Download or read book Analysis of Sub synchronous Resonance SSR in Doubly fed Induction Generator DFIG Based Wind Farms written by Hossein Ali Mohammadpour and published by Springer Nature. This book was released on 2022-05-31 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wind power penetration is rapidly increasing in today's energy generation industry. In particular, the doubly-fed induction generator (DFIG) has become a very popular option in wind farms, due to its cost advantage compared with fully rated converter-based systems. Wind farms are frequently located in remote areas, far from the bulk of electric power users, and require long transmission lines to connect to the grid. Series capacitive compensation of DFIG-based wind farm is an economical way to increase the power transfer capability of the transmission line connecting the wind farm to the grid. For example, a study performed by ABB reveals that increasing the power transfer capability of an existing transmission line from 1300 MW to 2000 MW using series compensation is 90% less expensive than building a new transmission line. However, a factor hindering the extensive use of series capacitive compensation is the potential risk of subsynchronous resonance (SSR). The SSR is a condition where the wind farm exchanges energy with the electric network, to which it is connected, at one or more natural frequencies of the electric or mechanical part of the combined system, comprising the wind farm and the network, and the frequency of the exchanged energy is below the fundamental frequency of the system. This oscillatory phenomenon may cause severe damage in the wind farm, if not prevented. Therefore, this book studies the SSR phenomenon in a capacitive series compensated wind farm. A DFIG-based wind farm, which is connected to a series compensated transmission line, is considered as a case study. The book consists of two main parts: Small-signal modeling of DFIG for SSR analysis: This part presents a step-by-step tutorial on modal analysis of a DFIG-based series compensated wind farm using Matlab/Simulink. The model of the system includes wind turbine aerodynamics, a 6th order induction generator, a 2nd order two-mass shaft system, a 4th order series compensated transmission line, a 4th order rotor-side converter (RSC) controller and a 4th order grid-side converter (GSC) controller, and a 1st order DC-link model. The relevant modes are identified using participation factor analysis. Definition of the SSR in DFIG-based wind farms: This part mainly focuses on the identification and definition of the main types of SSR that occur in DFIG wind farms, namely: (1) induction generator effect (SSIGE), (2) torsional interactions (SSTI), and (3) control interactions (SSCI).

Download or read book Modeling and Analysis of Doubly Fed Induction Generator Wind Energy Systems written by Lingling Fan and published by Academic Press. This book was released on 2015-04-16 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: Wind Energy Systems: Modeling, Analysis and Control with DFIG provides key information on machine/converter modelling strategies based on space vectors, complex vector, and further frequency-domain variables. It includes applications that focus on wind energy grid integration, with analysis and control explanations with examples. For those working in the field of wind energy integration examining the potential risk of stability is key, this edition looks at how wind energy is modelled, what kind of control systems are adopted, how it interacts with the grid, as well as suitable study approaches. Not only giving principles behind the dynamics of wind energy grid integration system, but also examining different strategies for analysis, such as frequency-domain-based and state-space-based approaches. Focuses on real and reactive power control Supported by PSCAD and Matlab/Simulink examples Considers the difference in control objectives between ac drive systems and grid integration systems

Download or read book Wind Power in Power Systems written by Thomas Ackermann and published by John Wiley & Sons. This book was released on 2012-04-23 with total page 1132 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of the highly acclaimed Wind Power in Power Systems has been thoroughly revised and expanded to reflect the latest challenges associated with increasing wind power penetration levels. Since its first release, practical experiences with high wind power penetration levels have significantly increased. This book presents an overview of the lessons learned in integrating wind power into power systems and provides an outlook of the relevant issues and solutions to allow even higher wind power penetration levels. This includes the development of standard wind turbine simulation models. This extensive update has 23 brand new chapters in cutting-edge areas including offshore wind farms and storage options, performance validation and certification for grid codes, and the provision of reactive power and voltage control from wind power plants. Key features: Offers an international perspective on integrating a high penetration of wind power into the power system, from basic network interconnection to industry deregulation; Outlines the methodology and results of European and North American large-scale grid integration studies; Extensive practical experience from wind power and power system experts and transmission systems operators in Germany, Denmark, Spain, UK, Ireland, USA, China and New Zealand; Presents various wind turbine designs from the electrical perspective and models for their simulation, and discusses industry standards and world-wide grid codes, along with power quality issues; Considers concepts to increase penetration of wind power in power systems, from wind turbine, power plant and power system redesign to smart grid and storage solutions. Carefully edited for a highly coherent structure, this work remains an essential reference for power system engineers, transmission and distribution network operator and planner, wind turbine designers, wind project developers and wind energy consultants dealing with the integration of wind power into the distribution or transmission network. Up-to-date and comprehensive, it is also useful for graduate students, researchers, regulation authorities, and policy makers who work in the area of wind power and need to understand the relevant power system integration issues.

Download or read book 2019 IEEE Sustainable Power and Energy Conference iSPEC written by IEEE Staff and published by . This book was released on 2019-11-21 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Parallel with the IEEE PES General Meeting in North America every summer, iSPEC will be held in China every winter

Download or read book Power Converter of Electric Machines Renewable Energy Systems and Transportation written by Adolfo Dannier and published by MDPI. This book was released on 2021-09-02 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power converters and electric machines represent essential components in all fields of electrical engineering. In fact, we are heading towards a future where energy will be more and more electrical: electrical vehicles, electrical motors, renewables, storage systems are now widespread. The ongoing energy transition poses new challenges for interfacing and integrating different power systems. The constraints of space, weight, reliability, performance, and autonomy for the electric system have increased the attention of scientific research in order to find more and more appropriate technological solutions. In this context, power converters and electric machines assume a key role in enabling higher performance of electrical power conversion. Consequently, the design and control of power converters and electric machines shall be developed accordingly to the requirements of the specific application, thus leading to more specialized solutions, with the aim of enhancing the reliability, fault tolerance, and flexibility of the next generation power systems.

Download or read book Applied Power and Energy Technology II written by Hong Bo Fan and published by Trans Tech Publications Ltd. This book was released on 2014-08-13 with total page 1660 pages. Available in PDF, EPUB and Kindle. Book excerpt: Collection of selected, peer reviewed papers from the 2014 2nd International Conference on Advances in Energy and Environmental Science (ICAEES 2014), June 21-22, 2014, Guangzhou, China. The 297 papers are grouped as follows: Chapter 1: Development and Utilization of Solar Energy, Chapter 2: Development and Utilization of Biomass Energy, Chapter 3: Development and Utilization of Wind Energy, Chapter 4: Nuclear Energy and Other Energy, Chapter 5: Energy Chemical Engineering and Fuel Cell, Chapter 6: New Energy Vehicles and Electric Vehicles, Chapter 7: Power System, Automation and Control, Chapter 8: High Voltage and Insulation Technology, Chapter 9: Power Electronics, Chapter 10: Smart Grid Technology and Intelligent Technology, Chapter 11: Power Systems Management, Chapter 12: Engineering Thermodynamics and Thermal Engineering, Chapter 13: Power Machinery and Engineering, Chapter 14: HVACR and Heat Pumps, Chapter 15: Equipment Design, Manufacturing and Automation, Chapter 16: Building Materials and Constructions, Green and Energy-Efficient Buildings, Applied Mechanics, Chapter 17: Development and Management of the Energy and Resources Industry, Chapter 18: Computer and Information Technologies Applications, Mathematical Modeling for Industry Development, Chapter 19: Engineering and Engineering Management Education

Download or read book Advances in Power and Energy Engineering written by Yuanzhang Sun and published by CRC Press. This book was released on 2016-04-05 with total page 724 pages. Available in PDF, EPUB and Kindle. Book excerpt: Energy and power are playing pivotal roles in social and economic developments of the modern world. Energy and power engineers and technologists have made our lives much more comfortable and affordable. However, due to the demands of the global population on resources and the environment, innovations of more reliable and sustainable energy res

Download or read book Computational Intelligence Cyber Security and Computational Models Models and Techniques for Intelligent Systems and Automation written by Geetha Ganapathi and published by Springer. This book was released on 2018-09-10 with total page 255 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the proceedings of the Third International Conference on Computational Intelligence, Cyber Security, and Computational Models, ICC3 2017, which was held in Coimbatore, India, in December 2017. The 15 papers presented in this volume were carefully reviewed and selected from 63 submissions. They were organized in topical sections named: computational intelligence; cyber security; and computational models.

Download or read book Renewable Energy Technologies written by Nayan Kumar and published by John Wiley & Sons. This book was released on 2022-09-27 with total page 676 pages. Available in PDF, EPUB and Kindle. Book excerpt: RENEWABLE ENERGY TECHNOLOGIES With the goal of accelerating the growth of green energy utilization for the sustainability of life on earth, this volume, written and edited by a global team of experts, goes into the practical applications that can be utilized across multiple disciplines and industries, for both the engineer and the student. Green energy resources are gaining more attention in academia and industry as one of the preferred choices for sustainable energy conversion. Due to the energy demand, environmental impacts, economic needs, and social issues, green energy resources are being researched, developed, and funded more than ever before. Researchers are facing numerous challenges, but there are new opportunities waiting for green energy resource utilization within the context of environmental and economic sustainability. Efficient energy conversion from solar, wind, biomass, fuel cells, and others are paramount to this overall mission and the success of these efforts. Written and edited by a global team of experts, this groundbreaking new volume from Scrivener Publishing presents recent advances in the study of green energy across a variety of fields and sources. Various applications of green energy resources, modeling and performance analysis, and grid integration aspects of green energy resources are considered. Not only laying out the concepts in an easy-to-understand way, but this team offers the engineer, scientist, student, or other professional practical solutions to everyday problems in their daily applications. Valuable as a learning tool for beginners in this area as well as a daily reference for engineers and scientists working in these areas, this is a must-have for any library.

Download or read book Advanced Control and Optimization Paradigms for Wind Energy Systems written by Radu-Emil Precup and published by Springer. This book was released on 2019-02-07 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents advanced studies on the conversion efficiency, mechanical reliability, and the quality of power related to wind energy systems. The main concern regarding such systems is reconciling the highly intermittent nature of the primary source (wind speed) with the demand for high-quality electrical energy and system stability. This means that wind energy conversion within the standard parameters imposed by the energy market and power industry is unachievable without optimization and control. The book discusses the rapid growth of control and optimization paradigms and applies them to wind energy systems: new controllers, new computational approaches, new applications, new algorithms, and new obstacles.

Download or read book Power Systems Operation with 100 Renewable Energy Sources written by Sanjeevikumar Padmanaban and published by Elsevier. This book was released on 2023-11-08 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power Systems Operation with 100% Renewable Energy Sources combines fundamental concepts of renewable energy integration into power systems with real-world case studies to bridge the gap between theory and implementation. The book examines the challenges and solutions for renewable energy integration into the transmission and distribution grids, and also provides information on design, analysis and operation. Starting with an introduction to renewable energy sources and bulk power systems, including policies and frameworks for grid upgradation, the book then provides forecasting, modeling and analysis techniques for renewable energy sources. Subsequent chapters discuss grid code requirements and compliance, before presenting a detailed break down of solar and wind integration into power systems. Other topics such as voltage control and optimization, power quality enhancement, and stability control are also considered. Filled with case studies, applications and techniques, Power Systems Operation with 100% Renewable Energy Sources is a valuable read to researchers, students and engineers working towards more sustainable power systems. Explains Volt/Var control and optimization for both transmission grid and distribution Discusses renewable energy integration into the weak grid system, along with its challenges, examples, and case studies Offers simulation examples of renewable energy integration studies that readers will perform using advanced simulation tools Presents recent trends like energy storage systems and demand responses for improving stability and reliability

Download or read book Smart Solar PV Inverters with Advanced Grid Support Functionalities written by Rajiv K. Varma and published by John Wiley & Sons. This book was released on 2021-12-01 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: Learn the fundamentals of smart photovoltaic (PV) inverter technology with this insightful one-stop resource Smart Solar PV Inverters with Advanced Grid Support Functionalities presents a comprehensive coverage of smart PV inverter technologies in alleviating grid integration challenges of solar PV systems and for additionally enhancing grid reliability. Accomplished author Rajiv Varma systematically integrates information from the wealth of knowledge on smart inverters available from EPRI, NREL, NERC, SIWG, EU-PVSEC, CIGRE, IEEE publications; and utility experiences worldwide. The book further presents a novel, author-developed and patented smart inverter technology for utilizing solar PV plants both in the night and day as a Flexible AC Transmission System (FACTS) Controller STATCOM, named PV-STATCOM. Replete with case studies, this book includes over 600 references and 280 illustrations. Smart Solar PV Inverters with Advanced Grid Support Functionalities’ features include: Concepts of active and reactive power control; description of different smart inverter functions, and modeling of smart PV inverter systems Distribution system applications of PV-STATCOM for dynamic voltage control, enhancing connectivity of solar PV and wind farms, and stabilization of critical motors Transmission system applications of PV-STATCOM for improving power transfer capacity, power oscillation damping (POD), suppression of subsynchronous oscillations, mitigation of fault induced delayed voltage recovery (FIDVR), and fast frequency response (FFR) with POD Hosting capacity for solar PV systems, its enhancement through effective settings of different smart inverter functions; and control coordination of smart PV inverters Emerging smart inverter grid support functions and their pioneering field demonstrations worldwide, including Canada, USA, UK, Chile, China, and India. Perfect for system planners and system operators, utility engineers, inverter manufacturers and solar farm developers, this book will prove to be an important resource for academics and graduate students involved in electrical power and renewable energy systems.

Download or read book Emerging Power Converters for Renewable Energy and Electric Vehicles written by Md. Rabiul Islam and published by CRC Press. This book was released on 2021-05-30 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers advancements of power electronic converters and their control techniques for grid integration of large-scale renewable energy sources and electrical vehicles. Major emphasis is on transformer-less direct grid integration, bidirectional power transfer, compensation of grid power quality issues, DC system protection and grounding, interaction in mixed AC/DC systems, AC and DC system stability, design of high-frequency high power density systems with advanced soft magnetic materials, modeling and simulation of mixed AC/DC systems, switching strategies for enhanced efficiency, and protection and reliability for sustainable grid integration. This book is an invaluable resource for professionals active in the field of renewable energy and power conversion. Md. Rabiul Islam received his PhD from the University of Technology Sydney (UTS), Australia. He was appointed as a Lecturer at Rajshahi University of Engineering & Technology (RUET) in 2005 and promoted to full-term Professor in 2017. In early 2018, he joined the School of Electrical, Computer, and Telecommunications Engineering, University of Wollongong, Australia. He is a Senior Member of IEEE. His research interests include the fields of power electronic converters, renewable energy technologies, power quality, electrical machines, electric vehicles, and smart grids. He has authored or coauthored more than 200 publications including 50 IEEE Transactions/IEEE Journal papers. He has been serving as an editor for IEEE Transactions on Energy Conversion and IEEE Power Engineering Letters, and associate editor for IEEE Access. Md. Rakibuzzaman Shah is a Senior Lecturer with the School of Engineering, Information Technology and Physical Science at Federation University Australia. He has worked and consulted with distribution network operators and transmission system operators on individual projects and has done collaborative work on a large number of projects (EPSRC project on multi-terminal HVDC, Scottish and Southern Energy multi-infeed HVDC) - primarily on the dynamic impact of integrating new technologies and power electronics into large systems. He is an active member of the IEEE and CIGRE. He has more than 70 international publications and has spoken at the leading power system conferences around the world. His research interests include future power grids (i.e., renewable energy integration, wide-area control), asynchronous grid connection through VSC-HVDC, application of data mining in power system, distribution system energy management, and low carbon energy systems. Mohd. Hasan Ali is currently an Associate Professor with the Electrical and Computer Engineering Department at the University of Memphis, USA, where he leads the Electric Power and Energy Systems (EPES) Laboratory. His research interests include advanced power systems, smart-grid and microgrid systems, renewable energy systems, and cybersecurity issues in modern power grids. Dr. Ali has more than 190 publications, including 2 books, 4 book chapters, 2 patents, 60 top ranked journal papers, 96 peer-reviewed international conference papers, and 20 national conference papers. He serves as the editor of the IEEE Transactions on Sustainable Energy and IET-Generation, Transmission and Distribution (GTD) journal. Dr. Ali is a Senior Member of the IEEE Power and Energy Society (PES). He is also the Chair of the PES of the IEEE Memphis Section.

Download or read book Power System Modelling and Scripting written by Federico Milano and published by Springer Science & Business Media. This book was released on 2010-09-08 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power system modelling and scripting is a quite general and ambitious title. Of course, to embrace all existing aspects of power system modelling would lead to an encyclopedia and would be likely an impossible task. Thus, the book focuses on a subset of power system models based on the following assumptions: (i) devices are modelled as a set of nonlinear differential algebraic equations, (ii) all alternate-current devices are operating in three-phase balanced fundamental frequency, and (iii) the time frame of the dynamics of interest ranges from tenths to tens of seconds. These assumptions basically restrict the analysis to transient stability phenomena and generator controls. The modelling step is not self-sufficient. Mathematical models have to be translated into computer programming code in order to be analyzed, understood and “experienced”. It is an object of the book to provide a general framework for a power system analysis software tool and hints for filling up this framework with versatile programming code. This book is for all students and researchers that are looking for a quick reference on power system models or need some guidelines for starting the challenging adventure of writing their own code.

Download or read book Modeling and Stability Analysis of Inverter Based Resources written by Lingling Fan and published by CRC Press. This book was released on 2023-11-29 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: Renewable energy sources interface with the ac grids via inverters and are termed inverter-based resources (IBRs). They are replacing traditional fossil fuel-based synchronous generators at a dazzling speed. In turn, unprecedented dynamic events have occurred, threatening power grid reliability. Modeling and Stability Analysis of Inverter-Based Resources provides a fundamental understanding of IBR dynamics. Developing reliability solutions requires a thorough understanding of challenges, and in this case, IBR-associated dynamics. Modeling and stability analysis play an indispensable role in revealing a mechanism of dynamics. This book covers the essential techniques of dynamic model building for IBRs, including type-3 wind farms, type-4 wind farms, and solar photovoltaics. Besides modeling, this book offers readers the techniques of stability analysis. The text includes three parts. Part 1 concentrates on tools, including electromagnetic transient simulation, analysis, and measurement-based modeling. Part 2 focuses on IBR modeling and analysis details. Part 3 highlights generalized dynamic circuit representation—a unified modeling framework for dynamic and harmonic analysis. This topic of IBR dynamic modeling and stability analysis is interesting, challenging, and intriguing. The authors have led the effort of publishing the 2020 IEEE Power and Energy Society’s TR-80 taskforce report “Wind Energy Systems Subsynchronous Oscillations: Modeling and Events,” and the two taskforce papers on investigation of real-world IBR dynamic events. In this book, the authors share with readers many insights into modeling and analysis for real-world IBR dynamic events investigation.

Download or read book Handbook Of Renewable Energy Technology written by Zobaa Ahmed F and published by World Scientific. This book was released on 2011-01-26 with total page 876 pages. Available in PDF, EPUB and Kindle. Book excerpt: Effects of environmental, economic, social, political and technical factors have led to the rapid deployment of various sources of renewable energy-based power generation. The incorporation of these generation technologies have led to the development of a broad array of new methods and tools to integrate this new form of generation into the power system network. This book, arranged into six sections, highlights various renewable energy based generation technologies, and consists a series of papers written by experts in their respective fields of specialization.The Handbook of Renewable Energy Technology will be of great practical benefit to professionals, scientists and researchers in the relevant industries, and will be of interest to those of the general public wanting to know more about renewable energy technologies.

Download or read book Issues in Renewable Energy Technologies 2013 Edition written by and published by ScholarlyEditions. This book was released on 2013-05-01 with total page 1182 pages. Available in PDF, EPUB and Kindle. Book excerpt: Issues in Renewable Energy Technologies / 2013 Edition is a ScholarlyEditions™ book that delivers timely, authoritative, and comprehensive information about Hydrologic Engineering. The editors have built Issues in Renewable Energy Technologies: 2013 Edition on the vast information databases of ScholarlyNews.™ You can expect the information about Hydrologic Engineering in this book to be deeper than what you can access anywhere else, as well as consistently reliable, authoritative, informed, and relevant. The content of Issues in Renewable Energy Technologies: 2013 Edition has been produced by the world’s leading scientists, engineers, analysts, research institutions, and companies. All of the content is from peer-reviewed sources, and all of it is written, assembled, and edited by the editors at ScholarlyEditions™ and available exclusively from us. You now have a source you can cite with authority, confidence, and credibility. More information is available at http://www.ScholarlyEditions.com/.