Download or read book Wideband GaN Microwave Power Amplifiers with Class G Supply Modulation Band 48 written by Nikolai Wolff and published by FBI / Ferdinand Braun Institut. This book was released on 2019 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The continuous and rapidly growing demand for mobile communication access led to a major increase in the number of base stations worldwide to provide sufficient coverage and quality of service. As a consequence, mobile communication networks have become a significant contributor to global energy consumption. Several advanced topologies for efficiency improvement of RF power amplifiers have been developed. Modulating the amplifier's supply voltage according to the variation of the envelope signal is one of the most promising concepts. This topology is investigated here, with an architecture that switches the supply voltage of the power amplifier in discrete levels with a class-G supply modulator. The thesis addresses comprehensively all aspects of class-G supply modulation. Several prototype designs were realized to validate the theory and to gain experience on the influence of the corresponding parameters. These include the discrete supply voltage levels, the switching thresholds, and the interface between the RF PA and the class-G supply modulator. Efforts both on improving the RF power amplifiers and developing several class-G supply modulators were also involved. This work covers the progress up to a PA module that provides an instantaneous modulation bandwidth of 120 MHz and achieves better performance than state-of-the art continuous supply modulation systems. Class-G supply modulated RF power amplifiers based on gallium nitride technology exhibit a strong nonlinear behavior, therefore linearization is required. For this purpose, the linearization with digital predistortion based on behavioral models is optimized for the class-G topology and a novel predistorter model is developed and analyzed.

Download or read book A deep ultraviolet laser light source by frequency doubling of GaN based external cavity diode laser radiation written by Norman Ruhnke and published by Cuvillier Verlag. This book was released on 2022-05-13 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compact and portable laser light source emitting in the wavelength range between 210 nm and 230 nm would enable numerous applications outside of laboratory environments, such as sterilization and disinfection of medical equipment, water purification or gas and air analysis using absorption spectroscopy. Such a source is also highly attractive for the identification and quantification of proteins and biomolecules by means of laser-induced fluorescence or Raman spectroscopy. In this thesis, a novel concept to realize such a compact and portable laser light source with low power consumption and an emission around 222 nm is investigated. The developed concept is based on single-pass frequency doubling of a commercially available high-power GaN laser diode emitting in the blue spectral range. Due to the low frequency doubling conversion efficiencies in this wavelength range of about 10-4 W-1, a laser diode with high optical output power above 1 W is required as pump source. Moreover, it has to exhibit narrowband emission in the range of the acceptance bandwidth of the applied nonlinear BBO crystal. Since GaN-based high-power laser diodes typically show broad emission spectra of Δλ = 1…2 nm, stabilizing and narrowing their wavelength by using external wavelength-selective elements is investigated and presented for the first time. With the understanding for the novel concept gained in this work, a compact ultraviolet laser light source was realized. It has a power consumption of less than 10 W and is exceptionally robust due to its immoveable components. The demonstrated output power of 160 μW enables numerous industrial and everyday applications for which previous laser systems have been too complex and overly cost- and energy-intensive.

Download or read book Design simulation and analysis of laterally longitudinally non uniform edge emitting GaAs based diode lasers Band 73 written by Jan-Philipp Koester and published by Cuvillier Verlag. This book was released on 2023-09-19 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Edge-emitting quantum-well diode lasers based on GaAs combine a high conversion efficiency, a wide range of emission wavelengths covering a span from 630 nm to 1180 nm, and the ability to achieve high output powers. The often used longitudinal-invariant Fabry-Pérot-type resonators are easy to design but often lead to functionality or performance limitations. In this work, the application of laterally-longitudinally non-uniform resonator configurations is explored as a way to reduce unwanted and performance-limiting effects. The investigations are carried out on existing and entirely newly developed laser designs using dedicated simulation tools. These include a sophisticated time-dependent laser simulator based on a traveling-wave model of the optical fields in the lateral-longitudinal plane and a Maxwell solver based on the eigenmode expansion method for the simulation of passive waveguides. Whenever possible, the simulation results are compared with experimental data. Based on this approach, three fundamentally different laser types are investigated: • Dual-wavelength lasers emitting two slightly detuned wavelengths around 784 nm out of a single aperture • Ridge-waveguide lasers with tapered waveguide and contact layouts that emit light of a wavelength of around 970 nm • Broad-area lasers with slightly tapered contact layouts emitting at 910 nm The results of this thesis underline the potential of lateral-longitudinal non-uniform laser designs to increase selected aspects of device performance, including beam quality, spectral stability, and output power.

Download or read book Transceiver Technologies for Millimeter Wave Beam Steering Applications Band 71 written by Yi-Fan Tsao and published by Cuvillier Verlag. This book was released on 2022-11-08 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: During the past years, wireless communication systems have been rapidly advancing to meet the high data-rate requirements of various emerging applications. However, the existing transceivers have typically been demonstrated using CMOS-compatible technologies that deliver a relatively low equivalent isotropic radiated power in a small unit cell. Moreover, the particular device characteristics are limiting the linear region for operation. Therefore, the main focus of this dissertation is to present and discuss new design methods for transceivers to solve these issues. To reduce the complexity of the transceiver module for further phased-array scaling, a low-noise power amplifier design approach is designed using a 0.15-μm GaN-on-SiC high-electron mobility transistor technology (HEMT). Utilizing a traded off interstage matching topology between loss and bandwidth, the conversion loss induced by the matching network could be effectively reduced. A stacked-FET configuration was adopted to enhance the power handling of the RF switch. Further improvement on the isolation bandwidth was investigated using theoretical analysis on the intrinsic effect of the passive HEMTs. With the successful implementation of the RF front-end circuits, transceiver modules were integrated on Rogers RO3010 substrate. The planar dual exponentially tapered slot antenna phased-array system showed a compact size with simple biasing network compared to the conventional transceiver approach. The presented T/R module was characterized with an over-the-air test at a distance of 1 m, overcoming the free space path loss of 64 dB. It also shows a high flexibility for further integration with a larger number of array systems, which is very promising for future 5G communication systems.

Download or read book Two step MOVPE in situ etching and buried implantation applications to the realization of GaAs laser diodes written by Pietro della Casa and published by Cuvillier Verlag. This book was released on 2021-03-25 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work is about two-step epitaxial growth using metalorganic vapor-phase epitaxy (MOVPE) for the realization of edge-emitting near-infrared laser diodes. The fabricated gallium arsenide-based devices fall into two categories: high-power lasers (watt range, multimodal) and tunable lasers (milliwatt range, monomodal). Common to both cases is that surface contamination – particularly that due to oxygen – needs to be removed before regrowth. Thus, in-situ etching with carbon tetrabromide (CBr4) is first studied. The experimental results include kinetic data, the effects of different etching conditions as well as substrate characteristics, and the effectiveness in reducing surface contamination. These investigations pave the way to devices based on 2-step epitaxy combined with in-situ etching. Correspondingly, thermally-tuned SG-DBR lasers operating around 975 nm have been successfully realized, obtaining a tuning range of 21 nm. In addition, the possibility of using electronic tuning in similar devices has been explored. High-power broad-area lasers have also been realized, using two-step epitaxy combined with ex-situ and in-situ etching, to create a buried, shallow “mesa” containing the active zone. This approach allows introducing lateral electrical and optical confinement, and – simultaneously – non-absorbing mirrors at the laser facets. Additionally, a different strategy to create a buried current aperture is presented, which is based on ion implantation followed by epitaxial regrowth. This enables to improve device performance and simultaneously introduce non-absorbing mirrors at the facets with correspondingly increased reliability.

Download or read book Analysis of Spatio Temporal Phenomena in High Brightness Diode Lasers using Numerical Simulations written by Anissa Zeghuzi and published by Cuvillier Verlag. This book was released on 2020-10-22 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: Broad-area lasers are edge-emitting semiconductor lasers with a wide lateral emission aperture. This feature enables high output powers but also diminishes the lateral beam quality and results in their inherently non-stationary behavior. Research in the area is driven by application, and the main objective is to increase the brightness, which includes both output power and lateral beam quality. To understand the underlying spatio-temporal phenomena and to apply this knowledge in order to reduce costs for brightness optimization, a self-consistent simulation tool taking all essential processes into account is vital. Firstly, in this work a quasi-three-dimensional opto-electronic and thermal model is presented that describes essential qualitative characteristics of real devices well. Time-dependent traveling-wave equations are utilized to characterize the inherently non-stationary optical fields, which are coupled to dynamic rate equations for the excess carriers in the active region. This model is extended by an injection-current-density model to accurately include lateral current spreading and spatial hole burning. Furthermore, a temperature model is presented that includes short-time local heating near the active region as well as the formation of a stationary temperature profile. Secondly, the reasons of brightness degradation, i.e. the origins of power saturation and the spatially modulated field profile, are investigated. And lastly, designs that mitigate those effects limiting the lateral brightness under pulsed and continuous-wave operation are discussed. Amongst those designs a novel “chessboard laser” is presented that utilizes longitudinal-lateral gain-loss modulation and an additional phase tailoring to obtain a very low far-field divergence.

Download or read book Spectroscopic Applications of Terahertz Quantum Cascade Lasers written by Tasmim Alam and published by Cuvillier Verlag. This book was released on 2020-10-29 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quantum cascade lasers (QCLs) are attractive for high-resolution spectroscopy because they can provide high power and a narrow linewidth. They are particularly promising in the terahertz (THz) range since they can be used as local oscillators for heterodyne detection as well as transmitters for direct detection. However, THz QCL-based technologies are still under development and are limited by the lack of frequency tunability as well as the frequency and output power stability for free-running operation. In this dissertation, frequency tuning and linewidth of THz QCLs are studied in detail by using rotational spectroscopic features of molecular species. In molecular spectroscopy, the Doppler eff ect broadens the spectral lines of molecules in the gas phase at thermal equilibrium. Saturated absorption spectroscopy has been performed that allows for sub-Doppler resolution of the spectral features. One possible application is QCL frequency stabilization based on the Lamb dip. Since the tunability of the emission frequency is an essential requirement to use THz QCL for high-resolution spectroscopy, a new method has been developed that relies on near-infrared (NIR) optical excitation of the QCL rear-facet. A wide tuning range has been achieved by using this approach. The scheme is straightforward to implement, and the approach can be readily applied to a large class of THz QCLs. The frequency and output stability of the local oscillator has a direct impact on the performance and consistency of the heterodyne spectroscopy. A technique has been developed for a simultaneous stabilization of the frequency and output power by taking advantage of the frequency and power regulation by NIR excitation. The results presented in this thesis will enable the routine use of THz QCLs for spectroscopic applications in the near future.

Download or read book AlN base layers for UV LEDs written by Sebastian Walde and published by Cuvillier Verlag. This book was released on 2021-06-22 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: To enable the fabrication of high performance ultraviolet (UV) light-emitting diodes (LEDs) this work aims at improving the quality of AlN base layers on sapphire substrates. The main issues for UV LEDs are still a limited internal quantum efficiency due to a high amount of threading dislocations along with a limited light extraction efficiency due to total internal reflection at the AlN/sapphire interface. Therefore, high-temperature annealing of AlN/sapphire layers and growth on nanopatterned sapphire substrates were comprehensively investigated. High-temperature annealing was applied to AlN layers of different strain and thickness grown by metalorganic vapour phase epitaxy (MOVPE). The threading dislocation density could be successfully reduced by more than one order of magnitude down to 6 × 108 cm-2. Wave optical simulations of UV LEDs on nanopatterned sapphire substrates (NPSS) were conducted and showed a potential increase in light extraction efficiency compared to a planar substrate. The optimized MOVPE growth process on sapphire nanopillars and sapphire nanoholes resulted in a fully coalesced and atomically smooth AlN surface. The threading dislocation density was reduced to 1 ×109 cm-2 for AlN on both nanopillars and nanoholes. UVC LEDs emitting at 265 nm wavelength were grown on top of the developed templates. Increased internal efficiency was obtained by reduced dislocation density and more efficient light extraction was achieved on NPSS in case of a transparent heterostructure and reflective contacts. Thus, the developed templates yield considerable improvement in light output compared to conventional templates.

Download or read book Broad Area Laser Bars for 1 kW Emission written by Matthias M. Karow and published by Cuvillier Verlag. This book was released on 2022-06-27 with total page 143 pages. Available in PDF, EPUB and Kindle. Book excerpt: ndustrial laser systems for material processing applications rely on the availability of highly efficient, high-brightness diode lasers. GaAs-based broad-area laser bars play a vital role in such applications as pump sources for high-beam-quality solid-state lasers and, increasingly, as direct processing tools. This work studies 940 nm-laser bars emitting 1 kW optical power at room temperature, identifying those physical mechanisms that are currently limiting electrical-to-optical conversion efficiency as well as lateral beam quality. In the process, several diagnostic studies on bars with varied lateral-longitudinal design were carried out. The effects of technological measures for performance optimization were analyzed, yielding a new benchmark in efficiency and lateral divergence. The studies into altered resonator lengths of 4 and 6 mm as well as fill factors between 69 and 87 % successfully reduce both the voltage dropping across the device and power saturation at high currents, enabling 66 % efficiency at the operation point. Concrete measures how to reach efficiencies ≥70 % are presented thereafter, showing that doubling the efficiency value of the first 1 kW-demonstration in 2007 – amounting to 35 % – is in near reach. Investigation of the beam quality bases on a herein proposed and realized concept, in which the far field is resolved for each individual bar emitter. In this way, it is possible to determine how far-field profiles vary along the bar width and how much these variations affect the overall bar far-field. Further, such effects specific to bar structures can be separated into non-thermal and thermal influences. The effect of mechanical chip deformation (bar smile) as well as neighboring-emitter interaction has been investigated for the first time in active kW-class devices, yielding a lateral divergence as low as 8.8° at the operation point.

Download or read book Distributed Power Amplifiers for RF and Microwave Communications written by Narendra Kumar and published by Artech House. This book was released on 2015-06-01 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new resource presents readers with all relevant information and comprehensive design methodology of wideband amplifiers. This book specifically focuses on distributed amplifiers and their main components, and presents numerous RF and microwave applications including well-known historical and recent architectures, theoretical approaches, circuit simulation, and practical implementation techniques. A great resource for practicing designers and engineers, this book contains numerous well-known and novel practical circuits, architectures, and theoretical approaches with detailed description of their operational principles.

Download or read book Recent Technical Developments in Energy Efficient 5G Mobile Cells written by Raed A. Abd-Alhameed and published by MDPI. This book was released on 2020-06-17 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses the true innovation in engineering design that may be promoted by blending together models and methodologies from different disciplines, and, in this book, the target was exactly to follow this approach to deliver a new disruptive architecture to deliver these next-generation mobile small cell technologies. According to this design philosophy, the work within this book resides in the intersection of engineering paradigms that includes “cooperation”, “network coding”, and “smart energy-aware frontends”. These technologies will not only be considered as individual building blocks, but re-engineered according to an inter-design approach resulting in the enabler for energy efficient femtocell-like services on the move. The book aims to narrow the gap between the current networking technologies and the foreseen requirements that are targeted at the future development of the 5G mobile and wireless communications networks in terms of the higher networking capacity, the ability to support more users, the lower cost per bit, the enhanced energy efficiency, and adaptability to new services and devices (for example, smart cities, and the Internet of things (IoT)).

Download or read book RF and Microwave Power Amplifier Design written by Andrei Grebennikov and published by McGraw Hill Professional. This book was released on 2004-09-15 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a rigorous tutorial on radio frequency and microwave power amplifier design, teaching the circuit design techniques that form the microelectronic backbones of modern wireless communications systems. Suitable for self-study, corporate training, or Senior/Graduate classroom use, the book combines analytical calculations and computer-aided design techniques to arm electronic engineers with every possible method to improve their designs and shorten their design time cycles.

Download or read book Microwave Electronics written by Giovanni Ghione and published by Cambridge University Press. This book was released on 2018 with total page 599 pages. Available in PDF, EPUB and Kindle. Book excerpt: A self-contained guide to microwave electronics, covering passive and active components, linear, low-noise and power amplifiers, microwave measurements, and CAD techniques. It is the ideal text for graduate and senior undergraduate students taking courses in microwave and radio-frequency electronics, as well as professional microwave engineers.

Download or read book Wideband GaN Microwave Power Amplifiers with Class G Supply Modulation written by Nikolai Wolff and published by Cuvillier Verlag. This book was released on 2019-02-06 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: The continuous and rapidly growing demand for mobile communication access led to a major increase in the number of base stations worldwide to provide sufficient coverage and quality of service. As a consequence, mobile communication networks have become a significant contributor to global energy consumption. Several advanced topologies for efficiency improvement of RF power amplifiers have been developed. Modulating the amplifier’s supply voltage according to the variation of the envelope signal is one of the most promising concepts. This topology is investigated here, with an architecture that switches the supply voltage of the power amplifier in discrete levels with a class-G supply modulator. The thesis addresses comprehensively all aspects of class-G supply modulation. Several prototype designs were realized to validate the theory and to gain experience on the influence of the corresponding parameters. These include the discrete supply voltage levels, the switching thresholds, and the interface between the RF PA and the class-G supply modulator. Efforts both on improving the RF power amplifiers and developing several class-G supply modulators were also involved. This work covers the progress up to a PA module that provides an instantaneous modulation bandwidth of 120 MHz and achieves better performance than state-of-the art continuous supply modulation systems. Class-G supply modulated RF power amplifiers based on gallium nitride technology exhibit a strong nonlinear behavior, therefore linearization is required. For this purpose, the linearization with digital predistortion based on behavioral models is optimized for the class-G topology and a novel predistorter model is developed and analyzed.

Download or read book Dynamic Power Supply Transmitters written by Earl McCune and published by Cambridge University Press. This book was released on 2015-05-21 with total page 495 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Power is dissipated (lost) when this current flows through any resistance, which includes the amplifier's transistor. This dissipated power is the product of the current in the load times the voltage difference between the supply voltage to the amplifier and the output signal voltage. When the voltage supplied to the amplifier is a constant value, and by far the most common design practice, the situation in Fig. 1-2a results. Power dissipation in the amplifier is maximum when the output signal voltage is 1/2 of the supply voltage. When the output signal voltage is higher, even though the current value is larger the voltage drop is less and the power dissipation is lower. Similarly, when the output signal voltage is small, even though the voltage drop is now large the current in the load is smaller and again the power dissipation is lower"--

Download or read book Millimeter Wave Power Amplifiers written by Jaco du Preez and published by Springer. This book was released on 2017-10-05 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a detailed review of millimeter-wave power amplifiers, discussing design issues and performance limitations commonly encountered in light of the latest research. Power amplifiers, which are able to provide high levels of output power and linearity while being easily integrated with surrounding circuitry, are a crucial component in wireless microwave systems. The book is divided into three parts, the first of which introduces readers to mm-wave wireless systems and power amplifiers. In turn, the second focuses on design principles and EDA concepts, while the third discusses future trends in power amplifier research. The book provides essential information on mm-wave power amplifier theory, as well as the implementation options and technologies involved in their effective design, equipping researchers, circuit designers and practicing engineers to design, model, analyze, test and implement high-performance, spectrally clean and energy-efficient mm-wave systems.

Download or read book Fundamentals of RF and Microwave Transistor Amplifiers written by Inder Bahl and published by John Wiley & Sons. This book was released on 2009-06-17 with total page 696 pages. Available in PDF, EPUB and Kindle. Book excerpt: A Comprehensive and Up-to-Date Treatment of RF and Microwave Transistor Amplifiers This book provides state-of-the-art coverage of RF and microwave transistor amplifiers, including low-noise, narrowband, broadband, linear, high-power, high-efficiency, and high-voltage. Topics covered include modeling, analysis, design, packaging, and thermal and fabrication considerations. Through a unique integration of theory and practice, readers will learn to solve amplifier-related design problems ranging from matching networks to biasing and stability. More than 240 problems are included to help readers test their basic amplifier and circuit design skills-and more than half of the problems feature fully worked-out solutions. With an emphasis on theory, design, and everyday applications, this book is geared toward students, teachers, scientists, and practicing engineers who are interested in broadening their knowledge of RF and microwave transistor amplifier circuit design.