations in high strength steels Examines advances in modelling and the use of advanced analytical techniques to improve understanding of phase transformations in steels
Download or read book Comprehensive Materials Processing written by and published by Newnes. This book was released on 2014-04-07 with total page 5485 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive Materials Processing, Thirteen Volume Set provides students and professionals with a one-stop resource consolidating and enhancing the literature of the materials processing and manufacturing universe. It provides authoritative analysis of all processes, technologies, and techniques for converting industrial materials from a raw state into finished parts or products. Assisting scientists and engineers in the selection, design, and use of materials, whether in the lab or in industry, it matches the adaptive complexity of emergent materials and processing technologies. Extensive traditional article-level academic discussion of core theories and applications is supplemented by applied case studies and advanced multimedia features. Coverage encompasses the general categories of solidification, powder, deposition, and deformation processing, and includes discussion on plant and tool design, analysis and characterization of processing techniques, high-temperatures studies, and the influence of process scale on component characteristics and behavior. Authored and reviewed by world-class academic and industrial specialists in each subject field Practical tools such as integrated case studies, user-defined process schemata, and multimedia modeling and functionality Maximizes research efficiency by collating the most important and established information in one place with integrated applets linking to relevant outside sources
Download or read book Encyclopedia of Iron Steel and Their Alloys Online Version written by George E. Totten and published by CRC Press. This book was released on 2016-01-06 with total page 3918 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first of many important works featured in CRC Press’ Metals and Alloys Encyclopedia Collection, the Encyclopedia of Iron, Steel, and Their Alloys covers all the fundamental, theoretical, and application-related aspects of the metallurgical science, engineering, and technology of iron, steel, and their alloys. This Five-Volume Set addresses topics such as extractive metallurgy, powder metallurgy and processing, physical metallurgy, production engineering, corrosion engineering, thermal processing, metalworking, welding, iron- and steelmaking, heat treating, rolling, casting, hot and cold forming, surface finishing and coating, crystallography, metallography, computational metallurgy, metal-matrix composites, intermetallics, nano- and micro-structured metals and alloys, nano- and micro-alloying effects, special steels, and mining. A valuable reference for materials scientists and engineers, chemists, manufacturers, miners, researchers, and students, this must-have encyclopedia: Provides extensive coverage of properties and recommended practices Includes a wealth of helpful charts, nomograms, and figures Contains cross referencing for quick and easy search Each entry is written by a subject-matter expert and reviewed by an international panel of renowned researchers from academia, government, and industry. Also Available Online This Taylor & Francis encyclopedia is also available through online subscription, offering a variety of extra benefits for researchers, students, and librarians, including: Citation tracking and alerts Active reference linking Saved searches and marked lists HTML and PDF format options Contact Taylor and Francis for more information or to inquire about subscription options and print/online combination packages. US: (Tel) 1.888.318.2367; (E-mail) [email protected] International: (Tel) +44 (0) 20 7017 6062; (E-mail) [email protected]
Download or read book Bainite and Martensite written by Carlos Garcia-Mateo and published by MDPI. This book was released on 2020-05-27 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: The microstructures of both martensite and bainite, although sharing some common features, depict a plethora of subtle differences that made them unique when studied in further detail. Tailoring the final properties of a microstructure based on one or the other as well as in combination with others and exploring more sophisticated concepts, such as Q&P and nanostructured bainite, are the topics which are the focus of research around the world. In understanding the key microstructural parameters controlling the final properties as well as definition of adequate process parameters to attain the desired microstructures requires that a proper understanding of the mechanism ruling their transformation and a detailed characterization first be acheived. The development of new and powerful scientific techniques and equipment (EBSD, APT, HRTEM, etc.) allow us to gain fundamental insights that help to establish some of the principles by which those microstructures are known. The developments accompanying such findings lead to further developments and intensive research providing the required metallurgical support.
Download or read book New Advanced Ultra High Strength Bainitic Steels Ductility and Formability DUCTAFORM written by and published by . This book was released on 2013 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main objective of this proposal is to develop AHSS both hot rolled and annealed cold rolled bainitic steels with an optimal ductility and work hardening comparable to drawing steels, and/or keeping a suitable bending and stretching behaviour. In addition, forming processes such as roll-forming and hardening, and press-hardening were optimised to achieve a carbide free bainitic microstructure in final products such as structural safety components in the car body i.e. A-beam, roof-beams, car bumpers and side impact beams. Hot rolling of carbide free bainitic steels with 1100 MPa of yield strength and high toughness (KV(-40oC)>30 J) was proved to be challenging. Apart of a high carbon content (̃0.3wt.%), chemical composition requires of a high manganese content (̃2wt.%), which leads to a high risk of banding. By contrast, annealed cold rolled bainitic steels designed for continuous annealing line achieved far higher uniform elongation, better stretching ability and formability than that in DP980 and Martensitic 1400 steels considering the same range of ultimate tensile strengths. Finally, roll-forming simulations of bainitic cold rolled steels obtained by interrupted quenching and salt bath at different temperatures showed an excellent formability without crack formation in comparison to martensitic 22MnB5 reference steel. Likewise, press-hardening trials of hat shaped profiles using a novel quench and partitioning post heat treatment of cold rolled designed steels showed promising tensile results in comparison to same commercial 22MnB5 profiles.
Download or read book Index to Theses with Abstracts Accepted for Higher Degrees by the Universities of Great Britain and Ireland and the Council for National Academic Awards written by and published by . This book was released on 2006 with total page 648 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanostructured Metals and Alloys written by S H Whang and published by Elsevier. This book was released on 2011-03-22 with total page 840 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile strength, fatigue strength and ductility are important properties of nanostructured metallic materials, which make them suitable for use in applications where strength or strength-to-weight ratios are important. Nanostructured metals and alloys reviews the latest technologies used for production of these materials, as well as recent advances in research into their structure and mechanical properties. One of the most important issues facing nanostructured metals and alloys is how to produce them. Part one describes the different methods used to process bulk nanostructured metals and alloys, including chapters on severe plastic deformation, mechanical alloying and electrodeposition among others. Part two concentrates on the microstructure and properties of nanostructured metals, with chapters studying deformation structures such as twins, microstructure of ferrous alloys by equal channel angular processing, and characteristic structures of nanostructured metals prepared by plastic deformation. In part three, the mechanical properties of nanostructured metals and alloys are discussed, with chapters on such topics as strengthening mechanisms, nanostructured metals based on molecular dynamics computer simulations, and surface deformation. Part four focuses on existing and developing applications of nanostructured metals and alloys, covering topics such as nanostructured steel for automotives, steel sheet and nanostructured coatings by spraying. With its distinguished editor and international team of contributors, Nanostructured metals and alloys is a standard reference for manufacturers of metal components, as well as those with an academic research interest in metals and materials with enhanced properties.
Download or read book Advanced Steels written by Yuqing Weng and published by Springer Science & Business Media. This book was released on 2011-04-14 with total page 495 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Advanced Steels: The Recent Scenario in Steel Science and Technology" contains more than 50 articles selected from the proceedings of the International Conference on Advanced Steels (ICAS) held during 9-11, Nov, 2010 in Guilin, China. This book covers almost all important aspects of steels from physical metallurgy, steel grades, processing and fabrication, simulation, to properties and applications. The book is intended for researchers and postgraduate students in the field of steels, metallurgy and materials science. Prof. Yuqing Weng is an academician of Chinese Academy of Engineering and the president of The Chinese Society for Metals. Prof. Han Dong is the vice president of Central Iron & Steel Research Institute and the director of National Engineering Research Center of Advanced Steel Technology, China. Prof. Yong Gan is an academician of Chinese Academy of Engineering, the vice president of Chinese Academy of Engineering and the president of Central Iron & Steel Research Institute, China.
Download or read book Bainite in Steels written by H.K.D.H. Bhadeshia and published by CRC Press. This book was released on 2019-04-15 with total page 910 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the third edition of the book, much expanded to include and incorporate important developments in the subject over the last fifteen years. The book represents a comprehensive treatise on all aspects of the bainite transformation, from the choreography of atoms during the phase change to length scales that are typical of engineering applications. The alloy design that emerges from this explains the role of solute additions, and the pernicious effects of impurities such as hydrogen. The picture presented is self-consistent and therefore is able to guide the reader on the exploitation of theory to the design of some of the most exciting steels, including the world’s first bulk nanostructured metal.
Download or read book Additive Manufacturing AM of Metallic Alloys written by Flaviana Calignano and published by . This book was released on 2020-09-16 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: The introduction of metal AM processes in such industrial sectors as the aerospace, automotive, defense, jewelry, medical and tool-making fields, has led to a significant reduction in waste material and in the lead times of the components, innovative designs with higher strength, lower weight, and fewer potential failure points from joining features. This Special Issue on "Additive Manufacturing (AM) of Metallic Alloys" contains a mixture of review articles and original contributions on some problems that limit the wider uptake and exploitation of metals in AM.
Download or read book Bainite in Steels written by Harshad Kumar Dharamshi Hansraj Bhadeshia and published by Maney Publishing. This book was released on 2001 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of this modern classic encompasses the latest research, which sees bainitic alloys at the forefront of a new wave of "designed" steels. Contents include: Nomenclature; Introduction; Bainitic Ferrite; Carbide Precipitation; Tempering of Bainite; Thermodynamics; Kinetics; Upper and Lower Bainite; Stress and Strain Effects; Reverse Transformation from Bainite to Austenite; Acicular Ferrite; Other Morphologies of Bainite; Mechanical Properties; Modern Bainitic Alloys;Other Aspects; The Transformation of Steel.
Download or read book Maraging Steels written by W Sha and published by Elsevier. This book was released on 2009-10-26 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt: Maraging steels are high-strength steels combined with good toughness. They are used particularly in aerospace and tooling applications. Maraging refers to the ageing of martensite, a hard microstructure commonly found in steels.Maraging steels: modelling of microstructure, properties and applications covers the following topics: Introduction to maraging steels; Microstructure of maraging steels; Mechanical properties of maraging steels; Thermodynamic calculations for quantifying the phase fraction and element partition in maraging systems and precipitation hardening steels; Quantification of phase transformation kinetics in maraging steels; Quantification of age hardening in maraging steels; Maraging steels and overageing; Precipitation hardening stainless steel; Applications of artificial neural network on modelling maraging steel properties.With its distinguished authors, Maraging steels: modelling of microstructure, properties and applications is a standard reference for industry and researchers concerned with maraging steels and modelling as well as users of maraging steels in the aerospace and tooling sectors. The book includes both conventional maraging steels and precipitation hardened (PH) stainless steels. Provides an overview of maraging steels including microstructure and mechanical properties Reviews thermodynamic calculations for quantifying the phase fraction and element partition in maraging steels Includes chapters on the quantification of phase transformation kinetics and age hardening in maraging steels
Download or read book Introduction to the Physical Metallurgy of Welding written by Kenneth Easterling and published by Elsevier. This book was released on 2013-09-17 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to the Physical Metallurgy of Welding deals primarily with the welding of steels, which reflects the larger volume of literature on this material; however, many of the principles discussed can also be applied to other alloys. The book is divided into four chapters, in which the middle two deal with the microstructure and properties of the welded joint, such as the weld metal and the heat-affected zone. The first chapter is designed to provide a wider introduction to the many process variables of fusion welding, particularly those that may influence microstructure and properties, while the final chapter is concerned with cracking and fracture in welds. A comprehensive case study of the Alexander Kielland North Sea accommodation platform disaster is also discussed at the end. The text is written for undergraduate or postgraduate courses in departments of metallurgy, materials science, or engineering materials. The book will also serve as a useful revision text for engineers concerned with welding problems in industry.
Download or read book Advanced High Strength Steels written by Mahmoud Y. Demeri and published by ASM International. This book was released on 2013-08-01 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: Examines the types, microstructures and attributes of AHSSAlso reviews the current and future applications, the benefits, trends and environmental and sustainability issues.
