Download or read book Assessment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2011-06-03 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various combinations of commercially available technologies could greatly reduce fuel consumption in passenger cars, sport-utility vehicles, minivans, and other light-duty vehicles without compromising vehicle performance or safety. Assessment of Technologies for Improving Light Duty Vehicle Fuel Economy estimates the potential fuel savings and costs to consumers of available technology combinations for three types of engines: spark-ignition gasoline, compression-ignition diesel, and hybrid. According to its estimates, adopting the full combination of improved technologies in medium and large cars and pickup trucks with spark-ignition engines could reduce fuel consumption by 29 percent at an additional cost of $2,200 to the consumer. Replacing spark-ignition engines with diesel engines and components would yield fuel savings of about 37 percent at an added cost of approximately $5,900 per vehicle, and replacing spark-ignition engines with hybrid engines and components would reduce fuel consumption by 43 percent at an increase of $6,000 per vehicle. The book focuses on fuel consumption-the amount of fuel consumed in a given driving distance-because energy savings are directly related to the amount of fuel used. In contrast, fuel economy measures how far a vehicle will travel with a gallon of fuel. Because fuel consumption data indicate money saved on fuel purchases and reductions in carbon dioxide emissions, the book finds that vehicle stickers should provide consumers with fuel consumption data in addition to fuel economy information.

Download or read book Gasoline Compression Ignition Technology written by Gautam Kalghatgi and published by Springer Nature. This book was released on 2022-01-17 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on gasoline compression ignition (GCI) which offers the prospect of engines with high efficiency and low exhaust emissions at a lower cost. A GCI engine is a compression ignition (CI) engine which is run on gasoline-like fuels (even on low-octane gasoline), making it significantly easier to control particulates and NOx but with high efficiency. The state of the art development to make GCI combustion feasible on practical vehicles is highlighted, e.g., on overcoming problems on cold start, high-pressure rise rates at high loads, transients, and HC and CO emissions. This book will be a useful guide to those in academia and industry.

Download or read book Automotive Fuels Reference Book written by Paul Richards and published by SAE International. This book was released on 2014-03-05 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first two editions of this title, published by SAE International in 1990 and 1995, have been best-selling definitive references for those needing technical information about automotive fuels. This long-awaited new edition has been thoroughly revised and updated, yet retains the original fundamental fuels information that readers find so useful. This book is written for those with an interest in or a need to understand automotive fuels. Because automotive fuels can no longer be developed in isolation from the engines that will convert the fuel into the power necessary to drive our automobiles, knowledge of automotive fuels will also be essential to those working with automotive engines. Small quantities of fuel additives increasingly play an important role in bridging the gap that often exists between fuel that can easily be produced and fuel that is needed by the ever-more sophisticated automotive engine. This book pulls together in a single, extensively referenced volume, the three different but related topics of automotive fuels, fuel additives, and engines, and shows how all three areas work together. It includes a brief history of automotive fuels development, followed by chapters on automotive fuels manufacture from crude oil and other fossil sources. One chapter is dedicated to the manufacture of automotive fuels and fuel blending components from renewable sources. The safe handling, transport, and storage of fuels, from all sources, are covered. New combustion systems to achieve reduced emissions and increased efficiency are discussed, and the way in which the fuels’ physical and chemical characteristics affect these combustion processes and the emissions produced are included. There is also discussion on engine fuel system development and how these different systems affect the corresponding fuel requirements. Because the book is for a global market, fuel system technologies that only exist in the legacy fleet in some markets are included. The way in which fuel requirements are developed and specified is discussed. This covers test methods from simple laboratory bench tests, through engine testing, and long-term test procedures.

Download or read book Fuel Engine Interactions written by Gautam Kalghatgi and published by SAE International. This book was released on 2013-10-08 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt: Conventional fossil fuels will constitute the majority of automotive fuels for the foreseeable future but will have to adapt to changes in engine technology. Unconventional transport fuels such as biofuels, gas-to-liquid fuels, compressed natural gas, and liquid petroleum gas will also play a role. Hydrogen might be a viable transport fuel if it overcomes barriers in production, transport, storage, and safety and/or if fuel cells become viable. This book opens by considering these issues and then introduces practical transport fuels. A chapter on engine deposits follows, which is an important practical topic about how fuels affect engines that is not usually considered in other books. The next three chapters discuss auto-ignition phenomena in engines. The auto-ignition resistance of fuels is the most important fuel property since it limits the efficiency of spark ignition engines and determines the performance of compression ignition engines. Moreover, the manufacture of fuels is primarily driven by the need to meet auto-ignition quality demands set by fuel specifications. The final chapter considers the implications for future fuels. The book covers the many important ways that fuels and engines interact and why and how fuels will need to change to meet the requirements of future engines, as well as the implications for fuels manufacture and specifications.

Download or read book Alternative Fuels and Advanced Combustion Techniques as Sustainable Solutions for Internal Combustion Engines written by Akhilendra Pratap Singh and published by Springer Nature. This book was released on 2021-05-15 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt: This monograph covers different aspects related to utilization of alternative fuels in internal combustion (IC) engines with a focus on biodiesel, dimethyl ether, alcohols, biogas, etc. The focal point of this book is to present engine combustion, performance and emission characteristics of IC engines fueled by these alternative fuels. A section of this book also covers the potential strategies of utilization of these alternative fuels in an energy efficient manner to reduce the harmful pollutants emitted from IC engines. It presents the comparative analysis of different alternative fuels in a variety of engines to show the appropriate alternative fuel for specific types of engines. This book will prove useful for both researchers as well as energy experts and policy makers.

Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.

Download or read book Cost Effectiveness and Deployment of Fuel Economy Technologies for Light Duty Vehicles written by National Research Council and published by National Academies Press. This book was released on 2015-09-28 with total page 812 pages. Available in PDF, EPUB and Kindle. Book excerpt: The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.

Download or read book Diesel Engine Reference Book written by Bernard Challen and published by Butterworth-Heinemann. This book was released on 1999 with total page 712 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference work covering the design and applications of diesel engines of all sizes. The text uses easily understood language and a practical approach to explore aspects of diesel engineering such as thermodynamics modelling, long-term use, applications and condition monitoring.

Download or read book Proceedings of the 2nd Conference on Engine Processes written by Sens, Marc and published by Universitätsverlag der TU Berlin. This book was released on 2015-10-30 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the combustion engine looks set to remain the dominant energy conversion unit in vehicle powertrains in the medium term, either in combination with electrical components or on its own, attention will need to be paid to continue improving its efficiency in the future. The high development depth of today's combustion engines means that it is becoming increasingly difficult to achieve significant efficiency improvements by simple means. On the search for these improvements, the focus has shifted to inner-engine processes, for instance charge cycles including the charging system, the mixture formation including injection, combustion and kinematic conversion of the energy within the fuel. Our 2nd conference 'Engine processes' aims to offer all developers a platform to discuss the latest technological developments in the field of inner-engine process control, and encourage new paths to be taken. We believe that the program for this conference is a sound foundation for this endeavour. Da der Verbrennungsmotor auch mittelfristig die dominierende Energiewandlungseinheit im Antriebsstrang von Kraftfahrzeugen sein wird, entweder im Verbund mit elektrischen Komponenten oder aber als alleiniger Antrieb, muss der Verbesserung von dessen Wirkungsgrad auch in Zukunft erhebliche Aufmerksamkeit zu Teil werden. Aufgrund der hohen Entwicklungstiefe, die heutige Verbrennungsmotoren aufweisen, wird es immer schwerer, deutliche Wirkungsgradverbesserungen auf einfachem Weg zu erreichen. Auf der Suche nach diesen Verbesserungen rücken die innermotorischen Prozesse immer mehr in den Fokus, hierzu zählen der Ladungswechsel inkl. Aufladesystem, die Gemischbildung inkl. Einspritzung, die Verbrennung sowie die kinematische Wandlung der im Kraftstoff gebundenen Energie. Unsere 2. Tagung „Motorische Prozesse“ soll nun allen Entwicklern als Austauschforum zu neuesten technologischen Entwicklungen auf dem Gebiet der innermotorischen Prozessführung dienen und dazu anregen neue Wege zu beschreiten. Wir sind überzeugt, mit dem vorliegenden Tagungs-Programm hierzu einen sehr guten Beitrag leisten zu können.

Download or read book Energy Research Abstracts written by and published by . This book was released on 1986 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Proceedings of the 5th International Conference on Industrial Engineering ICIE 2019 written by Andrey A. Radionov and published by Springer Nature. This book was released on 2019-11-30 with total page 1257 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights recent findings in industrial, manufacturing and mechanical engineering, and provides an overview of the state of the art in these fields, mainly in Russia and Eastern Europe. A broad range of topics and issues in modern engineering are discussed, including the dynamics of machines and working processes, friction, wear and lubrication in machines, surface transport and technological machines, manufacturing engineering of industrial facilities, materials engineering, metallurgy, control systems and their industrial applications, industrial mechatronics, automation and robotics. The book gathers selected papers presented at the 5th International Conference on Industrial Engineering (ICIE), held in Sochi, Russia in March 2019. The authors are experts in various fields of engineering, and all papers have been carefully reviewed. Given its scope, the book will be of interest to a wide readership, including mechanical and production engineers, lecturers in engineering disciplines, and engineering graduates.

Download or read book Advanced Combustion Technologies for Low Carbon Emissions written by Jun Li and published by Frontiers Media SA. This book was released on 2023-07-10 with total page 119 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Biomass Processing for Biofuels Bioenergy and Chemicals written by Wei-Hsin Chen and published by MDPI. This book was released on 2020-05-23 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biomass can be used to produce renewable electricity, thermal energy, transportation fuels (biofuels), and high-value functional chemicals. As an energy source, biomass can be used either directly via combustion to produce heat or indirectly after it is converted to one of many forms of bioenergy and biofuel via thermochemical or biochemical pathways. The conversion of biomass can be achieved using various advanced methods, which are broadly classified into thermochemical conversion, biochemical conversion, electrochemical conversion, and so on. Advanced development technologies and processes are able to convert biomass into alternative energy sources in solid (e.g., charcoal, biochar, and RDF), liquid (biodiesel, algae biofuel, bioethanol, and pyrolysis and liquefaction bio-oils), and gaseous (e.g., biogas, syngas, and biohydrogen) forms. Because of the merits of biomass energy for environmental sustainability, biofuel and bioenergy technologies play a crucial role in renewable energy development and the replacement of chemicals by highly functional biomass. This book provides a comprehensive overview and in-depth technical research addressing recent progress in biomass conversion processes. It also covers studies on advanced techniques and methods for bioenergy and biofuel production.

Download or read book Dual Fuel Diesel Engines written by Ghazi A. Karim and published by CRC Press. This book was released on 2015-03-02 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dual-Fuel Diesel Engines offers a detailed discussion of different types of dual-fuel diesel engines, the gaseous fuels they can use, and their operational practices. Reflecting cutting-edge advancements in this rapidly expanding field, this timely book:Explains the benefits and challenges associated with internal combustion, compression ignition,

Download or read book Renewable Fuels written by Jacqueline O'Connor and published by Cambridge University Press. This book was released on 2022-11-30 with total page 583 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive text on renewable fuels- key to a net-zero carbon future. Detailing how they are made and used, including case-studies.

Download or read book Thermal Energy written by Yatish T. Shah and published by CRC Press. This book was released on 2018-01-12 with total page 854 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book details sources of thermal energy, methods of capture, and applications. It describes the basics of thermal energy, including measuring thermal energy, laws of thermodynamics that govern its use and transformation, modes of thermal energy, conventional processes, devices and materials, and the methods by which it is transferred. It covers 8 sources of thermal energy: combustion, fusion (solar) fission (nuclear), geothermal, microwave, plasma, waste heat, and thermal energy storage. In each case, the methods of production and capture and its uses are described in detail. It also discusses novel processes and devices used to improve transfer and transformation processes.

Download or read book Energy Efficiency in Mobility Systems written by Shaharin Anwar Sulaiman and published by Springer Nature. This book was released on 2019-10-03 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights a diverse range of initiatives that have been launched to attain sustainable mobility systems, in particular regarding the energy efficiency aspect. It offers a valuable reference for various stakeholders in transportation systems, while also sharing new ideas on how transportation can meet the challenges of tomorrow.