Download or read book Behavior of Ultra high Performance Concrete Bridge Deck Panels Compared to Conventional Stay in place Deck Panels written by Valter Gora Venancio and published by . This book was released on 2016 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The remarkable features of ultra-high performance concrete (UHPC) have been reported. Its application in bridge construction has been an active research area in recent years, attributed to its higher compressive strength, higher ductility and reduced permeability when compared with conventional concrete and even high-strength concrete. Those characteristics are known to increase bridge durability and, consequently, decrease life-cycle maintenance costs. With that in mind, this study investigated the performance of UHPC stay-in-place (SIP) bridge deck panels subjected to high loads in both flexure and shear. The test matrix consisted of twelve (12) half-scale panels that were 4 feet long and 2 feet wide. The variable parameters that were studied included thickness (i.e., 2-in. and 3-in.) as well as non-discrete reinforcement type, including conventional mild reinforcement, welded wire mesh and no reinforcement (UHPC only). Control deck panels with conventional concrete (CC) were fabricated and tested to serve as a baseline for comparison. The results indicated that the UHPC panels had an improved performance compared to the conventional concrete panels. With respect to the panels tested in high shear loads, only the CC panel test resulted in a diagonal tension failure mode (i.e. traditional shear type failure). All of the other UHPC panels failed in flexure suggesting that the UHPC provided a high shear capacity. The results also showed a good correlation with selected empirical models. A cost study was also investigated. It was concluded that, even with the high difference between the prices per cubic yard of both concretes, the difference can be significantly lower when compared with the prices per ultimate load capacity"--Abstract, page iii.

Download or read book High Performance Eco Efficient Concrete written by Carlos Thomas and published by MDPI. This book was released on 2021-05-26 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is dedicated to “High-Performance Eco-Efficient Concrete” and concrete fatigue behavior, more sustainable construction materials, capable of complying with quality standards and current innovation policies, aimed at saving natural resources and reducing global pollution. The development of self-compacting concretes with electric arc furnace slags is a further achievement. In addition, the technical and economic viability of using coarse recycled aggregates from crushed concrete in shotcrete, enhanced quality and reduced on-site construction time are the basic features of prefabricated bridge elements and systems, biomass bottom ash as aluminosilicate precursor and phosphogypsum were discussed. On the other hand, basalt fiber improving the mechanical properties and durability of reactive powder concrete, alkali-activated slag and high-volume fly ash and the potential of phosphogypsum as secondary raw material in construction industry, the effects of fly ash on the diffusion, bonding, and microproperties of chloride penetration in concrete were studied. Increasing amounts of sustainable concretes are being used as society becomes more aware of the environment. Finally, the circular economy as an economic model of production and consumption that involves reusing, repairing, refurbishing, and recycling materials after their service life are presented in this book.

Download or read book Numerical Analysis and Experimental Investigation of Ultra high performance Concrete Hybrid Bridge Deck Connections written by Sabreena Nasrin and published by . This book was released on 2019 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years, the use of modular bridge deck components has gained popularity for facilitating more durable components in bridge decks, but these components require field-applied connections for constructing the entire bridge. Ultra-High-Performance Concrete (UHPC) is being extensively used for highway bridges in the field connections between girders and deck panels for its superior quality than conventional concrete.Thus far, very limited data is available on the modeling of hybrid-bridge deck connections. In this study, finite element models have been developed to identify the primary properties affecting the response of hybrid deck panel system under monotonic and reverse cyclic loads. The commercial software ABAQUS was used to validate the models and to generate the data presented herein. The concrete damage plasticity (CDP) model was used to simulate both the conventional concrete and UHPC. In addition, numerical results were validated against experimental data available in the literature. The key parameters studied were the mesh size, the dilation angle, reinforcement type, concrete constitutive models, steel properties, and the contact type between the UHPC and the conventional concrete. The models were found to capture the load-deformation response, failure modes, crack patterns and ductility indices satisfactorily. The damage in concrete under monotonic loading is found higher in normal concrete than UHPC with no signs of de-bonding between the two materials. It is observed that increasing the dilation angle leads to an increase in the initial stiffness of the model. Changing the dilation angle from 20℗ʻ to 40℗ʻ results in an increase of 7.81% in ultimate load for the panel with straight reinforcing bars, whereas for the panel with headed bars, the increase in ultimate load was found 8.56 %.Furthermore, four different types of bridge deck panels were simulated under reversed cyclic loading to observe overall behavior and the damage pattern associated with the reversed cyclic load. The key parameters investigated were the configurations of steel connections between the precast concrete deck elements, the loading position, ductility index, and the failure phenomena. The headed bar connections were found to experience higher ductility than the ones with straight bars in the range of 10.12% to 30.70% in all loading conditions, which is crucial for ensuring safe structural performance. This numerical investigation provides recommendations for predicting the location of the local damage in UHPC concrete bridge deck precast panel connections under reversed cyclic loading.Despite of having excellent mechanical and material properties, the use of Ultra-High-Performance Fiber Reinforced Concrete (UHP-FRC) is not widespread due to its high cost and lack of widely accepted design guidelines. This research also aims to develop a UHPC mixture using locally and domestically available materials without heat curing in hopes of reducing the production cost. Several trial mixtures of UHPC have been developed using locally available basalt and domestically available steel fibers. Among them, one trial mixture of 20.35 ksi compressive strength was selected for further study. To investigate the applicability of this locally produced UHPC in bridge closure, two full scale-8 ft. span hybrid bridge deck slabs with UHPC closure were constructed and tested under monotonic loading to identify the structural and material responses. The load-deflection response of the hybrid connection confirms that the deflection increased linearly until the initiation of first crack, after that it increased non-linearly up to the failure of the connection. The strain response also confirms that UHPC experiences less strain than normal strength concrete under compression loading. In addition, a moment curvature analytical graphical user interface model of hybrid bridge deck connection has been developed using MATLAB to predict ductility, curvature, and the stress distributions in those connections. The predicted value of moment and curvature from the code was found in good agreement with experimental data as well. The code provides a tool to professional engineers to predict ductility, curvature, and the stress distributions in those connections. The code is built in such a way to allow various input parameters such as concrete strength, dimensions of hybrid connection and deck panels, reinforcement configuration and the shape of the connection.Though, ultra-high-performance fiber reinforced concrete (UHP-FRC) has very high compressive strength compared to conventional concrete, the failure strain of UHP-FRC is not enough to withstand large plastic deformations under high stain rate loading such as impact and blast loading. Hence, a numerical study has been conducted to simulate low-velocity impact phenomenon of UHP-FRC. The responses obtained from the numerical study are in good agreement with the experimental results under impact loads. Five different types of UHP-FRC beams were simulated under impact loading to observe the global and local material responses. The key parameters investigated were the reinforcement ratio (Ï1), impact load under various drop heights (h), and the failure phenomena. It was observed that higher reinforcement ratio showed better deflection recovery under the proposed impact. Also, for a specific reinforcement ratio, the maximum deflection increases approximately 15% when drop height decreases from 100 mm to 25 mm. Moreover, the applicability of concrete damage plasticity model for impact loading is investigated. The results also provided recommendations for predicting the location of the local damage in UHP-FRC beams under impact loading.Moreover, this research work includes a nonlinear finite element analysis of high-strength concrete confined with opposing circular spiral reinforcements. The spiral reinforcement is a very common technique used for reinforcing columns in active seismic regions due to its high ductility and high energy absorption. The results are compared with previously tested small-scale concrete columns made with the same technique under monotonic axial loads. The proposed technique is developed to improve the strength and ductility of concrete columns confined with conventional spiral systems. The finite element (FE) analysis results have shown that the proposed model can predict the failure load and crack pattern of columns with reasonable accuracy. Beside this, the concrete plasticity damage showed very good results in simulating columns with opposing spirals. The FE model is used to conduct a study on the effect of spiral spacing, Îđ (ratio of the core diameter to the whole cross section diameter) and compressive strength on the behavior of circular spiral reinforced concrete columns confined with opposing circular spiral reinforcements. The results of the parametric study demonstrated that for the same spacing between spirals and same strength of concrete, increasing Îđ increases the failure load of the column. It is also observed from the study that the ductility of the studied columns is not affected by changing the value of Îđ. In addition, a correlation between the Îđ factor, three different compressive concrete strengths, and the spacing of opposing spirals was developed in this study.

Download or read book Behavior of Field cast Ultra high Performance Concrete Bridge Deck Connections Under Cyclic and Static Structural Loading written by Benjamin A. Graybeal and published by . This book was released on 2010 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The use of modular bridge deck components has the potential to produce higher quality, more durable bridge decks; however, the required connections have often proved lacking, resulting in less than desirable overall system performance. Advanced cementitious composite materials whose mechanical and durability properties far exceed those of conventional concretes present an opportunity to significantly enhance the performance of field-cast connections thus facilitating the wider use of modular bridge deck systems. Ultra-high performance concrete (UHPC) represents a class of such advanced cementitious composite materials. Of particular interest here, UHPCs can exhibit both exceptional bond when cast against previously cast concrete and can significantly shorten the development length of embedded discrete steel reinforcement. These properties allow for a redesign of the modular component connection, facilitating simplified construction and enhanced long-term system performance. This study investigated the structural performance of field-cast UHPC connections for modular bridge deck components. The transverse and longitudinal connection specimens simulated the connections between precast deck panels and the connections between the top flanges of deck-bulb-tee girders, respectively. Testing included both cyclic and static loadings. The results demonstrated that the field-cast UHPC connection facilitates the construction of an emulative bridge deck system whose behaviors should meet or exceed those of a conventional cast-in-place bridge deck"--Technical report documentation page.

Download or read book The Behaviour of Ultra high performance Concrete in Precast Concrete Bridge Deck Connections written by Heather Stefaniuk and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis studies the behaviour of ultra-high-performance concrete (UHPC) in the precast concrete bridge deck connections. The experimental program consisted of shear pocket push-out testing and full-scale bridge deck testing. The main objective was to study the UHPC performance in the shear pocket and joint connections. All specimens were statically loaded until failure. The push-out test specimens consisted of two small 45 MPa concrete slabs on either side of a built-up steel section, joined together by shear studs and UHPC shear pockets. There were three 6-stud specimens, two 3-stud specimens and two 0-stud specimens. The 6-stud specimens reached ultimate loads of 2642 kN, 2892 kN, and 3045 kN. The 3-stud specimens reached ultimate loads of 1445 kN and 1674 kN. The 0-stud specimens reached ultimate loads of 4.91 kN and 3.44 kN. The failure modes for the 6-stud and 3-stud specimens were stud failure or concrete crushing, while the 0-stud specimens failed when the UHPC and steel section surface debonded. The push-out specimens were instrumented with LVDTs, pi-gauges and strain gauges to collect data on the displacements, debonding, and shear stud strains throughout testing. The bridge deck testing included a full panel deck (FPD) and jointed panel deck (JPD). The FPD was cast monolithically with regular strength concrete and had UHPC shear pocket connections to the steel support girders. The JPD was cast as two half-size regular strength panels connected together with a UHPC joint, and connected to the steel support girders with UHPC shear pockets. The FPD and JPD reached ultimate loads of 1926 kN and 1878 kN, respectively. Both decks failed by concrete punching under the load point. The bridge decks were instrumented with LVDTs, pi-gauges, and strain gauges to collect data on the deflections, crack widths, steel strains, concrete strains, and shear stud strains throughout testing. The experimental results implied the number and length of the studs in the shear pockets may be reduced. The better performance of the FPD also indicated the circular pockets were superior and the use of UHPC in precast deck connections does not significantly improve the overall performance.

Download or read book High Performance Concrete Bridge Decks A Fast Track Implementation Study Volume 1 Structural Behavior written by Robert J. Frosch and published by Purdue University Press. This book was released on 2008-11-01 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Transverse cracking of concrete bridge decks is problematic in numerous states. Cracking has been identified in the negative and positive moment regions of bridges and can appear shortly after opening the structure to live loads. To improve the service life of the bridge deck as well as decrease maintenance costs, changes to current construction practices in Indiana are being considered. A typical bridge deck was instrumented which incorporated the following: increased reinforcement amounts, decreasing reinforcement spacing, and high-performance, low-shrinkage concrete. The low shrinkage concrete was achieved using a ternary concrete mix. The objective of this research was to determine the performance, particularly in terms of transverse cracking and shrinkage, of a bridge incorporating design details meant to reduce cracking. Based on measurements from the bridge, it was determined that maximum tensile strains experienced in the concrete were not sufficient to initiate cracking. An on-site inspection was performed to confirm that cracking had not initiated. The data was analyzed and compared with the behavior of a similarly constructed bridge built with nearly identical reinforcing details, but with a more conventional concrete to evaluate the effect of the HPC. Based on this study, it was observed that full-depth transverse cracks did not occur in the structure and that the use of HPC lowered the magnitude of restrained shrinkage strains and resulting tensile stresses.

Download or read book Experimental Evaluation of Full Depth Precast prestressed Concrete Bridge Deck Panels written by Mohsen A. Issa and published by . This book was released on 2002 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: A literature review concerning the objectives of the project was completed. A significant number of published papers, reports, etc., were examined to determine the effectiveness of full depth precast panels for bridge deck replacement. A detailed description of the experimental methodology was developed which includes design and fabrication of the panels and assembly of the bridge. The design and construction process was carried out in cooperation with the project Technical Review Panel. The major components of the bridge deck system were investigated. This includes the transverse joints and the different materials within the joint as well as composite action. The materials investigated within the joint were polymer concrete, non-shrink grout, and set-45 for the transverse joint. The transverse joints were subjected to direct shear tests, direct tension tests, and flexure tests. These tests exhibited the excellent behavior of the system in terms of strength and failure modes. Shear key tests were also conducted. The shear connection study focused on investigating the composite behavior of the system based on varying the number of shear studs within a respective pocket as well as varying the number of pockets within a respective panel. The results indicated that this shear connection is extremely efficient in rendering the system under full composite action. Finite element analysis was conducted to determine the behavior of the shear connection prior to initiation of the actual full scale tests. In addition, finite element analysis was also performed with respect to the transverse joint tests in an effort to determine the behavior of the joints prior to actual testing. The most significant phase of the project was testing a full-scale model. The bridge was assembled in accordance with the procedures developed as part of the study on full-depth precast panels and the results obtained through this research. The system proved its effectiveness in withstanding the applied loading that exceeded eight times the truck loading in addition to the maximum negative and positive moment application. Only hairline cracking was observed in the deck at the maximum applied load. Of most significance was the fact that full composite action was achieved between the precast panels and the steel supporting system, and the exceptional performance of the transverse joint between adjacent panels.

Download or read book Full depth Precast Concrete Bridge Deck Panel Systems written by Sameh S. Badie and published by Transportation Research Board. This book was released on 2008 with total page 119 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Structural Performance of a Full depth Precast Concrete Bridge Deck System written by Thomas Mander and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Throughout the United States accelerated bridge construction is becoming increasingly popular to meet growing transportation demands while keeping construction time and costs to a minimum. This research focuses on eliminating the need to form full-depth concrete bridge deck overhangs, accelerating the construction of concrete bridge decks, by using full-depth precast prestressed concrete deck panels. Full-depth precast overhang panels in combination with cast-in-place (CIP) reinforced concrete are experimentally and analytically investigated to assess the structural performance. Experimental loaddeformation behavior for factored AASHTO LRFD design load limits is examined followed by the collapse capacity of the panel-to-panel seam that exists in the system. Adequate strength and stiffness of the proposed full-depth panels deem the design safe for implementation for the Rock Creek Bridge in Fort Worth, Texas. New failure theories are derived for interior and exterior bridge deck spans as present code-based predictions provide poor estimates of the ultimate capacity. A compound shear-flexure failure occurs at interior bays between the CIP topping and stay-in-place (SIP) panel. Overhang failure loads are characterized as a mixed failure of flexure on the loaded panel and shear at the panel-to-panel seam. Based on these results design recommendations are presented to optimize the reinforcing steel layout used in concrete bridge decks.

Download or read book Influence of Precast Concrete Panel Surface Condition on Behavior of Composite Bridge Decks at Skewed Expansion Joints written by Kristen Shawn Donnelly and published by . This book was released on 2009 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Following development of rectangular prestressed, precast concrete panels (PCP) that could be used as stay-in-place formwork adjacent to expansion joints in bridge decks, the Texas Department of Transportation (TxDOT) initiated a research effort to investigate the use of PCP units at skewed expansion joints. The fabrication of trapezoidal PCP units was studied and the response of skewed panels with 45° and 30° skew angles was obtained. The panels were topped with a 4 in. thick cast-in-place (CIP) slab to complete the bridge deck. Specimens with 45° skew performed well under service and overload levels. The deck failed in diagonal shear at loads well over the design level loads. However, two 30° specimens failed prematurely by delamination between the topping slab and the PCP. The cause of the delamination was insufficient shear transfer capacity between the PCP and CIP topping slab. For the specimens tested at a square end, the failure mode was punching shear at high loads for all specimens. The surface condition of the PCP was specified to have a "broom finish" and the panel was to have a saturated surface dry (SSD) condition so that PCP units would not leach moisture from the CIP topping slab. Neither of these conditions was satisfied in the two panels that failed prematurely. Although the panels were specified to have a broom finish, the panel surface had regions that were quite smooth. The objective of this research project was to reinvestigate the response of 30° PCP at an expansion joint following specified procedures for finish and moisture conditions. One specimen was constructed with a rectangular panel placed between two 30° skewed panels. These panels had a much rougher surface texture than the previously tested panels that failed in delamination. The skewed ends of the specimen were subjected to monotonically increasing static loads at midspan of the panel ends. The panels failed in diagonal shear and the response of the tested specimen confirmed that the panel surface roughness, and not the skew angle, caused delamination with the previously tested specimens. While TxDOT does not currently specify a minimum panel surface roughness, a surface roughness of approximately 1/4 in. is required in some codes for developing composite action. In addition, wetting the panels to a SSD condition prior to placement of the topping slab further enhances shear transfer between the topping slab and the PCP.

Download or read book Recommendations for the Connection Between Full depth Precast Bridge Deck Panel Systems and Precast I beams written by and published by . This book was released on 2007 with total page 75 pages. Available in PDF, EPUB and Kindle. Book excerpt: Precast bridge deck panels can be used in place of a cast-in-place concrete deck to reduce bridge closure times for deck replacements or new bridge construction. The panels are prefabricated at a precasting plant providing optimal casting and curing conditions, which should result in highly durable decks. Precast panels can be either full-depth or partial-depth. Partial-depth panels act as a stay-in-place form for a cast-in-place concrete topping. This study investigated only the behavior of full-depth precast panels. The research described in this report had two primary objectives. The first was to develop a performance specification for the grout that fills the haunch between the top of the beam and the bottom of the deck panel, as well as the horizontal shear connector pockets and the panel-to-panel joints. Tests were performed using standard or modified ASTM tests to determine basic material properties on eight types of grout. The grouts were also used in tests that approximated the conditions in a deck panel system. Based on these tests, requirements for shrinkage, compressive strength, and flow were established for the grouts. It was more difficult to establish a test method and an acceptable performance level for adhesion, an important property for the strength and durability of the deck panel system. The second objective was to quantify the horizontal shear strength of the connection between the deck panel and the beam prestressed concrete beams. This portion of the research also investigated innovative methods of creating the connection. Push-off tests were conducted using several types of grout and a variety of connections. These tests were used to develop equations for the horizontal shear strength of the details. Two promising alternate connections, the hidden pocket detail and the shear stud detail, were tested for constructibility and strength. The final outcome of this study a set of recommendations for the design, detailing, and construction of the connection between full-depth precast deck panels and prestressed concrete I-beams. If designed and constructed properly, the deck panel system is an excellent option when rapid bridge deck construction or replacement is required.

Download or read book Rapid Replacement of Bridge Decks written by Maher K. Tadros and published by Transportation Research Board. This book was released on 1998 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Long term Performance of Polymer Concrete for Bridge Decks written by David W. Fowler and published by Transportation Research Board. This book was released on 2011 with total page 75 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Synthesis 423: Long-Term Performance of Polymer Concrete for Bridge Decks addresses a number of topics related to thin polymer overlays (TPOs). Those topics include previous research, specifications, and procedures on TPOs; performance of TPOs based on field applications; the primary factors that influence TPO performance; current construction guidelines for TPOs related to surface preparation, mixing and placement, consolidation, finishing, and curing; repair procedures; factors that influence the performance of overlays, including life-cycle cost, benefits and costs, bridge deck condition, service life extension, and performance; and successes and failures of TPOs, including reasons for both.

Download or read book Stay in place Deck Panels written by Ariel Goldman and published by . This book was released on 1995 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental and Analytical Study of Concrete Bridge Decks Constructed with FRP Stay in place Forms and FRP Grid Reiforcing written by David Allan Dieter and published by . This book was released on 2002 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation of the Fatigue Behavior of Bridge Decks with Precast Panels at Expansion Joints written by Lewis Samuel Agnew and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Development of Composite Renewal Systems for Rapid Rehabilitation and Construction of Bridge Decks written by Anna Beth Pridmore and published by . This book was released on 2009 with total page 379 pages. Available in PDF, EPUB and Kindle. Book excerpt: The deterioration of steel in aging reinforced concrete bridges is a continual problem which could benefit from improved rehabilitation techniques that take advantage of enhanced and more durable materials such as fiber reinforced polymer (FRP) composites. Appropriately designed hybrid material systems benefit from the performance and durability advantages of FRP materials yet remain more cost effective than comparable all-composite systems. Development of rapid rehabilitation systems for the decks of concrete box girder bridges, which are increasingly common throughout the United States, is presented. One goal of this research is to assess and validate the use of FRP composite panels for use as both stay-in-place formwork and as the bottom longitudinal and transverse reinforcement in the deck of concrete box girder bridges. Performance assessments for full-scale two-cell box girder bridge specimens through monotonic and extensive cyclic loading provided validation for the FRP panel system bridge deck as a viable rehabilitation solution for box girder bridge decks. The FRP panel system performed comparably to a conventionally reinforced concrete bridge deck in terms of serviceability, deflection profiles, and system level structural interaction and performed superior to the RC bridge deck in terms of residual deflections, and structural response under cyclic loading. Assessment of a damaged FRP panel bridge deck system, which was repaired using a resin injection technique, showed superior performance for the repaired system in terms of integrity of the FRP panel interface and cyclic response. Rapid rehabilitation techniques for strengthening reinforced concrete box girder bridge deck overhangs using near-surface-mounted (NSM) carbon fiber reinforced polymer (CFRP) were also evaluated. Analytical predictions of load carrying capacity and deflections provided correlation with experimental results, and the developed analysis methods provide an effective design tool for future research. Results from the laboratory testing of a bridge deck overhang strengthened with FRP showed significant increases in load carrying capacity as well as deformation capacity as compared to the as-built specimen without FRP. This research provides enhanced understanding of hybrid structures and indicates significant potential for rehabilitation applications to concrete box girder bridges.