Download or read book Unshrouded Turbine Blade Tip Heat Transfer and Film Cooling written by Brian M. T. Tang and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Blade Tip and Near Tip Heat Transfer with Film Cooling written by Gregory Kramer and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Blade Film Cooling and Blade Tip Heat Transfer written by Shuye Teng and published by . This book was released on 2000 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Measurement and Analysis of Gas Turbine Blade Tip Heat Transfer and Film Cooling written by Jae Su Kwak and published by . This book was released on 2002 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Survey of Advantages and Problems Associated with Transpiration Cooling and Film Cooling of Gas turbine Blades written by Ernst Rudolf Georg Eckert and published by . This book was released on 1951 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summary: Transpiration and film cooling promise to be effective methods of cooling gas-turbine blades; consequently, analytical and experimental investigations are being conducted to obtain a better understanding of these processes. This report serves as an introduction to these cooling methods, explains the physical processes, and surveys the information available for predicting blade temperatures and heat-transfer rates. In addition, the difficulties encountered in obtaining a uniform blade temperature are discussed, and the possibilities of correcting these difficulties are indicated. Air is the only coolant considered in the application of these cooling methods.

Download or read book A Numerical Analysis of Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models written by Ali A. Ameri and published by . This book was released on 1999 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.

Download or read book Effects of Film Cooling on Turbine Blade Tip Flow Structures and Thermal Loading written by Louis Edward Christensen and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbine engines are an essential technology in aviation and power generation. One of the challenges associated with increasing the efficiency of gas turbines is the thermal loading experienced by the engine components downstream of the combustors especially the high-pressure turbine blades. High temperatures and rotational velocities can cause blade failures in numerous ways such as creep or stress rupture. Technologies like film cooling are implemented in these components to lower the thermal loading and reduce the risk of failure. However, these introduce complexities into the flow which in turn increases the difficulty of predicting the performance of film cooled turbines. Accurately predicting the capabilities of these components is essential to prevent failure in gas turbine engines. Engineers use a combination of experiments and computational simulations to understand how these technologies perform and predict the operating conditions and lifespan of these components. A combined experimental and numerical program is performed on a single stage high-pressure turbine to increase understanding of film cooling in gas turbines and improve computational methods used to predict their performance. The turbine studied is a contemporary production model from Honeywell Aerospace with both cooled and uncooled turbine blades. The experimental work is performed at The Ohio State University Gas Turbine Laboratory Turbine Test Facility, a short duration facility operating at engine corrected conditions. The experiments capture heat flux, temperature, and pressure data across the entire blade, but this work will focus on the turbine blade tip data. Tip temperature data are captured using a high-speed infrared camera providing a unique data set unseen in the current literature. In addition to the experiments, transient conjugate heat transfer simulations of a single turbine passage are performed to recreate the experiments and give insight into the flow field in the tip region of the turbine blades. The experiments and simulations are conducted to provide a better understanding of the interactions of the film cooling and tip flows along with their relationship to the thermal loading on the turbine blade tip. Film cooling in the tip region adds complexity to the flow and a non-intuitive relationship exists between film cooling and thermal loading. Addition of cooling is not guaranteed to reduce the thermal loading on the blade tips. Cooling jets can displace hot gases protecting the blade, but they are also capable of shifting flow structures and trapping hot gases near the blade surface especially so in corners of the blade tips. These direct and indirect methods of altering the thermal loading open a new path to optimization where engineers consider how the coolant alters the flow in addition to forming a protective layer of cool gas. This can be done to more effectively use coolant not only in the blade tips but elsewhere on the turbine blades leading to higher engine efficiencies and more sustainable gas turbine engines.

Download or read book Turbine Blade Tip Film Cooling Measurements written by Dean Andrew Ward and published by . This book was released on 1992 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Effect of Inlet Geometry on the Turbine Blade Tip Region Heat Transfer Coefficient and Effectiveness written by and published by . This book was released on 2002 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental investigation of the local film cooling effectiveness and heat transfer coefficient downstream of a row of elongated holes in a simulated axial turbine blade tip is presented. Film cooling is needed to protect the turbine blade tip region from high heat transfer rates, especially when cooling by convection is insufficient to keep the temperature distribution of the blade within the limits required. Accurate heat transfer predictions in this region of the blade are particularly difficult given the dimensionality of the flow and the narrow passage typical of turbine blades. The effect of inlet geometry film cooling injection point and blowing ratio are examined for an injection on the blade tip itself close to the pressure surface corner. Additionally the corner radii between the pressure surface and the tip were varied. The experimental method uses the steady state liquid crystal technique. Film cooling injection provides the tip with a blanket of protection from the hot leakage flow. This extends far downstream of the holes at higher blowing ratios. Inlet curvature provides greater local film cooling effectiveness but it lacks streamwise film cooling coverage. It is important to have direct injection onto the separation bubble for greater lateral film cooling coverage.

Download or read book Investigations of Flow and Film Cooling on Turbine Blade Edge Regions written by Huitao Yang and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The inlet temperature of modern gas turbine engines has been increased to achieve higher thermal efficiency and increased output. The blade edge regions, including the blade tip, the leading edge, and the platform, are exposed to the most extreme heat loads, and therefore, must be adequately cooled to maintain safety. For the blade tip, there is tip leakage flow due to the pressure gradient across the tip. This leakage flow not only reduces the blade aerodynamic performance, but also yields a high heat load due to the thin boundary layer and high speed. Various tip configurations, such as plane tip, double side squealer tip, and single suction side squealer tip, have been studied to find which one is the best configuration to reduce the tip leakage flow and the heat load. In addition to the flow and heat transfer on the blade tip, film cooling with various arrangements, including camber line, upstream, and two row configurations, have been studied. Besides these cases of low inlet/outlet pressure ratio, low temperature, non-rotating, the high inlet/outlet pressure ratio, high temperature, and rotating cases have been investigated, since they are closer to real turbine working conditions. The leading edge of the rotor blade experiences high heat transfer because of the stagnation flow. Film cooling on the rotor leading edge in a 11/2 turbine stage has been numerically studied for the designand off-design conditions. Simulations find that the increasing rotating speed shifts the stagnation line from the pressure side, to the leading edge and the suction side, while film cooling protection moves in the reverse direction with decreasing cooling effectiveness. Film cooling brings a high unsteady intensity of the heat transfer coefficient, especially on the suction side. The unsteady intensity of film cooling effectiveness is higher than that of the heat transfer coefficient. The film cooling on the rotor platform has gained significant attention due to the usage of low-aspect ratio and low-solidity turbine designs. Film cooling and its heat transfer are strongly influenced by the secondary flow of the end-wall and the stator-rotor interaction. Numerical predictions have been performed for the film cooling on the rotating platform of a whole turbine stage. The design conditions yield a high cooling effectiveness and decrease the cooling effectiveness unsteady intensity, while the high rpm condition dramatically reduces the film cooling effectiveness. High purge flow rates provide a better cooling protection. In addition, the impact of the turbine work process on film cooling effectiveness and heat transfer coefficient has been investigated. The overall cooling effectiveness shows a higher value than the adiabatic effectiveness does.

Download or read book Measurements of Local Heat Transfer Coefficient and Film Cooling Effectiveness in Turbine Blade Tip Geometries written by and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report results from a contract tasking Imperial College of Science. Technology and Medicine as follows: The project will involve the quantification of the flow and surface characteristics of turbine blade tip cooling geometry with velocity and turbulence distributions relevant to the gas turbine designer. The experimental program will provide measurements of the film cooling adiabatic effectiveness and heat transfer coefficient in a simulated blade tip. with injection from the pressure surface side near the tip. The program will be progressive and interactive. starting with a single row of film cooling holes with injection from the pressure surface side near the tip. moving towards other representative injection configurations: slot injection on the tip surface and groove-tip geometry. The project will supply validation data for the 3D Navier-Stokes solver Glenn-HT. currently used by NASA. and it will also provide insight into the performance of advanced cooling geometry configurations. The experiments will make use of liquid crystal thermography to obtain the heat transfer data. The data acquisition method corresponds to the steady-state technique with the use of wide band liquid crystals. It requires a reduced number of experiments when compared with narrow band crystals and thermocouples, and provides a high degree of spatial resolution and reduced uncertainty level. It will be accompanied by data from small-diameter thermocouples. hot wires and pressure transducers.

Download or read book A Numerical Analysis of Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-15 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computational study has been performed to predict the distribution of convective heat transfer coefficient on a simulated blade tip with cooling holes. The purpose of the examination was to assess the ability of a three-dimensional Reynolds-averaged Navier-Stokes solver to predict the rate of tip heat transfer and the distribution of cooling effectiveness. To this end, the simulation of tip clearance flow with blowing of Kim and Metzger was used. The agreement of the computed effectiveness with the data was quite good. The agreement with the heat transfer coefficient was not as good but improved away from the cooling holes. Numerical flow visualization showed that the uniformity of wetting of the surface by the film cooling jet is helped by the reverse flow due to edge separation of the main flow. Ameri, A. A. and Rigby, D. L. Glenn Research Center NASA/CR-1999-209165, NAS 1.26:209165, E-11756

Download or read book Experimental Study of Gas Turbine Blade Film Cooling and Heat Transfer written by Diganta P. Narzary and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern gas turbine engines require higher turbine-entry gas temperature to improve their thermal efficiency and thereby their performance. A major accompanying concern is the heat-up of the turbine components which are already subject to high thermal and mechanical stresses. This heat-up can be reduced by: (i) applying thermal barrier coating (TBC) on the surface, and (ii) providing coolant to the surface by injecting secondary air discharged from the compressor. However, as the bleeding off of compressor discharge air exacts a penalty on engine performance, the cooling functions must be accomplished with the smallest possible secondary air injection. This necessitates a detailed and systematic study of the various flow and geometrical parameters that may have a bearing on the cooling pattern. In the present study, experiments were performed in three regions of a non-rotating gas turbine blade cascade: blade platform, blade span, and blade tip. The blade platform and blade span studies were carried out on a high pressure turbine rotor blade cascade in medium flow conditions. Film-cooling effectiveness or degree of cooling was assessed in terms of cooling hole geometry, blowing ratio, freestream turbulence, coolant-to-mainstream density ratio, purge flow rate, upstream vortex for blade platform cooling and blowing ratio, and upstream vortex for blade span cooling. The blade tip study was performed in a blow-down flow loop in a transonic flow environment. The degree of cooling was assessed in terms of blowing ratio and tip clearance. Limited heat transfer coefficient measurements were also carried out. Mainstream pressure loss was also measured for blade platform and blade tip film-cooling with the help of pitot-static probes. The pressure sensitive paint (PSP) and temperature sensitive paint (TSP) techniques were used for measuring film-cooling effectiveness whereas for heat transfer coefficient measurement, temperature sensitive paint (TSP) technique was employed. Results indicated that the blade platform cooling requires a combination of upstream purge flow and downstream discrete film-cooling holes to cool the entire platform. The shaped cooling holes provided wider film coverage and higher film-cooling effectiveness than the cylindrical holes while also creating lesser mainstream pressure losses. Higher coolant-to-mainstream density ratio resulted in higher effectiveness levels from the cooling holes. On the blade span, at any given blowing ratio, the suction side showed better coolant coverage than the pressure side even though the former had two fewer rows of holes. Film-cooling effectiveness increased with blowing ratio on both sides of the blade. Whereas the pressure side effectiveness continued to increase with blowing ratio, the increase in suction side effectiveness slowed down at higher blowing ratios (M=0.9 and 1.2). Upstream wake had a detrimental effect on film coverage. 0% and 25% wake phase positions significantly decreased film-cooling effectiveness magnitude. Comparison between the compound shaped hole and the compound cylindrical hole design showed higher effectiveness values for shaped holes on the suction side. The cylindrical holes performed marginally better in the curved portion of the pressure side. Finally, the concept tip proved to be better than the baseline tip in terms of reducing mainstream flow leakage and mainstream pressure loss. The film-cooling effectiveness on the concept blade increased with increasing blowing ratio and tip gap. However, the film-coverage on the leading tip portion was almost negligible.

Download or read book Local Heat Transfer and Film Effectiveness of a Film Cooled Gas Turbine Blade Tip written by Adedapo Oluyomi Adewusi and published by . This book was released on 1999 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Local Heat Transfer and Effectiveness Measurements on Film Cooled Turbine Blade Tip Models written by Srinath Varadarajan Ekkad and published by . This book was released on 1991 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Study of Gas Turbine Blade Film Cooling and Internal Turbulated Heat Transfer at Large Reynolds Numbers written by Shantanu Mhetras and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Film cooling effectiveness on a gas turbine blade tip on the near tip pressure side and on the squealer cavity floor is investigated. Optimal arrangement of film cooling holes, effect of a full squealer and a cutback squealer, varying blowing ratios and squealer cavity depth are also examined on film cooling effectiveness. The film-cooling effectiveness distributions are measured on the blade tip, near tip pressure side and the inner pressure and suction side rim walls using a Pressure Sensitive Paint (PSP) technique. A blowing ratio of 1.0 is found to give best results on the pressure side whereas the other tip surfaces give best results for blowing ratios of 2. Film cooling effectiveness tests are also performed on the span of a fully-cooled high pressure turbine blade in a 5 bladed linear cascade using the PSP technique. Film cooling effectiveness over the entire blade region is determined from full coverage film cooling, showerhead cooling and from each individual row with and without an upstream wake. The effect of superposition of film cooling effectiveness from each individual row is then compared with full coverage film cooling. Results show that an upstream wake can result in lower film cooling effectiveness on the blade. Effectiveness magnitudes from superposition of effectiveness data from individual rows are comparable with that from full coverage film cooling. Internal heat transfer measurements are also performed in a high aspect ratio channel and from jet array impingement on a turbulated target wall at large Reynolds numbers. For the channel, three dimple and one discrete rib configurations are tested on one of the wide walls for Reynolds numbers up to 1.3 million. The presence of a turbulated wall and its effect on heat transfer enhancement against a smooth surface is investigated. Heat transfer enhancement is found to decrease at high Re with the discrete rib configurations providing the best enhancement but highest pressure losses. Experiments to investigate heat transfer and pressure loss from jet array impingement are also performed on the target wall at Reynolds numbers up to 450,000. The heat transfer from a turbulated target wall and two jet plates is investigated. A target wall with short pins provides the best heat transfer with the dimpled target wall giving the lowest heat transfer among the three geometries studied.