Download or read book A Study Into Methods of Cleaning and Sanitizing Ultrafiltration Membranes written by Anne Ying-chen Lee and published by . This book was released on 1975 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cleaning and Sanitizing of Ultrafiltration Membranes written by Hans F. Bohner and published by . This book was released on 1991 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cleaning and Pre treatment Techniques for Ultrafiltration Membranes Fouled by Pulp and Paper Effluent written by P. Swart and published by . This book was released on 2003 with total page 67 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oil Removal for Produced Water Treatment and Micellar Cleaning of Ultrafiltration Membranes written by Scott Jay Beech and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Produced water is a major waste produced from oil and natural gas wells in the state of Texas. This water could be a possible source of new fresh water to meet the growing demands of the state after treatment and purification. This thesis describes a research project that evaluated the treatment of brine generated in oil fields (produced water) with ultrafiltration membranes. The characteristics of various ultrafiltration membranes for oil and suspended solids removal from produced water were studied to test whether they could be used in a pretreatment method. The research measured the effect of pressure and flow rate on performance of three commercially available membranes for treatment of oily produced water. Oil and suspended solids removal were measured by using turbidity and oil in water measurements taken periodically. The study also analyzed the flux through the membrane and any effect it had on membrane performance. The research showed that an ultrafiltration membrane provided turbidity removal of over 99% and oil removal of 78% for the produced water samples. The results indicated that the ultrafiltration membranes would be useful as one of the first steps in purifying the water. Membrane cleaning of produced water-fouled membranes by micellar solutions was investigated. A neutral pH and ambient temperature micelle solution for effective cleaning of oily water-fouled membranes was developed and studied. The performance of cleaning solutions on ultrafiltration membranes was investigated on laboratory size membrane testing equipment. Different micro emulsion solutions were studied to evaluate the effect of solution properties on cleaning performance. Three types of multiple membranes were studied, each having the same polyvinylidene fluoride (PVDF) material but with different nominal separation or flux characteristics. The data showed that the use of a micelle solution to clean the produced water-fouled membranes was a feasible and effective method. The study showed with further adjustment of the micelle solution the cleaning effectiveness could be optimized to provide double the effectiveness of current industry methods for membranes fouled by produced water.
Download or read book Ultrafiltration Membrane Cleaning Processes written by Guillem Gilabert-Oriol and published by Walter de Gruyter GmbH & Co KG. This book was released on 2021-06-08 with total page 141 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the ultrafiltration membranes, specifically focusing on the elements that are produced using PVDF technology and out-side-in configuration. It specifically targets ultrafiltration technology as a pretreatment of seawater reverse osmosis desalination process. However, what is described in the book can be leveraged in other ultrafiltration membrane types. It explains how to significantly improve the efficiency of the process.
Download or read book Cleaning and Sanitizing of Spiral wound Polysulfone Ultrafiltration Membranes written by Karen Elaine Smith and published by . This book was released on 1990 with total page 520 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Surface Modifying Macromolecules SMM Incorporated Ultrafiltration Membranes for Natural Organic Matter NOM Removal written by Thanh Huyen Dang and published by . This book was released on 2009 with total page 638 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Chemical Cleaning of Potable Microfiltration and Ultrafiltration Membranes written by Nicandro Porcelli and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Concerns over possible waterborne disease forced drinking water supply companies in England and Wales to adopt microfiltration and ultrafiltration technologies rapidly. MF and UF membrane plants are designed to produce water of a consistent quality regardless of throughput and fluctuations in the feedwater quality. To operate well they need to maintain flux and balance the rate of fouling, and chemical cleaning performance is critical to this. Giant steps have been taken into characterizing the foulants scientifically in the last few years while cleaning is reactive and ad hoc. This thesis explores the basis for a corresponding cleaning science for the technology to develop quantitively. Cleaning performance was defined in terms of a response to combinations of explanatory variables in a materials limited cleaning envelope. The study focused on applying variations of cleanant concentration, applied temperature and soak times to a variety of membranes fouled with different waters and regimes. An experimental design was developed and applied consistently to a number of different sampled sites; allowing an optimised recovery from the polynomial expressions for each treatment, through factorial analysis of the data. The size and variety of the data set analysed allowed comparison and quantification of the different deviations from optimal cleaning response. This effect was seen to vary temporally and with operating regime and the methods usefulness as a practical tool in the membrane plant lifecycle was considered. Cost evaluation of the variation in cleaning response showed that sub-optimal cleaning costs and energy use may be significant and the thesis also illustrated how module geometry affects initial cake deposition and thus cleanability. By demonstrating the potential for cleaning factor analysis, the potential for a combined heuristic and predictive cleaning control science is possible, but will need new strategies to manage technology change.
Download or read book Chemical Cleaning of Potable Microfiltration and Ultrafiltration Membranes written by and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Concerns over possible waterborne disease forced drinking water supply companies in England and Wales to adopt microfiltration and ultrafiltration technologies rapidly. MF and UF membrane plants are designed to produce water of a consistent quality regardless of throughput and fluctuations in the feedwater quality. To operate well they need to maintain flux and balance the rate of fouling, and chemical cleaning performance is critical to this. Giant steps have been taken into characterizing the foulants scientifically in the last few years while cleaning is reactive and ad hoc. This thesis explores the basis for a corresponding cleaning science for the technology to develop quantitively. Cleaning performance was defined in terms of a response to combinations of explanatory variables in a materials limited cleaning envelope. The study focused on applying variations of cleanant concentration, applied temperature and soak times to a variety of membranes fouled with different waters and regimes. An experimental design was developed and applied consistently to a number of different sampled sites; allowing an optimised recovery from the polynomial expressions for each treatment, through factorial analysis of the data. The size and variety of the data set analysed allowed comparison and quantification of the different deviations from optimal cleaning response. This effect was seen to vary temporally and with operating regime and the methods usefulness as a practical tool in the membrane plant lifecycle was considered. Cost evaluation of the variation in cleaning response showed that sub-optimal cleaning costs and energy use may be significant and the thesis also illustrated how module geometry affects initial cake deposition and thus cleanability. By demonstrating the potential for cleaning factor analysis, the potential for a combined heuristic and predictive cleaning control science is possible, but will need new strategies to manage technology change.
Download or read book Ultrafiltration Membranes and Applications written by Anthony R. Cooper and published by Springer Science & Business Media. This book was released on 2013-03-12 with total page 691 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a record of a symposium, "Ultrafiltration Membranes and Applications," which was held at the l78th National Meeting of the American Chemical Society in Washington, D.C., September 11-13, 1979. In organlzlng these sessions, I hoped to provide a comprehensive survey of the current state of ultrafiltration theory, the most recent advances in membrane technology, and a thorough treatment of existing applications and future directions for ultrafiltration. For me, the symposium was an outstanding success. It was a truly international forum with stimulating presentations and an enthusiastic audience. I hope that some of this spirit has spilled over into this volume, which is intended to reach a much wider audience. I am indebted to the Division of Colloid and Surface Chemistry of the American Chemical Society for their sponsorship. ANTHONY R. COOPER Palo Alto, California }larch, 1980 vii CONTENTS PART I. FUNDMfENTALS Fifteen Years of Ultrafiltration: Problems and Future Promises of an Adolescent Technology . . 1 Alan S. Michaels Production, Specification, and Some Transport Characteristics of Cellulose Acetate Ultrafil tration Membranes for Aqueous Feed Solutions 21 S. Sourirajan, Takeshi Matsuura Fu-Hung Hsieh and Gary R. Gildert Chemical and Morphological Effects of Solute Diffusion Through Block Copolymer Membranes 45 Yatin B. Thakore, Dien-Feng Shieh and Donald J. Lyman Practical Aspects in the Development of a Polymer Matrix for Ultrafiltration. 57 Israel Cabasso Permeability Parameters of a Novel Polyamide Membrane. ... - ...
Download or read book Screening of Microfiltration and Ultrafiltration Ceramic Membranes for Produced Water Treatment and Testing of Different Cleaning Methods written by Ali Heydari Beni and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Development and Implementation of Biological Cleaning Techniques for Ultrafiltration and Reverse Osmosis Membranes Fouled by Organic Substances written by Pieter Swart and published by . This book was released on 1998 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Combining Polymers with Chemical Thermal and Turbulent Conditions to Clean an Ultrafiltration Membrane written by Wen-Ching Tzeng and published by . This book was released on 1990 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Study of Fouling on Ceramic Ultrafiltration Membranes by Model Solutions and Natural Waters written by Leila Munla and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the last decade polymeric membranes have emerged as an economically viable treatment option to produce drinking water. Due to higher capital costs, the use of ceramic membranes has generally been limited to industrial applications that deal with challenging water quality. Ceramic membranes are superior to polymeric membranes in their physical and chemical resistance, which allows for higher fluxes and backwash pressures as well as rigorous chemical cleaning. As a result, these membranes can potentially operate for longer periods of time, which can decrease the lifetime cost of the membrane. Furthermore, decreased production costs coupled with an increased desire for economical sustainability may open the door for the use of ceramic membranes in drinking water treatment, particularly for highly polluted waters. The loss of membrane permeability as a result of fouling remains one of the biggest challenges for sustainable membrane operation. Therefore, a thorough understanding of fouling behavior and the identification of key foulants is essential for optimizing membrane performance. However, fouling has not been researched in detail for ceramic membranes in drinking water treatment, particularly ultrafiltration, since most research has focused on ceramic microfiltration membranes combined with coagulation. The thesis is divided into four main stages. The first stage involved developing a factorial design to establish a procedure to determine sustainable flux that can adequately compare the fouling between a ceramic and polymeric membrane without compromising the functional potential or operating parameters of either membrane. In this stage, the significance of three different variables (interval length, increment increase, and a hydraulic backwash) in determining sustainable flux were statistically analyzed following a factorial design and consequently included or removed from the sustainable flux determination approach. The increment increase was not significant while the backwash was the most significant variable. The method established was used in later experiments to allow for a comparison of fouling behavior and performance between a polymeric and ceramic membrane. The second stage investigated the fouling behavior of flat-sheet ceramic membranes with model solutions at constant pressure to identify foulants of concern and likely fouling mechanisms for ceramic membranes as well as perform surface characterization techniques not possible with tubular membranes. In this stage the contributions of different model foulants (bovine serum albumin i.e. a protein, alginate i.e. a carbohydrate, humic acid, and colloidal silica) to reversible and irreversible fouling on a flat-sheet ceramic membrane at constant pressure were quantitatively evaluated. Both single foulant solutions and all possible combinations of mixtures of model foulants were investigated. The bovine serum albumin and humic acid were main contributors to hydraulically irreversible fouling and their removal mechanism is postulated to be largely through adsorption. Colloidal silica was the most influential factor governing fouling behavior and diminished the irreversible fouling effect of these organics, thus increasing hydraulic reversibility. Additionally, synergistic fouling effects were also observed. The third stage investigated the same model solutions with tubular ceramic membranes at constant flux to determine the fouling behavior under different conditions and quantitatively assess the effectiveness of different fouling mitigation techniques. The rate of fouling was very high for bovine serum albumin but extremely low for humic acid; however, they both showed high irreversible fouling. The results obtained were consistent with the previous stage using flat-sheet ceramic membranes; particularly regarding the significant role colloidal silica plays in fouling. The ability to compare these two very different configurations and operating parameters is largely due to the use of a hydraulic backwash in both configurations. Therefore, this highlights the importance of investigating fouling reversibility, especially in simplified experiments. The last stage investigated tubular ceramic fouling behavior and organic matter rejection with surface water at constant flux. Tubular ceramic membrane fouling behavior was investigated for river water. A very high initial organic carbon removal was observed at the initial stages of filtration and after each backwash cycle indicating a high affinity of organics to the membrane surface as well as partially reversible adsorption. Humic acid rejection decreased throughout the filtration cycle. On the contrary, biopolymer rejection remained constant indicating size exclusion as a primary removal mechanism. After several modifications to the design and setup, the sustainable flux method established in Stage 1 could not be applied to the ceramic membrane or to the polymeric membrane using highly turbid water; a few hypotheses were made as to why this occurred. It is likely that one or more variables that were not included in the sustainable flux method were influencing the fouling rate over time. Overall, the robustness of ceramic membranes opens the door for some creative fouling mitigation techniques to be used such as backwash pulses and chemical maintenance cleaning.
Download or read book Biopharmaceutical Manufacturing written by Gary Gilleskie and published by Walter de Gruyter GmbH & Co KG. This book was released on 2021-09-07 with total page 347 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biopharmaceuticals, medicines made by or from living organisms (including cells from living organisms), are extremely effective in treating a broad range of diseases. Their importance to human health has grown significantly over the years as more biopharmaceutical products have entered the market, and now the biggest selling drugs in the world are biopharmaceuticals. Biopharmaceutical Manufacturing: Principles, Processes and Practices provides concise, comprehensive, and up-to-date coverage of biopharmaceutical manufacturing. Written in a clear and informal style, the content has been influenced by the authors’ substantial industry experience and teaching expertise. That expertise enables the authors to address the many questions posed over the years both by university students and professionals with experience in the field. Consequently, the book will appeal both to undergraduate or graduate students using it as a textbook and specialized industry practitioners seeking to understand the big picture of biopharmaceutical manufacturing. This book:
Download or read book Synthetic Membranes written by P.M. Bungay and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 735 pages. Available in PDF, EPUB and Kindle. Book excerpt: The chapters in this book are based upon lectures given at the NATO Advanced Study Institute on Synthetic Membranes (June 26-July 8, 1983, Alcabideche, Portugal), which provided an integrated presentation of syn thetic membrane science and technology in three broad areas. Currently available membrane formation mechanisms are reviewed, as well as the manner in which synthesis conditions can be controlled to achieve desired membrane structures. Membrane performance in a specific separa tionprocess involves complex phenomena, the understanding of which re quires a multidisciplinary approach encompassing polymer chemistry, phys ical chemistry, and chemical engineering. Progress toward a global understanding of membrane phenomena is described in chapters on the principles of membrane transport. The chapters on membrane processes and applications highlight both established and emerging membrane processes, and elucidate their myriad applications. It is our hope that this book will be an enduring, comprehensive compen dium of the state of knowledge in the field of synthetic membranes. We have been encouraged in that hope by numerous expressions of interest in the book, coming from a variety of potential users.
Download or read book Proceedings written by and published by . This book was released on 1973 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:
