Download or read book Analog Delta Sigma Modulators with Reduced Sensitivity to Circuit Non idealities written by Roger Alan Levinson and published by . This book was released on 1988 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Continuous Time Delta Sigma Modulators for High Speed A D Conversion written by James A. Cherry and published by Springer Science & Business Media. This book was released on 2006-04-18 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Among analog-to-digital converters, the delta-sigma modulator has cornered the market on high to very high resolution converters at moderate speeds, with typical applications such as digital audio and instrumentation. Interest has recently increased in delta-sigma circuits built with a continuous-time loop filter rather than the more common switched-capacitor approach. Continuous-time delta-sigma modulators offer less noisy virtual ground nodes at the input, inherent protection against signal aliasing, and the potential to use a physical rather than an electrical integrator in the first stage for novel applications like accelerometers and magnetic flux sensors. More significantly, they relax settling time restrictions so that modulator clock rates can be raised. This opens the possibility of wideband (1 MHz or more) converters, possibly for use in radio applications at an intermediate frequency so that one or more stages of mixing might be done in the digital domain. Continuous-Time Delta-Sigma Modulators for High-Speed A/D Conversion: Theory, Practice and Fundamental Performance Limits covers all aspects of continuous-time delta-sigma modulator design, with particular emphasis on design for high clock speeds. The authors explain the ideal design of such modulators in terms of the well-understood discrete-time modulator design problem and provide design examples in Matlab. They also cover commonly-encountered non-idealities in continuous-time modulators and how they degrade performance, plus a wealth of material on the main problems (feedback path delays, clock jitter, and quantizer metastability) in very high-speed designs and how to avoid them. They also give a concrete design procedure for a real high-speed circuit which illustrates the tradeoffs in the selection of key parameters. Detailed circuit diagrams, simulation results and test results for an integrated continuous-time 4 GHz band-pass modulator for A/D conversion of 1 GHz analog signals are also presented. Continuous-Time Delta-Sigma Modulators for High-Speed A/D Conversion: Theory, Practice and Fundamental Performance Limits concludes with some promising modulator architectures and a list of the challenges that remain in this exciting field.
Download or read book Top Down Design of High Performance Sigma Delta Modulators written by Fernando Medeiro and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 303 pages. Available in PDF, EPUB and Kindle. Book excerpt: The interest for :I:~ modulation-based NO converters has significantly increased in the last years. The reason for that is twofold. On the one hand, unlike other converters that need accurate building blocks to obtain high res olution, :I:~ converters show low sensitivity to the imperfections of their building blocks. This is achieved through extensive use of digital signal pro cessing - a desirable feature regarding the implementation of NO interfaces in mainstream CMOS technologies which are better suited for implementing fast, dense, digital circuits than accurate analog circuits. On the other hand, the number of applications with industrial interest has also grown. In fact, starting from the earliest in the audio band, today we can find :I:~ converters in a large variety of NO interfaces, ranging from instrumentation to commu nications. These advances have been supported by a number of research works that have lead to a considerably large amount of published papers and books cov ering different sub-topics: from purely theoretical aspects to architecture and circuit optimization. However, so much material is often difficultly digested by those unexperienced designers who have been committed to developing a :I:~ converter, mainly because there is a lack of methodology. In our view, a clear methodology is necessary in :I:~ modulator design because all related tasks are rather hard.
Download or read book Delta Sigma Data Converters written by Steven R. Norsworthy and published by Wiley-IEEE Press. This book was released on 1997 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive guide offers a detailed treatment of the analysis, design, simulation and testing of the full range of today's leading delta-sigma data converters. Written by professionals experienced in all practical aspects of delta-sigma modulator design, Delta-Sigma Data Converters provides comprehensive coverage of low and high-order single-bit, bandpass, continuous-time, multi-stage modulators as well as advanced topics, including idle-channel tones, stability, decimation and interpolation filter design, and simulation.
Download or read book Continuous Time Sigma Delta Modulation for A D Conversion in Radio Receivers written by Lucien Breems and published by Springer Science & Business Media. This book was released on 2006-04-18 with total page 165 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text describes the design and theory of continuous-time sigma-delta modulators for analogue-to-digital conversion in radio receivers. The book's main focus is on dynamic range, linearity and power efficiency aspects of sigma-delta modulators, which are very important requirements for use in battery operated receivers.
Download or read book Oversampling Delta Sigma Data Converters written by James C. Candy and published by John Wiley & Sons. This book was released on 1991-09-02 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt: This now famous anthology brings together various aspects of oversampling methods and compares and evaluates design approaches. It describes the theoretical analysis of converter performances, the actual design of converters and their simulation, circuit implementations, and applications.
Download or read book Sigma Delta Converters Practical Design Guide written by Jose M. de la Rosa and published by John Wiley & Sons. This book was released on 2018-11-05 with total page 581 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thoroughly revised and expanded to help readers systematically increase their knowledge and insight about Sigma-Delta Modulators Sigma-Delta Modulators (SDMs) have become one of the best choices for the implementation of analog/digital interfaces of electronic systems integrated in CMOS technologies. Compared to other kinds of Analog-to-Digital Converters (ADCs), Σ∆Ms cover one of the widest conversion regions of the resolution-versus-bandwidth plane, being the most efficient solution to digitize signals in an increasingly number of applications, which span from high-resolution low-bandwidth digital audio, sensor interfaces, and instrumentation, to ultra-low power biomedical systems and medium-resolution broadband wireless communications. Following the spirit of its first edition, Sigma-Delta Converters: Practical Design Guide, 2nd Edition takes a comprehensive look at SDMs, their diverse types of architectures, circuit techniques, analysis synthesis methods, and CAD tools, as well as their practical design considerations. It compiles and updates the current research reported on the topic, and explains the multiple trade-offs involved in the whole design flow of Sigma-Delta Modulators—from specifications to chip implementation and characterization. The book follows a top-down approach in order to provide readers with the necessary understanding about recent advances, trends, and challenges in state-of-the-art Σ∆Ms. It makes more emphasis on two key points, which were not treated so deeply in the first edition: It includes a more detailed explanation of Σ∆Ms implemented using Continuous-Time (CT) circuits, going from system-level synthesis to practical circuit limitations. It provides more practical case studies and applications, as well as a deeper description of the synthesis methodologies and CAD tools employed in the design of Σ∆ converters. Sigma-Delta Converters: Practical Design Guide, 2nd Edition serves as an excellent textbook for undergraduate and graduate students in electrical engineering as well as design engineers working on SD data-converters, who are looking for a uniform and self-contained reference in this hot topic. With this goal in mind, and based on the feedback received from readers, the contents have been revised and structured to make this new edition a unique monograph written in a didactical, pedagogical, and intuitive style.
Download or read book Analog Circuit Design written by Willy M.C. Sansen and published by Springer Science & Business Media. This book was released on 1999-10-31 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume of Analog Circuit Design concentrates on three topics: (X)DSL and other communication systems; RF MOST models; and integrated filters and oscillators. The book comprises five chapters on the first topic with six each on the other two, all written by internationally recognized experts. They are tutorial in nature and together make a substantial contribution to improving the design of analog circuits. The book is divided into three parts: Part I: (X)DSL and other Communication Systems presents some examples of recent improved modem techniques which have resulted in much higher transmission speeds over the local telephone network. It also presents components for the implementation of different standards. Part II: RF MOST Models investigates the state of the art in RF MOST models. It compares the existing BSIM3v3, Philips' Model 9 and the EKV model with respect to their capability to accurately predict GHz performance with submicron CMOST technologies. It shows how it has now become quite feasible to model a MOST at very high frequencies, giving rise to an increased use of MOST technologies in RF applications. Part III: Integrated Filters and Oscillators illustrates how the increasing use of communication tools goes hand-in-hand with the design of analog filters and oscillators with greater flexibility and higher bandwidth.
Download or read book Continuous Time Sigma Delta A D Conversion written by Friedel Gerfers and published by Springer Science & Business Media. This book was released on 2006-02-27 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sigma-delta A/D converters are a key building block in wireless and multimedia applications. This comprehensive book deals with all relevant aspects arising during the analysis, design and simulation of the now widespread continuous-time implementations of sigma-delta modulators. The results of several years of research by the authors in the field of CT sigma-delta modulators are covered, including the analysis and modeling of different CT modulator architectures, CT/DT loop filter synthesis, a detailed error analysis of all components, and possible compensation/correction schemes for the non-ideal behavior in CT sigma-delta modulators. Guidance for obtaining low-power consumption and several practical implementations are also presented. It is shown that all the proposed new theories, architectures and possible correction techniques have been confirmed by measurements on discrete or integrated circuits. Quantitative results are also provided, thus enabling prediction of the resulting accuracy.
Download or read book A Fast 1 bit Delta sigma Modulator for Analog to digital Conversion written by David J. Block and published by . This book was released on 1991 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analog Circuit Design written by Johan Huijsing and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 447 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many interesting design trends are shown by the six papers on operational amplifiers (Op Amps). Firstly. there is the line of stand-alone Op Amps using a bipolar IC technology which combines high-frequency and high voltage. This line is represented in papers by Bill Gross and Derek Bowers. Bill Gross shows an improved high-frequency compensation technique of a high quality three stage Op Amp. Derek Bowers improves the gain and frequency behaviour of the stages of a two-stage Op Amp. Both papers also present trends in current-mode feedback Op Amps. Low-voltage bipolar Op Amp design is presented by leroen Fonderie. He shows how multipath nested Miller compensation can be applied to turn rail-to-rail input and output stages into high quality low-voltage Op Amps. Two papers on CMOS Op Amps by Michael Steyaert and Klaas Bult show how high speed and high gain VLSI building blocks can be realised. Without departing from a single-stage OT A structure with a folded cascode output, a thorough high frequency design technique and a gain-boosting technique contributed to the high-speed and the high-gain achieved with these Op Amps. . Finally. Rinaldo Castello shows us how to provide output power with CMOS buffer amplifiers. The combination of class A and AB stages in a multipath nested Miller structure provides the required linearity and bandwidth.
Download or read book The Design of Low Voltage Low Power Sigma Delta Modulators written by Shahriar Rabii and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: Oversampling techniques based on sigma-delta modulation are widely used to implement the analog/digital interfaces in CMOS VLSI technologies. This approach is relatively insensitive to imperfections in the manufacturing process and offers numerous advantages for the realization of high-resolution analog-to-digital (A/D) converters in the low-voltage environment that is increasingly demanded by advanced VLSI technologies and by portable electronic systems. In The Design of Low-Voltage, Low-Power Sigma-Delta Modulators, an analysis of power dissipation in sigma-delta modulators is presented, and a low-voltage implementation of a digital-audio performance A/D converter based on the results of this analysis is described. Although significant power savings can typically be achieved in digital circuits by reducing the power supply voltage, the power dissipation in analog circuits actually tends to increase with decreasing supply voltages. Oversampling architectures are a potentially power-efficient means of implementing high-resolution A/D converters because they reduce the number and complexity of the analog circuits in comparison with Nyquist-rate converters. In fact, it is shown that the power dissipation of a sigma-delta modulator can approach that of a single integrator with the resolution and bandwidth required for a given application. In this research the influence of various parameters on the power dissipation of the modulator has been evaluated and strategies for the design of a power-efficient implementation have been identified. The Design of Low-Voltage, Low-Power Sigma-Delta Modulators begins with an overview of A/D conversion, emphasizing sigma-delta modulators. It includes a detailed analysis of noise in sigma-delta modulators, analyzes power dissipation in integrator circuits, and addresses practical issues in the circuit design and testing of a high-resolution modulator. The Design of Low-Voltage, Low-Power Sigma-Delta Modulators will be of interest to practicing engineers and researchers in the areas of mixed-signal and analog integrated circuit design.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Oata Analysis and Synthesis (CINOAS) * at Purdue. University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 33 (thesis year 1988) a total of 13,273 theses titles from 23 Canadian and 1 85 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 33 reports theses submitted in 1988, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.
Download or read book Analog Circuit Design written by Rudy J. van de Plassche and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 403 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the extended and revised editions of all the talks of the ninth AACD Workshop held in Hotel Bachmair, April 11 - 13 2000 in Rottach-Egem, Germany. The local organization was managed by Rudolf Koch of Infineon Technologies AG, Munich, Germany. The program consisted of six tutorials per day during three days. Experts in the field presented these tutorials and state of the art information is communicated. The audience at the end of the workshop selects program topics for the following workshop. The program committee, consisting of Johan Huijsing of Delft University of Technology, Willy Sansen of Katholieke Universiteit Leuven and Rudy van de Plassche of Broadcom Netherlands BV Bunnik elaborates the selected topics into a three-day program and selects experts in the field for presentation. Each AACD Workshop has given rise to publication of a book by Kluwer entitled "Analog Circuit Design". A series of nine books in a row provides valuable information and good overviews of all analog circuit techniques concerning design, CAD, simulation and device modeling. These books can be seen as a reference to those people involved in analog and mixed signal design. The aim of the workshop is to brainstorm on new and valuable design ideas in the area of analog circuit design. It is the hope of the program committee that this ninth book continues the tradition of emerging contributions to the design of analog and mixed signal systems in Europe and the rest of the world.
Download or read book How to Improve Performance of Sigma Delta Analog to Digital Converter written by Prateek Verma and published by LAP Lambert Academic Publishing. This book was released on 2015-04-02 with total page 92 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog to Digital Converters are widely used in the field of VLSI and are mainly used in the applications like audio, instrumentation, seismic, voice etc which requires higher value of resolution. For such applications, ADC's can be used based on Nyquist Rate modulators (where sampling is done with twice the sampling frequency) or Sigma-Delta modulators (where sampling is done with 15-20 times the sampling frequency). ADC based on sigma-delta modulators is attractive for VLSI implementation because they are not so sensitive of circuit non-idealities and component mismatch. However, issues such as clock jitter and excess loop delay become great challenges to the designer, especially at high sampling frequency. Special design should be applied to overcome these problems. Sigma-Delta modulator can be of different orders like 1st order, 2nd order etc and can be continuous time (less power consumption) or Discrete Time. This book demonstrates a Graphical User Interface (GUI) of 2nd order Sigma-Delta modulator which is used to check the non-idealities of the circuit. Here the model is based on the behavioral modeling of the parameters with the help of Matlab- Simulink.
Download or read book Oversampled Delta Sigma Modulators written by Mücahit Kozak and published by Springer Science & Business Media. This book was released on 2007-05-08 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt: Oversampled Delta-Sigma Modulators: Analysis, Applications, and Novel Topologies presents theorems and their mathematical proofs for the exact analysis of the quantization noise in delta-sigma modulators. Extensive mathematical equations are included throughout the book to analyze both single-stage and multi-stage architectures. It has been proved that appropriately set initial conditions generate tone free output, provided that the modulator order is at least three. These results are applied to the design of a Fractional-N PLL frequency synthesizer to produce spurious free RF waveforms. Furthermore, the book also presents time-interleaved topologies to increase the conversion bandwidth of delta-sigma modulators. The topologies have been generalized for any interleaving number and modulator order. The book is full of design and analysis techniques and contains sufficient detail that enables readers with little background in the subject to easily follow the material in it.
Download or read book Analog Circuits and Devices written by Wai-Kai Chen and published by CRC Press. This book was released on 2003-03-26 with total page 509 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Principles and Application in Engineering Series is a new series of convenient, economical references sharply focused on particular engineering topics and subspecialties. Each volume in this series comprises chapters carefully selected from CRC's bestselling handbooks, logically organized for optimum convenience, and thoughtfully priced to fit
