Download or read book Airdrop of Supplies and Equipment Rigging Airdrop Platforms FM 4 20 102 To 13C7 1 5 written by Department of the Army and published by Createspace Independent Pub. This book was released on 2012-11-02 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this manual, “Airdrop of Supplies and Equipment: Rigging Airdrop Platforms,” is to provide the latest approved procedures for rigging airdrop Platforms. This manual is written for use by the parachute rigger. It consists of 10 chapters. The procedures contained in this manual are typical and serve as the standard from which all platform rigging is derived. Due to the uniqueness of some equipment and items, the procedures in a specific rigging manual may be different from those in this manual. When procedures are different, those in the specific manual will be followed. When an item of equipment is specified to be used for which its minimum or maximum capacity is exceeded, a notice of exception will be printed at the beginning of each paragraph in each rigging manual where the exception is authorized. When an item of airdrop equipment is replaced or a procedure is changed, it will be impossible to change all manuals in the field at one time. Therefore, this manual will be changed, when necessary. Chapters 1 through 10 contain specific limitations and general information about the rigging of airdrop platform loads for low-velocity airdrop from US aircraft and also shows and tells how to prepare, attach, and safety tie some of the components and systems used in the specific rigging manuals of the FM 4-20.100/TO 13C7 series.

Download or read book Airdrop of Supplies and Equipment written by Department of the Army and published by Createspace Independent Publishing Platform. This book was released on 2017-09-04 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Airdrop of Supplies and Equipment: Rigging Containers" (TM 4-48.03/MCRP 4-11.3C/TO 13C7-1-11/FM 4-20) provides doctrinal guidance and direction for United States Army, United States Marine Corps, and United States Air Force units conducting aerial delivery operations. This manual provides information on how to prepare and rig airdrop containers. The three types of airdrop by which container loads can be delivered are low-velocity airdrop, high-velocity airdrop, and free drop. The purpose of this manual is to provide the latest approved procedures for rigging Aerial Delivery Containers. This manual is written for use by the parachute rigger, jumpmaster, and Low-Cost Low-Altitude, Aerial Delivery System certified personnel.

Download or read book Field Manual FM 4 20 102 Airdrop of Supplies and Equipment Rigging Airdrop Platforms June 2006 MCRP 4 11 3J US Army written by United States Government Us Army and published by CreateSpace. This book was released on 2012-06-06 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: FM 4-20.102, MCRP 4-11.3J, NAVSEA SS400-AB-MMO-010, TO 13C7-1-5 The purpose of this manual is to provide the latest approved procedures for rigging airdrop Platforms. This manual is written for use by the parachute rigger. It consists of 10 chapters. The procedures contained in this manual are typical and serve as the standard from which all platform rigging is derived. Due to the uniqueness of some equipment and items, the procedures in a specific rigging manual may be different from those in this manual. When procedures are different, those in the specific manual will be followed. When an item of equipment is specified to be used for which its minimum or maximum capacity is exceeded, a notice of exception will be printed at the beginning of each paragraph in each rigging manual where the exception is authorized. When an item of airdrop equipment is replaced or a procedure is changed, it will be impossible to change all manuals in the field at one time. Therefore, this manual will be changed, when necessary. Chapters 1 through 10 contain specific limitations and general information about the rigging of airdrop platform loads for low-velocity airdrop from US aircraft and also shows and tells how to prepare, attach, and safety tie some of the components and systems used in the specific rigging manuals of the FM 4-20.100/TO 13C7 series. Note: New information concerning the Extraction Parachute Jettison System (EPJS) has been added along with some new procedures for the extraction force transfer coupling (EFTC). The C-141 and C-5 aircraft have been taken out and the C-17 aircraft information has been added. Also, a new user friendly format has been introduced combining general information and rigging information in each chapter.

Download or read book Airdrop of Supplies and Equipment Dual Row Airdrop Systems Volume II FM 4 20 105 2 to 13C7 1 51 VOL II written by Department of the Army and published by Createspace Independent Pub. This book was released on 2012-11-02 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this manual, “Airdrop of Supplies and Equipment: Dual Row Airdrop Systems – Volume II,” is to provide the latest approved procedures for rigging Dual Row Airdrop System (DRAS) platforms. This manual is written for use by the parachute rigger. The procedures contained in this manual are typical and serve as the standard from which all DRAS platform rigging is derived. Due to the uniqueness of some equipment and items, the procedures in a specific rigging chapter may be different from those in chapters 1 and 2. When procedures are different, those in the specific chapter will be followed. When an item of equipment is specified to be used for which its minimum or maximum capacity is exceeded, a notice of exception will be printed at the beginning of each paragraph in each rigging chapter where the exception is authorized. Chapters 1 and 2 contain specific limitations and general information about the rigging of DRAS airdrop platform loads for low-velocity airdrop from the C-17 (Globemaster) aircraft, shows and tells how to prepare, attach, and safety tie some of the components and systems used in the specific rigging chapters of FM 420.105-2/TO 13C7-1-51 VOL II.

Download or read book FM 4 20 102 Airdrop of Supplies and Equipment written by U S Army and published by . This book was released on 2021-04-17 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this manual is to provide the latest approved procedures for rigging airdrop Platforms. This manual is written for use by the parachute rigger. It consists of 10 chapters.The procedures contained in this manual are typical and serve as the standard from which all platform rigging is derived. Due to the uniqueness of some equipment and items, the procedures in a specific rigging manual may be different from those in this manual. When procedures are different, those in the specific manual will be followed. When an item of equipment is specified to be used for which its minimum or maximum capacity is exceeded, a notice of exception will be printed at the beginning of each paragraph in each rigging manual where the exception is authorized. When an item of airdrop equipment is replaced or a procedure is changed, it will be impossible to change all manuals in the field at one time. Therefore, this manual will be changed, when necessary.

Download or read book Airdrop of Supplies and Equipment Rigging Containers FM 4 20 103 MCRP 4 11 3C To 13C7 1 11 written by Department of the Army and published by Createspace Independent Pub. This book was released on 2012-11-30 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual, “Airdrop of Supplies and Equipment: Rigging Containers (FM 4-20.103),” provides the latest approved doctrine for rigging airdrop containers. It is written for use by a parachute rigger or jumpmaster. Container loads are loads that are rigged for airdrop in airdrop containers such as the A-7A airdrop cargo sling assembly, the A-21 cargo bag assembly, and the A-22 cargo bag assembly. These containers are packed with supplies, disassembled equipment, or small items of ready-to-use equipment prepared for airdrop. Loads may be required to be cushioned with energy dissipating material (honeycomb), felt, or cellulose wadding depending on the load requirements and the method of airdrop. The number and types of parachutes required to stabilize the load and slow its descent depend on the type of container used, the weight of the load, and the type of airdrop. This manual consists of six parts. a. Part one contains general information for container loads and aircraft. b. Part two contains procedures for rigging A-7A container loads. c. Part three contains procedures for rigging A-21 container loads. d. Part four contains procedures for rigging A-22 container loads. e. Part five contains procedures for rigging low-cost aerial delivery systems. f. Part six contains procedures for rigging specialized loads and equipment.

Download or read book Airdrop of Supplies and Equipment written by Department of the Army and published by Createspace Independent Publishing Platform. This book was released on 2017-09-04 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Airdrop of Supplies And Equipment: Rigging 5-Ton Trucks," (TM 4-48.06/FM 10-526), provides doctrinal guidance on the approved procedures on how to prepare and rig a 5-ton cargo truck on a 24-foot, type V airdrop platform with six G-11C cargo parachutes and other items of airdrop equipment to be delivered by low-velocity airdrop from C-130 or C-17 aircraft. The principal audience for TM 4-48.06 is all members of the profession of arms. Commanders and staffs of Army headquarters serving as joint task force or multinational headquarters should also refer to applicable joint or multinational doctrine concerning the range of military operations and joint or multinational forces. Trainers and educators throughout the Army and the Air Force will also use this publication.

Download or read book Airdrop of Supplies and Equipment Rigging 105 Millimeter Howitzers FM 4 20 119 To 13C7 10 31 written by Department of the Army and published by Createspace Independent Pub. This book was released on 2012-11-28 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual shows how to rig the M102, M119, and M101A1 105-millimeter howitzers for low-velocity airdrop from a C-130 or C-17 aircraft. The manual includes procedures and equipment for rigging the M102 and M119 105-millimeter howitzer with the 1 ¼-ton High Mobility Multipurpose Wheeled Vehicle (HMMWV) truck as the prime mover on a 32-foot, type V airdrop platform for low-velocity airdrop from a C-130 or C-17 aircraft. In addition, procedures are given for rigging two M119 105-millimeter howitzers on a single platform with two different ammunition loads and with two 81-millimeter mortars for a low-velocity airdrop from C-130 or C-17 aircraft. The manual is designed for use by all parachute riggers.

Download or read book Airdrop of Supplies and Equipment Rigging Typical Supply Loads FM 4 20 112 To 13C7 1 8 written by Department Army and published by CreateSpace. This book was released on 2012-11-28 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual tells and shows how to prepare and rig mass supply loads. Procedures are given for typical loads that can be contained by the methods shown. These procedures are meant as a guide, and may be adapted to specific loads. Procedures are also given for some specific ammunition loads. This manual is designed for all parachute riggers.

Download or read book Airdrop of Supplies and Equipment written by Department of the Army and published by . This book was released on 2017-08-17 with total page 210 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual, FM 4-20.116, "Airdrop of Supplies and Equipment: Reference Data for Airdrop Platform Loads," provides a ready-reference planning guide for loads rigged for airdrop. It illustrates the rigged load and contains dimensional data, weight, and center of balance (CB) for each load. Information is also provided on aircraft, extraction parachutes and reference tables of miscellaneous information on materials used to fabricate and maintain air items and to rig airdrop equipment

Download or read book Airdrop of supplies and equipment written by United States. Department of the Army and published by . This book was released on 1975 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Airdrop of Supplies and Equipment Reference Data for Airdrop Platform Loads FM 4 20 116 To 13C7 1 13 written by Department of the Army and published by Createspace Independent Pub. This book was released on 2012-11-02 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual, “Airdrop of Supplies and Equipment: Reference Data for Airdrop Platform Loads,” provides a ready-reference planning guide for loads rigged for airdrop. It illustrates the rigged load and contains dimensional data, weight, and center of balance (CB) for each load. Information is also provided on aircraft, extraction parachutes and reference tables of miscellaneous information on materials used to fabricate and maintain air items and to rig airdrop equipment. The information in this manual may be used to compute aircraft requirements and to assist the rigger and loadmaster during joint inspection of airdrop loads. The publication containing the procedure for preparing and rigging each load is indicated with the data for the load.

Download or read book Airdrop of Supplies and Equipment written by United States. Department of the Army and published by . This book was released on 1975 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Airdrop of Supplies and Equipment written by United States. Department of the Army and published by . This book was released on 1976 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Airdrop of Supplies and Equipment Dual Row Airdrop Systems Volume I FM 4 20 105 1 to 13C7 1 51 VOL I written by Department Army and published by CreateSpace. This book was released on 2012-11-28 with total page 446 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this manual is to provide the latest approved procedures for rigging Dual Row Airdrop System (DRAS) platforms. This manual is written for use by the parachute rigger. The procedures contained in this manual are typical and serve as the standard from which all DRAS platform rigging is derived.

Download or read book Airdrop of Supplies and Equipment written by Department of the Army and published by Createspace Independent Publishing Platform. This book was released on 2017-09-04 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual, "Airdrop of Supplies and Equipment: Rigging Communication Control Vehicles" (FM 10-500-23), tells and shows how to prepare and rig the Mobile Microwave Landing System (MMLS) which is packed in 11 hard-shell protective cases. The cases are rigged with four 3kw generators and four fuel cans in the beds of an M998 HMMWV truck and an M116A2 3/4-ton trailer. The load is rigged on a 24-foot, type V platform with three G-11 cargo parachutes for low-velocity airdrop from a C-130, C-141, C-5, and C-17. The Standard Intergraded Command Post System (SICPS) and the Common Hardware/Software 2nd Generation Package (CHS-2) are rigged on a 20-foot, type V airdrop platform with three G-11 cargo parachutes for low-velocity airdrop from a C-130, C-141, C-5, and C-17. The M996 CAV is rigged on a 20-foot, type V airdrop platform for low-velocity airdrop from a C-130, C-141, C- 5, and C-17. The load requires three G-11 cargo parachutes. The CAV is rigged with communication equipment. The M998 cargo/troop carrier (two seater) is rigged with a radio equipment GRC/206 Air Force pallet. Other equipment included on the load is the 1.5-kilowatt, 28-VDC generator set, two cable spools, two 5-gallon fuel cans, and one 5-gallon water can. The load requires two G-ll cargo parachutes and is rigged for low-velocity airdrop from a C-130, C-141, C-5, and C-17. The M998 cargo/troop carrier (four seater), is rigged with a radio equipment GRC/206 Air Force pallet. Other equipment included on the load is one cable spool, two 5-gallon fuel cans, one 5-gallon water can, one roll of field wire, one set of slave cables, and one camouflage net with support poles. Also included with this load are one shovel, one ax, two sets of antennas, 2 quarts of oil, 1 quart of transmission fluid, one funnel, and one fuel nozzle. The truck weighs 6,020 pounds with 3/4 tank of fuel and equipment installed. The load requires two G-ll cargo parachutes and is rigged for low velocity airdrop from a C-130, C-141, C-5, and C-17.

Download or read book Airdrop of Supplies and Equipment Rigging Airborne Crane Shovel and Attachments FM 10 548 To 13C7 24 21 written by Department Army and published by CreateSpace. This book was released on 2012-11-12 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual is designed for use by all parachute riggers. It tells and shows how to rig the following cranes: a) The 7-Ton Airborne Crane-Shovel. The 7-ton airborne crane-shovel is rigged for low-velocity airdrop from a C-130 or a C-141 aircraft, b) The 3/8- Cubic Yard Crane-Shovel Attachments. The 3/8-cubic yard crane-shovel attachments are rigged for low-velocity airdrop from a C-130 or a C-141 aircraft, c) The Koehring 7 ½-Ton Crane. The Koehring 7 ½-ton crane is rigged for low-velocity airdrop from C-130 or a C-141 aircraft. It is also rigged for LAPE airdrop from a C-130 aircraft.