Download or read book Advanced Nanostructured Electrode and Materials Design for Zinc Air Batteries written by Jordan Scott and published by . This book was released on 2013 with total page 89 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zinc air batteries have great promise as a new age energy storage device due to their environmental benignity, high energy density in terms of both mass and volume, and low cost Zinc air batteries get their high energy density by using oxygen from the air as the active material. This means that all the mass and volume that are normally required for active material in a battery are replaced by a thin gas diffusion electrode which allows for oxygen from the air to diffuse into the cell. Although this seems ideal, there are many technical challenges associated with the cell being open to the atmosphere. Some of these issues include electrolyte and electrode drying out, poor reaction kinetics involving sluggish reaction, the need for bifunctional catalysts to charge and discharge, and durability of the gas diffusion electrode itself. The bifuntional catalysts used in these systems are often platinum or other precious metals since these are commonly known to have the highest performance, however the inherent cost of these materials limits the feasibility of zinc air systems. Thus, there is a need to limit or remove the necessity for platinum carbon catalysts. There are many types of non precious metal catalysts which can be used in place of platinum, however their performance is often not as high, and the durability of these catalysts is also weak. Similar limitations on feasibility are invoked by the poor durability of the gas diffusion electrodes. Carbon corrosion occurs at the harsh caustic conditions present at the gas diffusion electrodes, and this corrosion causes catalyst dissolution. Moreover, many issues with zinc electrode fabrication limit durability and usable anode surface area within these systems. There is a need for a stable, porous, high surface area anode with good structural integrity. These issues are addressed in this work by three studies which each focuses on solving some of the issues pertaining to a crucial component of zinc air batteries, those being the gas diffusion electrode, the zinc electrode, and the bifunctional catalyst necessary for oxygen reduction reactions (ORR) and oxygen evolution reactions (OER).
Download or read book Zinc Air Batteries written by Zongping Shao and published by John Wiley & Sons. This book was released on 2023-01-04 with total page 309 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zinc–Air Batteries Authoritative and comprehensive resource covering foundational knowledge of zinc–air batteries as well as their practical applications Zinc–Air Batteries provides a comprehensive understanding of the history and development of Zn–air batteries, with a systematic overview of components, design, and device innovation, along with recent advances in the field, especially with regards to the cathode catalyst design made by cutting-edge materials, engineering processes, and technologies. In particular, design principles regarding the key components of Zn–air batteries, ranging from air cathode, to zinc anode, and to electrolyte, are emphasized. Furthermore, industrial developments of Zn–air batteries are discussed and emerging new designs of Zn–air batteries are also introduced. The authors argue that designing advanced Zn–air battery technologies is important to the realization of efficient energy storage and conversion—and, going further, eventually holds the key to a sustainable energy future and a carbon-neutral goal. Edited and contributed to by leading professionals and researchers in the field, Zinc–Air Batteries also contains information regarding: Design of oxygen reduction catalysts in primary zinc–air batteries, including precious metals, single-atoms, carbons, and transition metal oxides Design of bifunctional oxygen catalysts in rechargeable zinc–air batteries, covering specific oxygen redox reactions and catalyst candidates Design of three-dimensional air cathode in zinc–air batteries, covering loading of carbon-based and transition metal catalysts, plus design of the three-phase interface Design of electrolyte for zinc–air batteries, including liquid electrolytes (e.g., alkaline) and gel polymer electrolytes (e.g., PVA hydrogel) For students, researchers, and instructors working in battery technologies, materials science, and electrochemistry, and for industry and government representatives for decision making associated with energy and transportation, Zinc–Air Batteries summarizes the research results on Zn–air batteries and thereby helps researchers and developers to implement the technology in practice.
Download or read book Novel Design and Synthesis of Nanostructured Electrode Materials for Advanced Lithium Ion Batteries written by Zhiqiang Xie and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Metal Oxide Based Nanostructured Electrocatalysts for Fuel Cells Electrolyzers and Metal Air Batteries written by Teko Napporn and published by Elsevier. This book was released on 2021-01-30 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Oxide-Based Nanostructured Electrocatalysts for Fuel Cells, Electrolyzers, and Metal-Air Batteries is a comprehensive book summarizing the recent overview of these new materials developed to date. The book is motivated by research that focuses on the reduction of noble metal content in catalysts to reduce the cost associated to the entire system. Metal oxides gained significant interest in heterogeneous catalysis for basic research and industrial deployment. Metal Oxide-Based Nanostructured Electrocatalysts for Fuel Cells, Electrolyzers, and Metal-Air Batteries puts these opportunities and challenges into a broad context, discusses the recent researches and technological advances, and finally provides several pathways and guidelines that could inspire the development of ground-breaking electrochemical devices for energy production or storage. Its primary focus is how materials development is an important approach to produce electricity for key applications such as automotive and industrial. The book is appropriate for those working in academia and R&D in the disciplines of materials science, chemistry, electrochemistry, and engineering. Includes key aspects of materials design to improve the performance of electrode materials for energy conversion and storage device applications Reviews emerging metal oxide materials for hydrogen production, hydrogen oxidation, oxygen reduction and oxygen evolution Discusses metal oxide electrocatalysts for water-splitting, metal-air batteries, electrolyzer, and fuel cell applications
Download or read book Nanomaterials in Advanced Batteries and Supercapacitors written by Kenneth I. Ozoemena and published by Springer. This book was released on 2016-07-18 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an authoritative source of information on the use of nanomaterials to enhance the performance of existing electrochemical energy storage systems and the manners in which new such systems are being made possible. The book covers the state of the art of the design, preparation, and engineering of nanoscale functional materials as effective catalysts and as electrodes for electrochemical energy storage and mechanistic investigation of electrode reactions. It also provides perspectives and challenges for future research. A related book by the same editors is: Nanomaterials for Fuel Cell Catalysis.
Download or read book Advanced Nanomaterials for Electrochemical Energy Conversion and Storage written by and published by Elsevier. This book was released on 2019-11-14 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Nanomaterials for Electrochemical Energy Conversion and Storage covers recent progress made in the rational design and engineering of functional nanomaterials for battery and supercapacitor applications in the forms of electrode materials, separators and electrolytes. The book includes detailed discussions of preparation methods, structural characterization, and manipulation techniques. Users will find a comprehensive illustration on the close correlation between material structures and properties, such as energy density, power density, cycle number and safety. Provides an overview on the application of nanomaterials for energy storage and power systems Includes a description of the fundamental aspects of the electrochemical process Explores the new aspects of electrolyte and separator systems
Download or read book Nanotechnology in Advanced Electrochemical Power Sources written by S. R. S. Prabaharan and published by CRC Press. This book was released on 2014-10-24 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt: The challenge of providing adequate power on an indefinite basis without causing long-term damage to the environment requires a versatile means of energy conversion and storage. As such, electrical energy storage is becoming more vital today than at any time in human history. Electrochemical systems, such as batteries, supercapacitors, fuel cells, and photoelectrochemical cells, can help meet this objective. Future generations of rechargeable lithium batteries will be required to power portable electronic devices, store electricity from renewable sources, and serve as a vital component to pursuing electric mobility in the future to reduce fossil fuel demand and mitigate environmental issues. In this context, engineering of new materials, especially at the nanoscale, has become imperative to achieve enhanced energy and power density to meet the future challenges of energy storage. This book outlines the state of the art of nanoscale aspects of advanced energy storage devices, such as lithium-ion batteries, including microbatteries and electrochemical supercapacitors. It focuses on various fundamental issues related to device performance of various positive and negative electrode materials, with special reference to their nanoscale advantages. It also includes fundamentals and processing techniques with regard to synthesis, characterization, physical, and electrochemical properties, and applications of nanoscale materials pertaining to advanced electrochemical power sources. A variety of advanced nanomaterials, such as transition metal oxides, phosphates, silicates, and conversion electrodes, together with some special nanomaterials such as carbon nanotubes, nanorods, and mesoporous carbons are discussed by many notable authorities in the field.
Download or read book Nano Enhanced and Nanostructured Polymer Based Membranes for Energy Applications written by Maria Giovanna Buonomenna and published by Woodhead Publishing. This book was released on 2022-01-22 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt: There is a growing need for better membranes in several emerging application fields especially those related to energy conversion and storage as well as to water treatment and recycling. Processability, is an important functional property, often ignored, especially in the early discovery phase for new materials, but it should be one of the most important properties, that needs to be considered in the development of better membrane materials. Useful membrane materials have to be capable of being formed into thin membranes, in particular for membrane gas separation, water treatment and desalination, and then packaged, into large area membrane modules. All gas separation membranes that are in current commercial use are based on polymers, which are solution-processable. This book intends to deal with composite, in most cases hybrid polymer-based membranes for three separate application fields: energy conversion, energy storage and water treatment and recovery. Each chapter will explain clearly the various membrane processes then go on to discuss in detail the corresponding advanced membranes used. The logic that lies behind this is that you have to understand the process in order to develop new high-performance membranes. By taking this approach, the author aims to overcome the disconnection that currently exists between membrane materials scientists and industrial process engineers. Discusses interdisciplinary content by a single author, approaching synthesis and development of materials from the perspective of their processability Describes the novel aspects of membrane science that is related to energy storage, conversion and wastewater treatment Presents an emphasis on scientific results which have an impact on real applications in terms of renewable and clean energy challenges
Download or read book Synthesis of Functional Nanomaterials for Electrochemical Energy Storage written by Huan Pang and published by Springer Nature. This book was released on 2020-07-08 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive review of functional nanomaterials for electrochemical applications, presenting interesting examples of nanomaterials with different dimensions and their applications in electrochemical energy storage. It also discusses the synthesis of functional nanomaterials, including quantum dots; one-dimensional, two-dimensional and three-dimensional nanostructures; and advanced nanocomposites. Highlighting recent advances in current electrochemical energy storage hotpots: lithium batteries, lithium-ion batteries, sodium-ion batteries, other metal-ion batteries, halogen ion batteries, and metal–gas batteries, this book will appeal to readers in the various fields of chemistry, material science and engineering.
Download or read book Material Design and Engineering for Polymer Electrolyte Membrane Zinc air Batteries written by Jing Fu and published by . This book was released on 2018 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zinc-air batteries, whose advantages include relatively high energy density (1218 Wh kg-1), abundance of zinc in earth's crust, and very safe operational characteristics, are promising for applications in consumer electronics, electrified transportation, grid storage, and other fields. At the moment, primary zinc-air batteries are produced for low-drain electronic gadgets such as hearing aids. However, secondary (i.e., electrically rechargeable) zinc-air batteries have eluded widespread adoption due mainly to the slow reaction kinetics of oxygen evolution at the air electrode during recharge. A bifunctional oxygen electrocatalyst that can recharge the batteries more efficiently is required. Moreover, in the presence of aqueous alkaline electrolytes, zinc-air batteries suffer from low durability and performance loss due mainly to the formation of zinc dendrites during charging, the loss of aqueous electrolytes, the detachment of the catalyst layer and the precipitation of carbonates at the air electrode. These persistent issues have motivated a shift in electrolyte design towards efficient hydroxide ion-conductive polymeric electrolytes. A combination of efficient bifunctional oxygen electrocatalysts and polymeric electrolyte improvements may enable zinc-air batteries to be implemented in widespread applications in flexible/lightweight electronic devices and electric vehicles. In this work, I present a feasible strategy combining material innovations with engineering methods to develop a new type of zinc-air battery, i.e., a flexible, rechargeable polymer electrolyte membrane zinc-air battery (PEMZAB). In the first study, a proof of concept of a film-shaped, rechargeable PEMZAB was conducted by using a KOH-doped poly(vinyl alcohol) (PVA) gel electrolyte, porous zinc electrode and bifunctional air electrode comprising a commercial Co3O4 nanoparticles-loaded carbon cloth. Then, a novel hydroxide ion-conductive polymeric electrolyte membrane and an efficient bifunctional oxygen zinc-air battery performance. Specifically, highly quaternaized cellulose nanofibers were synthesized to produce a hydroxide ion-conductive electrolyte membrane (referred to as QAFC). The QAFC membrane shows advantages of a high ionic conductivity of 21.2 mS cm-1, good chemical stability, mechanical robustness and flexibility, and inhibition of zinc dendrites and carbonations. In addition to the QAFC electrolyte membrane development, a hybrid bifunctional oxygen electrocatalyst, consisting of cobalt oxysulfide nanoparticles and nitrogen-doped graphene nanomeshes (CoO0.87S0.13/GN), was prepared. The defect chemistries of both oxygen-vacancy-rich cobalt oxysulfides and edge-nitrogen-rich graphene nanomeshes lead to a remarkable improvement in electrocatalytic performance, where CoO0.87S0.13/GN exhibits strongly comparable catalytic activity and much better stability than the best-known benchmark noble metal catalysts. A simple, water-based filtration method for a direct assembly of the QAFC membrane and the CoO0.87S0.13/GN catalyst film was demonstrated with the PEMZAB. Such a fabrication approach enables intimate contact between the solid-solid catalyst-electrolyte interfaces for facile charge transfer. Moreover, benefiting from the performance improvement of the QAFC electrolyte membrane and the CoO0.87S0.13/GN bifunctional catalyst, the resulting battery possesses a higher energy density of 857.9 Wh kg-1 and a more stable cycling performance, over 300 hours of operation at 20 mA cm-2 under ambient conditions, than those of a battery using PVA-KOH gel electrolyte and commercial Co3O4 bifunctional catalysts. In the last study, the knowledge gained from the hybrid CoO0.87S0.13/GN bifunctional catalyst is transferred to the fabrication of a hybrid catalyst/current collector assembly for the bifunctional air electrode. In this assembly, a hair-like array of mesoporous cobalt oxide nanopetals in nitrogen-doped carbon nanotubes is grown directly on a stainless-steel mesh through chemical vapor deposition and electrodeposition methods. Such integrative design not only ensures a large number of catalytically active sites in a given electrode surface, but also increases the electron transfer between each individual catalyst and the conductive substrate. This advanced air electrode assembly further boosts the PEMZAB performance, with a high peak power density of 160.7 mW cm-2 at 250 mA cm-2 and a remarkable cycling durability: lasting over 600 hours of operation at 25 mA cm-2 under ambient conditions.
Download or read book Advanced Battery Materials written by Chunwen Sun and published by John Wiley & Sons. This book was released on 2019-03-26 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electrochemical energy storage has played important roles in energy storage technologies for portable electronics and electric vehicle applications. During the past thirty years, great progress has been made in research and development of various batteries, in term of energy density increase and cost reduction. However, the energy density has to be further increased to achieve long endurance time. In this book, recent research and development in advanced electrode materials for electrochemical energy storage devices are presented, including lithium ion batteries, lithium-sulfur batteries and metal-air batteries, sodium ion batteries and supercapacitors. The materials involve transition metal oxides, sulfides, Si-based material as well as graphene and graphene composites.
Download or read book Nanostructured Materials written by Zesheng Li and published by Elsevier. This book was released on 2023-08-31 with total page 592 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanostructured Materials: Physicochemical Chemistry Fundamentals for Energy and Environmental Applications summarizes research knowledge and helps advanced students, researchers and industrial technicians understand specific applications of nanomaterials in energy and the environment. Sections bring a strong foundational focus on the physicochemical basis of nanomaterials for these applications, the basic theory and physicochemical basis of nanomaterials, an energy and environment applications examination of typical cases, and progress. This book will appeal to researchers in the chemical sciences (inorganic and physical chemistry, coordination chemistry, molecular dynamics, electrochemistry, photocatalysis, thermocatalysis, thermodynamics, etc.), nanoscience (graphene, carbon nanotubes, nanocrystals, nano catalysis, energy, and environment-nano science), and more. Efficient use of energy, eco-friendly environmental systems, and technologies play an important role in global sustainable development. Multifunctional nanocomposites have excellent properties and can meet the practical needs of energy development and environmental treatment. They have been gradually applied in chemical materials, energy preparation, pollution control and other fields and have achieved impressive development. Provides a unified overview of a large variety of different applications on the design and synthesis of nanomaterials with potential applications in various conventional and new energy and environmental technologies Provides a strong foundational focus on the analysis of the structure of nanomaterials, the basic principles of design (nanomaterial structure-activity relationship), and the theoretical basis of physical chemistry (theoretical basis of nanomaterial design and applications) Meets a need to summarize and examine ongoing research and advances in a rapidly developing field
Download or read book Nanostructured Spinel Oxides as Bi functional Electrocatalysts for Rechargeable Metal air Batteries written by Dong Un Lee and published by . This book was released on 2017 with total page 125 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to continuously increasing energy demands, particularly with the emergence of electric vehicles (EV), smart energy grids, and portable electronics, advanced energy conversion and storage systems such as fuel-cells and metal-air batteries have drawn tremendous research and industrial attention. Even though the lithium-ion battery technology is the most developed and widely distributed energy device for a wide range of applications, some researchers view its energy density insufficient for fulfilling the ultimate requirements of highly energy intensive applications such as EVs. Recently, zinc-air batteries have re-gained research attention since the initial development in the 1970s due to their remarkably highly energy density and the potential to be electrically rechargeable. However, some technological hurdles such as low charge/discharge energy efficiency, and insufficient cycle stability have hampered commercialization and introduction of rechargeable zinc-air batteries to the market. The mentioned hurdles are currently the main challenges of rechargeable zinc-air battery developed, and they stem from the fact that the reaction kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are intrinsically very sluggish. The two are the main electrochemical reactions that govern the charge and discharge processes of a rechargeable metal-air battery at the air electrode, and these oxygen reactions must be facilitated by active electrocatalysts in order to progress them at practically viable and stable rates. Currently, the best known catalysts for ORR and OER are carbon supported platinum (Pt/C) and iridium (Ir/C), respectively. However, the use of these precious metal based catalysts for large scale applications like EVs and energy storage systems is prohibitively expensive. Additionally, the durability of these catalysts have been reported to be insufficient for long-term usage under normal device operating conditions. Perhaps most importantly, the precious metal based catalysts are strongly active towards only one of the two oxygen reactions required for rechargeable applications. For example, Pt/C is a strong ORR active catalyst, while Ir/C is a strong OER active catalyst. Recently in the literature, a simple physical mixture of these two catalysts have been used to render bi-functionality, but this method is very rudimentary and still requires two separate syntheses for each catalyst. This suggests that future bi-functionally active catalysts must not only be non-precious (inexpensive), but also a single active material capable of catalyzing both ORR and OER over the same active surface. Having said above, non-precious catalyst research, specifically for bi-functional ORR and OER electrocatalyses, has increased dramatically beginning in the 90's with a very popular and positive belief in the energy community that rechargeable lithium-air batteries could potentially replace lithium-ion batteries. This wave of interest has also picked up research in rechargeable zinc-air batteries since the electrochemical oxygen reactions that take place at the air electrodes are fundamentally very similar. Additionally, the use of zinc metal as the anode, which is one of Earth's most abundant elements, and the water-based (aqueous) solutions as the electrolyte (as opposed to organic ones) made the rechargeable zinc-air battery development very attractive and seemingly easy to scale-up. Moreover, primary (non-rechargeable) zinc-air batteries have already been commercialized and are available in the market as hearing aid batteries, leading many researchers to believe that a simple tuning of the current technology would lead to a successful secondary (rechargeable) zinc-air battery development. However, there are a set of technical difficulties specific to rechargeable zinc-air batteries that have slowed the development for the past few decades. Therefore, the work presented in this thesis aims to address the challenges of rechargeable zinc-air batteries particularly from the active bi-functional electrocatalyst standpoint to make them as commercially viable as possible.
Download or read book Advanced Bifunctional Electrochemical Catalysts for Metal Air Batteries written by Yan-Jie Wang and published by CRC Press. This book was released on 2018-12-14 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal-air batteries (MABs) have attracted attention because of their high specific energy, low cost, and safety features. This book discusses science and technology including material selection, synthesis, characterization, and their applications in MABs. It comprehensively describes various composite bifunctional electrocatalysts, corrosion/oxidation of carbon-containing air cathode catalysts, and how improvements can be achieved in the catalytic activities of oxygen reduction reaction and oxygen evolution reaction and their durability/stability. This book also analyzes, compares, and discusses composite bifunctional electrocatalysts in the applications of MABs, matching the fast information of commercial MABs in requirements. Aimed at researchers and industry professionals, this comprehensive work provides readers with an appreciation for what bifunctional composite electrocatalysts are capable of, how this field has grown in the past decades, and how bifunctional composite electrocatalysts can significantly improve the performance of MABs. It also offers suggestions for future research directions to overcome technical challenges and further facilitate research and development in this important area.
Download or read book Functional Materials For Next generation Rechargeable Batteries written by Jiangfeng Ni and published by World Scientific. This book was released on 2021-02-10 with total page 229 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over-consumption of fossil fuels has caused deficiency of limited resources and environmental pollution. Hence, deployment and utilization of renewable energy become an urgent need. The development of next-generation rechargeable batteries that store more energy and last longer has been significantly driven by the utilization of renewable energy.This book starts with principles and fundamentals of lithium rechargeable batteries, followed by their designs and assembly. The book then focuses on the recent progress in the development of advanced functional materials, as both cathode and anode, for next-generation rechargeable batteries such as lithium-sulfur, sodium-ion, and zinc-ion batteries. One of the special features of this book is that both inorganic electrode materials and organic materials are included to meet the requirement of high energy density and high safety of future rechargeable batteries. In addition to traditional non-aqueous rechargeable batteries, detailed information and discussion on aqueous batteries and solid-state batteries are also provided.
Download or read book Sustainable Materials for Next Generation Energy Devices written by Kuan Yew Cheong and published by Elsevier. This book was released on 2020-12-01 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainable Materials for Next Generation Energy Devices: Challenges and Opportunities presents the latest state-of-the-art knowledge and innovation related to environmentally-friendly functional materials that can be developed for, and employed in, producing a feasible next generation of energy storage and conversion devices. The book is broken up into three sections, covering Energy Storage, Energy Conversion and Advanced Concepts. It will be an important reference for researchers, engineers and students who want to gain extensive knowledge in green and/or sustainable functional materials and their applications. Provides a concise resource for readers interested in sustainable and green functional materials for energy conversion and storage devices Emphasizes sustainable and green concepts in the design of energy devices based on renewable functional materials Presents a survey of both the challenges and opportunities available for renewable functional materials in the development of energy devices
Download or read book Zinc Batteries written by Rajender Boddula and published by John Wiley & Sons. This book was released on 2020-05-05 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Battery technology is constantly changing, and the concepts and applications of these changes are rapidly becoming increasingly more important as more and more industries and individuals continue to make “greener” choices in their energy sources. As global dependence on fossil fuels slowly wanes, there is a heavier and heavier importance placed on cleaner power sources and methods for storing and transporting that power. Battery technology is a huge part of this global energy revolution. Zinc batteries are an advantageous choice over lithium-based batteries, which have dominated the market for years in multiple areas, most specifically in electric vehicles and other battery-powered devices. Zinc is the fourth most abundant metal in the world, which is influential in its lower cost, making it a very attractive material for use in batteries. Zinc-based batteries have been around since the 1930s, but only now are they taking center stage in the energy, automotive, and other industries. Zinc Batteries: Basics, Developments, and Applicationsis intended as a discussion of the different zinc batteries for energy storage applications. It also provides an in-depth description of various energy storage materials for Zinc (Zn) batteries. This book is an invaluable reference guide for electrochemists, chemical engineers, students, faculty, and R&D professionals in energy storage science, material science, and renewable energy.
