Download or read book A Study of Dynamic Loads on Straight Spur Gear Teeth written by Paul Jay Umberger and published by . This book was released on 1968 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt: The dynamic loads acting on gear teeth are very complex. To better understand dynamic loads, this research was carried out with the objectives of measuring experimentally dynamic loads and the frictional forces between gear teeth in mesh. By using strain gages mounted on the sides of the teeth, the transverse component of the dynamic load was measured and is shown for all phases of contact. Using the transverse component at the pitch radius, the dynamic load ratios were computed and found to be substantially lower than predicted by the Buckingham equation. However, sufficient information for evaluating the frictional force was not obtained and further research will be required to evaluate the radial component of the dynamic load. (Author).
Download or read book An Analytical and Experimental Study of Dynamic Loads on Spur Gear Teeth written by Romualdas Kasuba and published by . This book was released on 1962 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Dynamic Loads on Gear Teeth written by Earle Buckingham and published by . This book was released on 1931 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Investigation of the Dynamic Loads in Spur gear Teeth written by John Sinclaire Howland and published by . This book was released on 1962 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Predicted Effect of Dynamic Load on Pitting Fatigue Life for Low contact ratio Spur Gears written by David G. Lewicki and published by . This book was released on 1986 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: How dynamic load affects the surface pitting fatigue life of external spur gears was predicted by using NASA computer program TELSGE. Parametric studies were performed over a range of various gear parameters modeling low-contact-ratio involute spur gears. In general, gear life predictions based on dynamic loads differed significantly from those based on static loads, with the predictions being strongly influenced by the maximum dynamic load during contact. Gear mesh operating speed strongly affected predicted dynamic load and life. Meshes operating at a resonant speed or one-half the resonant speed had significantly shorter lives. Dynamic life factors for gear surface pitting fatigue were developed on the basis of the parametric studies. In general, meshes with higher contact ratios had higher dynamic life factors than meshes with lower contact ratios. A design chart was developed for hand calculations of dynamic life factors. (Author).
Download or read book An Investigation of the Dynamic Loads in Spur gear Teeth written by and published by . This book was released on 1962 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: By John Sinclaire Howland.
Download or read book Analysis of the Influence of Errors and Stiffness on Dynamic Loads Developed in Spur and Helical Gears written by Donald Russell Houser and published by . This book was released on 1969 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Minimizing the Dynamic Load of High Contact Ratio Spur Gear Using Profile Modification written by Srijana Shah and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the major concern in the design of power transmission gear is the reduction of gear dynamic load. Research on gear noise and vibration has revealed that the basic mechanics of noise generated from gearing is gear box vibration excited by the dynamic load. This thesis studies the effect of tooth spacing errors on the dynamic load of high contact ratio spur gear subjected to unideal loading conditions. Spur gear is the simplest kind gear available. Spur gears have their teeth parallel to the axis of rotation and are used for transmitting power between two parallel shafts. Three types of spacing error distribution are defined and studied: type I (short span), type II (medium span), and type III (long span). Three different kinds of modification have been considered: linear, parabolic 1, parabolic II. The range of loading is changed from 0.75 times to 1.25 times of design load which is 2200 lb.-inch. A computer simulation has been conducted to investigate the effectiveness of profile modification for reducing dynamic loads in high-contact-ratio gears with different tooth spacing errors. The simulation examined varying amplitudes of spacing errors and differences in the span of teeth over which the errors occur. The dynamic analysis was performed using a revised version of a NASA gear dynamics code, modified to take into consideration the tooth spacing errors in the dynamic analysis. The findings of this study can be used to design robust tooth profile modification for improving the dynamic performance of high-contact-ratio gear sets with different tooth spacing errors when subjected to unideal loading condition.
Download or read book A Study of Deflection of Gear Teeth Under Dynamic Loads written by Dan James Mihalopoulos and published by . This book was released on 1941 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Dynamic Loads on Spur Gear Teeth written by Sumant A. Patel and published by . This book was released on 1969 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ASME 71 DE 26 written by Romualdas Kasuba and published by . This book was released on 1971 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An investigation of the dynamic response of spur gear teeth with moving loads written by C. E. Passerello and published by . This book was released on 1987 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two concepts relating to gear dynamics were studied. The first phase involved the analysis of the effect of the speed of a moving load on the dynamic deflections of a gear tooth. A single spur gear tooth modelled using finite elements was subjected to moving loads with variable velocities. The tooth tip deflection time histories were plotted, from which it was seen that the tooth tip deflection consisted of a quasistatic response with an oscillatory response superimposed on it whose amplitude was dependent on the type of load engagement. Including the rim in the analysis added flexibility to the model but did not change the general behaviour of the system. The second phase involved an investigation to determine the effect on the dynamic response of the inertia of the gear tooth. A simplified analysis using meshing cantilever beams was used. In one case, the beams were assumed massless, in the other, the mass (inertia) of the beams are included. From this analysis it was found that the inertia of the tooth did not affect the dynamic response of meshing cantilever beams. Keyword: Gear noise; Vibration; Machine design; Finite element analysis.
Download or read book An Investigation of the Dynamic Response of Spur Gear Teeth with Moving Loads written by Lyle W. Shuey and published by . This book was released on 1983 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Abstracts of Dissertations Theses and Research Papers Submitted by Candidates for Degrees written by Naval Postgraduate School (U.S.) and published by . This book was released on 1966 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Investigation of the Dynamic Response of Spur Gear Teeth with Moving Loads written by and published by . This book was released on 19?? with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Balancing Dynamic Strength of Spur Gears Operated at Extended Center Distance written by and published by . This book was released on 1996 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Compilation of Abstracts of Dissertations Theses and Research Papers Submitted by Candidates for Degrees written by Naval Postgraduate School (U.S.) and published by . This book was released on 1967 with total page 792 pages. Available in PDF, EPUB and Kindle. Book excerpt:
