Download or read book Balancing of High Speed Machinery written by Mark S. Darlow and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 197 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern rotating machinery, particularly turbomachinery, is frequently being designed to operate at higher speeds than in the past. Consequently, there is an increased need to balance high-speed rotors. The purpose of this book is to provide the engineering student or practicing engineer with a single, complete reference on high-speed rotor balancing. To this end, a detailed analytical background and practical application procedures are presented for each of the principal high-speed rotor balancing methods, i.e. modal balancing, influence coefficient balancing and the Unified Balancing Approach. This information is supplemented and supported through a presentation of the theoretical development of synchronous rotor vibration and a brief overview of rigid rotor balancing techniques and machines. This is the first time this material is available in a single, concise volume, together with detailed descriptions of application procedures.
Download or read book Practical Balancing of Rotating Machinery written by Derek Norfield and published by Elsevier. This book was released on 2011-04-18 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rotating machinery (eg pumps, motors, compressors) is normally manufactured to precise measurements but there comes a point when the costs of manufacture mean that further precision is not cost-effective and thus any slight imbalance inherent in the machine will need to be attended to after manufacture. When such machinery is in operation, often at very high speeds of thousands of revs per minute, any imbalance will set up vibration and often noise. In addition, such imbalance will cause extra wear and loss of efficiency in the machine. The answer is to balance the affected parts of the machine so that it operates smoothly and efficiently. This book is a practical account of such balancing techniques e.g how to balance a rotor, how to set up and verify performance of a balancing machine, and procedures for on-site balancing. In addition, other common causes of vibration will be covered e.g. misalignment, bad bearings and looseness. This book is the distillation of a successful course run by the author and developed over 20 years. University engineering departments do not teach balancing techniques beyond the very basic, and there is a need for educators and engineers to have a practical book available on the topic. · A practical book which will help the reader understand the importance of balance in today's high technology world · Outlines the history of dynamic balancing and other vibration reduction techniques · Profusely illustrated throughout
Download or read book Dynamic and Static Balancing written by Edward K. Hammond and published by . This book was released on 1921 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Dynamic Balancing of Rotating Machinery written by John Bernard Wilcox and published by . This book was released on 1967 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Speed Balancing Technology and Equipment written by Sheping Tian and published by China's Major Science and Tech. This book was released on 2020-01-03 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives an introduction to the high-speed balancing technology and equipment of flexible rotors, explaining the fundamental concepts and principles, construction and basic design of high-speed balancing machines and overspeed test camber as well as the technical specifications of DG-series high-speed balancing machines. This book is intended for engineering staffs and researchers in the field of high-speed balancing, as well as senior undergraduates, graduate students and university teachers.
Download or read book Machinery Vibration written by Victor Wowk and published by McGraw-Hill Professional Publishing. This book was released on 1995 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: Shows you how to implement simple methods to mass balance without expensive instruments, and explores such topics as the vestor mathematics of balancing, mass centering, index balancing, and designs for balance weights. It features several illustrations, real-world case studies, and worked-out problems.
Download or read book Rotating Machinery written by Robert B. McMillan and published by CRC Press. This book was released on 2020-11-26 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: A theoretical and practical understanding of unbalance and misalignment in rotating equipment is presented here. These two conditions account for the vast majority of problems with rotating equipment encountered in the real world.;Numerous examples and solutions are included to assist in understanding the various concepts. Included is information on vibration and how it is used to determine the operational integrity of rotating machinery. Also detailed are the relationships between various vibration characteristics which provide an understanding of the forces generated within operating machinery when conditions of unbalance and misalignment are present. Resonance and beat frequencies are detailed along with sources and cures.;Also covered are proper inspection procedures, single plane and dual plane methods of balancing rotating equipment, the three circle method of balancing slow speed fans, advanced rim and face method of precision alignment, and the reverse indicator method of alignment plus much more to fortify the learning experience.
Download or read book Rotor Balancing written by Hatto Schneider and published by Springer Nature. This book was released on 2023-07-03 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: Für die Qualitätssicherung von Rotoren ist das Auswuchten ein unverzichtbarer Schritt. Dabei verändern sich mit jeder Weiterentwicklung der Rotoren die Anforderungen an die Auswuchttechnik. Wichtige Prinzipien des Auswuchtens werden in dem Buch erklärt. Es dient als Werkzeug, um die stets neu auftretenden Probleme beim Auswuchten sachgerecht und wirtschaftlich lösen zu können. In der 8. Auflage wird die neue Norm DIN ISO 19499 ausführlich erläutert. Die beabsichtigten Bearbeitungen aller Auswuchtnormen vonseiten des DIN werden erstmals beschrieben.
Download or read book Adaptive Optimal Control of Active Balancing Systems for High speed Rotating Machinery written by Stephen W. Dyer and published by . This book was released on 1999 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Practical Machinery Vibration Analysis and Predictive Maintenance written by Cornelius Scheffer and published by Elsevier. This book was released on 2004-07-16 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Machinery Vibration Analysis and Predictive Maintenance provides a detailed examination of the detection, location and diagnosis of faults in rotating and reciprocating machinery using vibration analysis. The basics and underlying physics of vibration signals are first examined. The acquisition and processing of signals is then reviewed followed by a discussion of machinery fault diagnosis using vibration analysis. Hereafter the important issue of rectifying faults that have been identified using vibration analysis is covered. The book also covers the other techniques of predictive maintenance such as oil and particle analysis, ultrasound and infrared thermography. The latest approaches and equipment used together with the latest techniques in vibration analysis emerging from current research are also highlighted. Understand the basics of vibration measurement Apply vibration analysis for different machinery faults Diagnose machinery-related problems with vibration analysis techniques
Download or read book Rotordynamics 2 written by Neville F. Rieger and published by Springer. This book was released on 2014-05-04 with total page 579 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Rotor Dynamics written by J. S. Rao and published by New Age International. This book was released on 1996 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Third Revised And Enlarged Edition Of The Book Presents An In-Depth Study Of The Dynamic Behaviour Of Rotating And Reciprocating Machinery. It Evolved Out Of Lectures Delivered At Different Universities Over The Last Two Decades. The Book Deals With Torsional And Bending Vibrations Of Rotors, Stability Aspects, Balancing And Condition Monitoring. Closed Form Solutions Are Given Wherever Possible And Parametric Studies Presented To Give A Clear Understanding Of The Subject. Transfer Matrix Methods Is Extensively Used For General Class Of Rotors For Both Bending And Torsional Vibrations.Special Attentions Are Given To Transient Analysis Of The Rotors Which Is Becoming An Essential Part Of The Design Of High Speed Machinery. Systems With Fluid Film Bearings, Cracked Rotors And Two Spool Rotors Are Also Presented.A First Course On Theory Of Vibration Is A Prerequisite To This Study. Analysis Used Is Fairly Simple, But Sufficiently Advanced To The Requisite Level Of Predicting Practical Observations. As Far As Possible, Practical Examples Are Illustrated, So That The Book Is Also Useful To Practising Engineers.A Special Feature Of This Book Is Diagnostics Of Rotating Machinery Using Vibration Signature Analysis And Application Of Expert Systems To A Field Engineer In Trouble Shooting Work.
Download or read book Dynamics of Machinery written by Hans Dresig and published by Springer Science & Business Media. This book was released on 2010-07-27 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dynamic loads and undesired oscillations increase with higher speed of machines. At the same time, industrial safety standards require better vibration reduction. This book covers model generation, parameter identification, balancing of mechanisms, torsional and bending vibrations, vibration isolation, and the dynamic behavior of drives and machine frames as complex systems. Typical dynamic effects, such as the gyroscopic effect, damping and absorption, shocks, resonances of higher order, nonlinear and self-excited vibrations are explained using practical examples. These include manipulators, flywheels, gears, mechanisms, motors, rotors, hammers, block foundations, presses, high speed spindles, cranes, and belts. Various design features, which influence the dynamic behavior, are described. The book includes 60 exercises with detailed solutions. The substantial benefit of this "Dynamics of Machinery" lies in the combination of theory and practical applications and the numerous descriptive examples based on real-world data. The book addresses graduate students as well as engineers.
Download or read book American Machinist written by and published by . This book was released on 1909 with total page 1128 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances on Analysis and Control of Vibrations written by Mauricio Zapateiro and published by BoD – Books on Demand. This book was released on 2012-09-05 with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt: Vibration is a phenomenon that we can perceive in many systems. Their effects are as diverse as the personal discomfort that can produce the unevenness of a road or the collapse of a building or a bridge during an earthquake. This book is a compendium of research works on vibration analysis and control. It goes through new methodologies that help us understand and mitigate this phenomenon. This book is divided into two sections. The first one is devoted to new advances on vibration analysis while the second part is a series of case studies that illustrate novel techniques on vibration control. The applications are varied and include areas such as vehicle suspension systems, wind turbines and civil engineering structures.
Download or read book Balancing of Rigid and Flexible Rotors written by Neville F. Rieger and published by . This book was released on 1986 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machinery and Production Engineering written by and published by . This book was released on 1918 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt:
