Download or read book Applying Risk Informed Methodologies to Improve the Economics of Sodium cooled Fast Reactors written by Christopher C. Nitta and published by . This book was released on 2010 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to support the increasing demand for clean sustainable electricity production and for nuclear waste management, the Sodium-Cooled Fast Reactor (SFR) is being developed. The main drawback has been its high capital and operating costs in comparison with traditional light water reactors. In order to compete, the SFR must be shown to be economically competitive. This study makes use of the proposed Technology Neutral Framework (TNF) being developed by the U.S. NRC. By applying this risk-based approach to safety, rather than the traditional approach of applying deterministic requirements, it will be shown that significant savings can be realized without compromising fundamental safety. A methodology was developed using the Technology Neutral Framework to judge design alternatives based on risk significance that provide acceptable safety within the framework at less cost. The key probabilistic metrics of Risk Achievement Worth and Limit Exceedence Factor will be used to assess whether a system or component plays an important safety function. If not the system, structure or component either can be eliminated, modified or its safety grade can be reduced resulting in cost savings. In addition, assessments were made to determine how to improve thermal efficiency by raising reactor exit temperature and by applying other design alternatives to reduce costs as evaluated on a safety, reliability and economic basis.

Download or read book RISK INFORMED BALANCING OF SAFETY NONPROLIFERATION AND ECONOMICS FOR THE SFR written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A substantial barrier to the implementation of Sodium-cooled Fast Reactor (SFR) technology in the short term is the perception that they would not be economically competitive with advanced light water reactors. With increased acceptance of risk-informed regulation, the opportunity exists to reduce the costs of a nuclear power plant at the design stage without applying excessive conservatism that is not needed in treating low risk events. In the report, NUREG-1860, the U.S. Nuclear Regulatory Commission describes developmental activities associated with a risk-informed, scenario-based technology neutral framework (TNF) for regulation. It provides quantitative yardsticks against which the adequacy of safety risks can be judged. We extend these concepts to treatment of proliferation risks. The objective of our project is to develop a risk-informed design process for minimizing the cost of electricity generation within constraints of adequate safety and proliferation risks. This report describes the design and use of this design optimization process within the context of reducing the capital cost and levelized cost of electricity production for a small (possibly modular) SFR. Our project provides not only an evaluation of the feasibility of a risk-informed design process but also a practical test of the applicability of the TNF to an actual advanced, non-LWR design. The report provides results of five safety related and one proliferation related case studies of innovative design alternatives. Applied to previously proposed SFR nuclear energy system concepts We find that the TNF provides a feasible initial basis for licensing new reactors. However, it is incomplete. We recommend improvements in terms of requiring acceptance standards for total safety risks, and we propose a framework for regulation of proliferation risks. We also demonstrate methods for evaluation of proliferation risks. We also suggest revisions to scenario-specific safety risk acceptance standards, particularly concerning seismic and aircraft impactrelated risks. Most importantly, within the context of the TNF historical SFR safety concerns about energetic core disruptive accidents are seen to be unimportant, but those of rare scenarios mentioned above are seen to be of dominant concern. In terms of proliferation risks the SFR energy system is seen not to be of considerably greater concern than with other nuclear power technologies, providing that highly effective safeguards are employed. We find the economic performance of proposed SFRs likely, due to the problems of using sodium as a coolant, to be inferior to those of LWRs unless they can be credited for services to improve nuclear waste disposal, nuclear fuel utilization and proliferation risk reductions. None of the design innovations investigated offers the promise to reverse this conclusion. The most promising innovation investigated is that of improving the plant's thermodynamic efficiency via use of the supercritical CO2 (rather than steam Rankine) power conversion system. We were unable to reach conclusions about the economic and proliferation risk implications of competing nuclear fuel processing methods, as available designs are too little developed to justify any such results. Overall, we find the SFR to be a promising alternative to LWRs should the conditions governing the valuation change substantially from current ones.

Download or read book Application of the Technology Neutral Framework to Sodium Cooled Fast Reactors written by Brian Carl Johnson and published by . This book was released on 2010 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sodium cooled fast reactors (SFRs) are considered as a novel example to exercise the Technology Neutral Framework (TNF) proposed in NUREG- 1860. One reason for considering SFRs is that they have historically had a licensing problem due to postulated core disruptive accidents. Two SFR designs are considered, and both meet the goals of the TNF that LWRs typically would not. Considering these goals have been met, a method for improving economics is proposed where systems of low risk-importance are identified as candidates for removal, simplification, or removal from safety grade. Seismic risk dominates these designs and is found to be a limiting factor when applying the TNF. The contributions of this thesis are the following: 1. Functional event trees are developed as a tool to allow different designs to be compared on an equal basis. Functional event trees are useful within the TNF as a method for the selection of Licensing Basis Events (LBEs) which take the place of traditional Design Basis Accidents. 2. A new importance measure, Limit Exceedance Factor (LEF), is introduced that measures the margin in system failure probability. It can be used directly with the TNF where standard importance measures cannot. It also reveals that some systems that appear to be of high risk-importance with standard importance measures may have significant margin. 3. The seismic risk dominates these designs. It is shown that even under optimistic assumptions, the goals of the TNF cannot be met by a typical reactor. The effect of seismic isolation to reduce the frequency of seismically initiated large releases is also analyzed and found to be insufficient to reach the goals of the TNF. A limit on initiating event frequency that is consistent with current practices is proposed.

Download or read book Status of Fast Reactor Research and Technology Development written by International Atomic Energy Agency and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Based on a recommendation from the Technical Working Group on Fast Reactors, this publication is a regular update of previous publications on fast reactor technology. The publication provides comprehensive and detailed information on the technology of fast neutron reactors. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors. The main issues of discussion are experience in design, construction, operation and decommissioning, various areas of research and development, engineering, safety and national strategies, and public acceptance of fast reactors. In the summary the reader will find national strategies, international initiatives on innovative (i.e. Generation IV) systems and an assessment of public acceptance as related to fast reactors."--Résumé de l'éditeur.

Download or read book Liquid Metal Cooled Reactors written by International Atomic Energy Agency and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presents a survey of worldwide experience gained with fast breeder reactor design, development and operation. Coverage includes state of the art of liquid metal fast reactor development; lead-bismuth cooled (LBC) ship reactor operation experience and LBC fast power reactor development; and treatment and disposal of spent sodium.

Download or read book Handbook of Generation IV Nuclear Reactors written by Igor Pioro and published by Woodhead Publishing. This book was released on 2022-12-07 with total page 1112 pages. Available in PDF, EPUB and Kindle. Book excerpt: Handbook of Generation IV Nuclear Reactors, Second Edition is a fully revised and updated comprehensive resource on the latest research and advances in generation IV nuclear reactor concepts. Editor Igor Pioro and his team of expert contributors have updated every chapter to reflect advances in the field since the first edition published in 2016. The book teaches the reader about available technologies, future prospects and the feasibility of each concept presented, equipping them users with a strong skillset which they can apply to their own work and research. Provides a fully updated, revised and comprehensive handbook dedicated entirely to generation IV nuclear reactors Includes new trends and developments since the first publication, as well as brand new case studies and appendices Covers the latest research, developments and design information surrounding generation IV nuclear reactors

Download or read book Management of Nuclear Power Plant Projects written by IAEA and published by International Atomic Energy Agency. This book was released on 2020-11-25 with total page 221 pages. Available in PDF, EPUB and Kindle. Book excerpt: Member States intending to introduce a nuclear power programme will need to pass through several phases during the implementation. Experience shows that careful planning of the objectives, roles, responsibilities, interfaces and tasks to be carried out in different phases of a nuclear project is important for success. This publication presents a harmonized approach that may be used to structure the owner/operator management system and establish and manage nuclear projects and their development activities irrespective of the adopted approach. It has been developed from shared management practices and consolidated experiences provided by nuclear project management specialists through a series of workshops and working groups organized by the IAEA. The resultant publication presents a useful framework for the management of nuclear projects from initiation to closeout and captures international best practices.

Download or read book Safety of Nuclear Power Plants written by International Atomic Energy Agency and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: On the basis of the principles included in the Fundamental Safety Principles, IAEA Safety Standards Series No. SF-1, this Safety Requirements publication establishes requirements applicable to the design of nuclear power plants. It covers the design phase and provides input for the safe operation of the power plant. It elaborates on the safety objective, safety principles and concepts that provide the basis for deriving the safety requirements that must be met for the design of a nuclear power plant. Contents: 1. Introduction; 2. Applying the safety principles and concepts; 3. Management of safety in design; 4. Principal technical requirements; 5. General plant design; 6. Design of specific plant systems.

Download or read book Improving Fuel Cycle Design and Safety Characteristics of a Gas Cooled Fast Reactor written by Willem Frederik Geert van Rooijen and published by IOS Press. This book was released on 2006 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Generation IV Forum is an international nuclear energy research initiative aimed at developing the fourth generation of nuclear reactors, envisaged to enter service halfway the 21st century. One of the Generation IV reactor systems is the Gas Cooled Fast Reactor (GCFR), the subject of study in this thesis. The Generation IV reactor concepts should improve all aspects of nuclear power generation. Within Generation IV, the GCFR concept specifically targets sustainability of nuclear power generation. The Gas Cooled Fast Reactor core power density is high in comparison to other gas cooled reactor concepts. Like all nuclear reactors, the GCFR produces decay heat after shut down, which has to be transported out of the reactor under all circumstances. The layout of the primary system therefore focuses on using natural convection Decay Heat Removal (DHR) where possible, with a large coolant fraction in the core to reduce friction losses.

Download or read book Chemical Engineering Design written by Gavin Towler and published by Elsevier. This book was released on 2012-01-25 with total page 1321 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemical Engineering Design, Second Edition, deals with the application of chemical engineering principles to the design of chemical processes and equipment. Revised throughout, this edition has been specifically developed for the U.S. market. It provides the latest US codes and standards, including API, ASME and ISA design codes and ANSI standards. It contains new discussions of conceptual plant design, flowsheet development, and revamp design; extended coverage of capital cost estimation, process costing, and economics; and new chapters on equipment selection, reactor design, and solids handling processes. A rigorous pedagogy assists learning, with detailed worked examples, end of chapter exercises, plus supporting data, and Excel spreadsheet calculations, plus over 150 Patent References for downloading from the companion website. Extensive instructor resources, including 1170 lecture slides and a fully worked solutions manual are available to adopting instructors. This text is designed for chemical and biochemical engineering students (senior undergraduate year, plus appropriate for capstone design courses where taken, plus graduates) and lecturers/tutors, and professionals in industry (chemical process, biochemical, pharmaceutical, petrochemical sectors). New to this edition: Revised organization into Part I: Process Design, and Part II: Plant Design. The broad themes of Part I are flowsheet development, economic analysis, safety and environmental impact and optimization. Part II contains chapters on equipment design and selection that can be used as supplements to a lecture course or as essential references for students or practicing engineers working on design projects. New discussion of conceptual plant design, flowsheet development and revamp design Significantly increased coverage of capital cost estimation, process costing and economics New chapters on equipment selection, reactor design and solids handling processes New sections on fermentation, adsorption, membrane separations, ion exchange and chromatography Increased coverage of batch processing, food, pharmaceutical and biological processes All equipment chapters in Part II revised and updated with current information Updated throughout for latest US codes and standards, including API, ASME and ISA design codes and ANSI standards Additional worked examples and homework problems The most complete and up to date coverage of equipment selection 108 realistic commercial design projects from diverse industries A rigorous pedagogy assists learning, with detailed worked examples, end of chapter exercises, plus supporting data and Excel spreadsheet calculations plus over 150 Patent References, for downloading from the companion website Extensive instructor resources: 1170 lecture slides plus fully worked solutions manual available to adopting instructors

Download or read book Basic Safety Principles for Nuclear Power Plants written by International Nuclear Safety Advisory Group and published by . This book was released on 1999 with total page 118 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present report is a revision of Safety Series No. 75-INSAG-3 (1988), updating the statements made on the objectives and principles of safe design and operation for electricity generating nuclear power plants. It includes the improvements made in the safety of operating nuclear power plants and identifies the principles underlying the best current safety policies to be applied in future plants. It presents INSAG's understanding of the principles underlying the best current safety policies and practices of the nuclear power industry.

Download or read book The Technological and Economic Future of Nuclear Power written by Reinhard Haas and published by Springer. This book was released on 2019-01-01 with total page 385 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book discusses the eroding economics of nuclear power for electricity generation as well as technical, legal, and political acceptance issues. The use of nuclear power for electricity generation is still a heavily disputed issue. Aside from technical risks, safety issues, and the unsolved problem of nuclear waste disposal, the economic performance is currently a major barrier. In recent years, the costs have skyrocketed especially in the European countries and North America. At the same time, the costs of alternatives such as photovoltaics and wind power have significantly decreased. Contents History and Current Status of the World Nuclear Industry The Dramatic Decrease of the Economics of Nuclear Power Nuclear Policy in the EU The Legacy of Csernobyl and Fukushima Nuclear Waste and Decommissioning of Nuclear Power Plants Alternatives: Heading Towards Sustainable Electricity Systems Target Groups Researchers and students in the fields of political, economic and technical sciences Energy (policy) experts, nuclear energy experts and practitioners, economists, engineers, consultants, civil society organizations The Editors Prof. Dr. Reinhard Haas is University Professor of energy economics at the Institute of Energy Systems and Electric Drives at Technische Universität Wien, Austria. PD Dr. Lutz Mez is Associate Professor at the Department for Political and Social Sciences of Freie Universität Berlin, Germany. PD Dr. Amela Ajanovic is a senior researcher and lecturer at the Institute of Energy Systems and Electrical Drives at Technische Universität Wien, Austria.--

Download or read book Sodium Fast Reactors with Closed Fuel Cycle written by Baldev Raj and published by CRC Press. This book was released on 2015-04-15 with total page 901 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sodium Fast Reactors with Closed Fuel Cycle delivers a detailed discussion of an important technology that is being harnessed for commercial energy production in many parts of the world. Presenting the state of the art of sodium-cooled fast reactors with closed fuel cycles, this book:Offers in-depth coverage of reactor physics, materials, design, s

Download or read book Reduction of Capital Costs of Nuclear Power Plants written by OECD Nuclear Energy Agency and published by OECD. This book was released on 2000 with total page 122 pages. Available in PDF, EPUB and Kindle. Book excerpt: The competitiveness of nuclear power plants depends largely on their capital costs that represent some 60 per cent of their total generation costs. Reviewing and analysing ways and means to reduce capital costs of nuclear power plants are essential to enhance the economic viability of the nuclear option. The report is based upon cost information and data provided by experts from NEA Member countries. It investigates the efficiency of alternative methods for reducing capital costs of nuclear units. It will provide stakeholders from the industry and governmental agencies with relevant elements in support of policy making.

Download or read book Nuclear Energy Basic Principles written by International Atomic Energy Agency and published by . This book was released on 2008 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the rationale and vision for the peaceful use of nuclear energy. The publication identifies the basic principles that nuclear energy systems must satisfy to fulfil their promise of meeting growing global energy demands.

Download or read book Approaches for Assessing the Economic Competitiveness of Small and Medium Sized Reactors written by International Atomic Energy Agency and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication assists existing and potential stakeholders in the definition of competitive approaches regarding design and deployment of small and medium sized reactors (SMR). It provides a framework for assessment of the investment attractiveness of nuclear power plant projects that adopts small reactor to be deployed in multi-modules and incorporate modularization construction technology. Main chapters detail past experience and future plans in several IAEA Member States and present the suite of models to assist designers and guide potential users on the economic performance and investment attractiveness of SMRs. A framework for the consolidated application of such models is also suggested. The annexes, contributed by Member States, provide in depth descriptions of different assessment models and give examples of their application.

Download or read book Innovation in Nuclear Energy Technology written by and published by OECD Publishing. This book was released on 2007 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt: Innovation has been a driving force in the successful deployment of nuclear energy and remains essential today for its sustainable future. This report provides an overview of the state of the art in nuclear innovation systems, including their driving forces, main actors, institutional and legal frameworks, and infrastructure for knowledge and programme management. It also offers policy recommendations based on country reports and case studies supplied by participating member countries.