Download or read book Thermodynamic Mechanism of MQL Grinding with Nano Bio lubricant written by Changhe Li and published by Springer Nature. This book was released on 2023-12-01 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the thermodynamic mechanism of MQL grinding with nano-biological lubricant from the force, heat, surface integrity, and micro-morphology. It makes up the fatal defect of the lack of heat transfer capability of traditional MQL grinding. The machining accuracy, surface quality, especially surface integrity of the workpiece, are significantly improved; at the same time, the service life of the grinding wheel is increased and the working environment is improved. The general scope of the book’s content is the effects of MQL grinding with nano-bio-lubricant on grinding force, thermal mechanism, and surface. It provides a new method of sustainable green grinding for environment-friendly, resource-saving, and energy-efficient utilization and solves the technical bottleneck of the insufficient capacity in MQL heat transfer.
Download or read book Thermodynamic Mechanism of Cryogenic Air Minimum Quantity Lubrication Grinding written by Liu, Mingzheng and published by IGI Global. This book was released on 2024-05-02 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: The achievement of high-efficiency and precise grinding of difficult-to-cut metals—like titanium alloys—is essential in the aerospace industry. However, the process often results in thermal damage to the workpiece surface, posing a significant technical challenge. While minimum quantity lubrication (MQL) has been used to aid titanium alloy grinding, its effectiveness is limited by insufficient heat dissipation and lubrication. As an alternative to normal temperature air for carrying micro-lubricants, Cryogenic air has shown promise in improving oil film heat transfer and lubrication performance in the grinding zone, thus reducing workpiece surface thermal damage. The experimental state of the technology demands more comprehensive studies on its effectiveness and on the underlying mechanisms. Thermodynamic Mechanism of Cryogenic Air Minimum Quantity Lubrication Grinding addresses these challenges by providing a theoretical framework for understanding and optimizing cryogenic air minimum quantity lubrication in grinding processes, particularly for titanium alloys. It explores the physical characteristics of lubricants under cryogenic conditions, the influence of low temperatures on atomization effects, droplet formation dynamics, and heat transfer mechanisms within the grinding zone. By establishing quantitative relationships between cryogenic air parameters and lubricant properties, the book lays a foundation for enhancing the cooling lubrication mechanism of cryogenic air MQL in grinding processes. Researchers, scholars, and graduate students in universities and research institutes focusing on machining will find this book invaluable, as it goes beyond the theoretical insights into practical solutions to enhance grinding efficiency and reduce thermal damage.
Download or read book Microfluidics and Nanofluidics written by Mohsen Sheikholeslami Kandelousi and published by BoD – Books on Demand. This book was released on 2018-08-22 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the present book, various applications of microfluidics and nanofluidics are introduced. Microfluidics and nanofluidics span a broad array of disciplines including mechanical, materials, and electrical engineering, surface science, chemistry, physics and biology. Also, this book deals with transport and interactions of colloidal particles and biomolecules in microchannels, which have great importance to many microfluidic applications, such as drug delivery in life science, microchannel heat exchangers in electronic cooling, and food processing industry. Furthermore, this book focuses on a detailed description of the thermal transport behavior, challenges and implications that involve the development and use of HTFs under the influence of atomistic-scale structures and industrial applications.
Download or read book Nanolubricants written by Jean Michel Martin and published by John Wiley & Sons. This book was released on 2008-04-30 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: The technology involved in lubrication by nanoparticles is a rapidly developing scientific area and one that has been watched with interest for the past ten years. Nanolubrication offers a solution to many problems associated with traditional lubricants that contain sulphur and phosphorus; and though for some time the production of nanoparticles was restricted by the technologies available, today synthesis methods have been improved to such a level that it is possible to produce large quantities relatively cheaply and efficiently. Nanolubricants develops a new concept of lubrication, based on these nanoparticles, and along with the authors’ own research it synthesises the information available on the topic of nanolubrication from existing literature and presents it in a concise form. Describes the many advantages and potential applications of nanotechnology in the tribological field. Offers a full review of the state-of-the-art as well as much original research that is yet unpublished. Includes sections on boundary lubrication by colloïdal systems, nanolubricants made of metal dichalcogenides, carbon-based nanolubricants, overbased detergent salts, nanolubricants made of metals and boron-based solid nanolubricants and lubrication additives. Authored by highly regarded experts in the field with contributions from leading international academics. Nanolubricants will appeal to postgraduate students, academics and researchers in mechanical engineering, chemical engineering and materials science. It should also be of interest to practising engineers with petroleum companies and mechanical manufacturers.
Download or read book Environmentally Conscious Manufacturing written by Myer Kutz and published by John Wiley & Sons. This book was released on 2007-03-16 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second volume of the Wiley series, Environmentally Conscious Manufacturing focuses on environmentally preferable approaches to manufacturing. Contributors present and discuss the technologies engineers need to specify and employ to make manufacturing operations environmentally friendly and conform to environmental regulations. Chapters cover Hazardous Waste Minimization and Management; Cost-Effective Manufacturing; Real-time Process Monitoring and Control; Ethics in ECM; Governmental Regulations and Policies, and Total Quality Management. In each chapter case studies are provided to guide readers in areas outside their expertise.
Download or read book Advances in Microfluidic Technologies for Energy and Environmental Applications written by Yong Ren and published by BoD – Books on Demand. This book was released on 2020-05-20 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: Microfluidics have aroused a new surge of interest in recent years in environmental and energy areas, and inspired novel applications to tackle the worldwide challenges for sustainable development. This book aims to present readers with a valuable compendium of significant advances in applying the multidisciplinary microfluidic technologies to address energy and environmental problems in a plethora of areas such as environmental monitoring and detection, new nanofluid application in traditional mechanical manufacturing processes, development of novel biosensors, and thermal management. This book will provide a new perspective to the understanding of the ever-growing importance of microfluidics.
Download or read book Hybrid Nanofluids written by Zafar Said and published by Elsevier. This book was released on 2022-01-28 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hybrid Nanofluids: Preparation, Characterization and Applications presents the history of hybrid nanofluids, preparation techniques, thermoelectrical properties, rheological behaviors, optical properties, theoretical modeling and correlations, and the effect of all these factors on potential applications, such as solar energy, electronics cooling, heat exchangers, machining, and refrigeration. Future challenges and future work scope have also been included. The information from this book enables readers to discover novel techniques, resolve existing research limitations, and create novel hybrid nanofluids which can be implemented for heat transfer applications. Describes the characterization, thermophysical and electrical properties of nanofluids Assesses parameter selection and property measurement techniques for the calibration of thermal performance Provides information on theoretical models and correlations for predicting hybrid nanofluids properties from experimental properties
Download or read book Analysis of Machining and Machine Tools written by Steven Liang and published by Springer. This book was released on 2015-12-29 with total page 241 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides readers with the fundamental, analytical, and quantitative knowledge of machining process planning and optimization based on advanced and practical understanding of machinery, mechanics, accuracy, dynamics, monitoring techniques, and control strategies that they need to understanding machining and machine tools. It is written for first-year graduate students in mechanical engineering, and is also appropriate for use as a reference book by practicing engineers. It covers topics such as single and multiple point cutting processes; grinding processes; machine tool components, accuracy, and metrology; shear stress in cutting, cutting temperature and thermal analysis, and machine tool chatter. The second section of the book is devoted to “Non-Traditional Machining,” where readers can find chapters on electrical discharge machining, electrochemical machining, laser and electron beam machining, and biomedical machining. Examples of realistic problems that engineers are likely to face in the field are included, along with solutions and explanations that foster a didactic learning experience.
Download or read book Nanobiosensors written by Alexandru Grumezescu and published by Academic Press. This book was released on 2016-09-28 with total page 928 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanobiosensors: Nanotechnology in the Agri-Food Industry, Volume 8, provides the latest information on the increasing demand for robust, rapid, inexpensive, and safe alternative technologies that monitor, test, and detect harmful or potentially dangerous foods. Due to their high sensitivity and selectivity, nanobiosensors have attracted attention for their use in monitoring not only biological contaminants in food, but also potential chemical and physical hazards. This book offers a broad overview regarding the current progress made in the field of nanosensors, including cutting-edge technological progress and the impact of these devices on the food industry. Special attention is given to the detection of microbial contaminants and harmful metabolotes, such as toxins and hormones, which have a great impact on both humans and animal health and feed. - Includes the most up-to-date information on nanoparticles based biosensors and quantum dots for biological detection - Provides application methods and techniques for research analysis for bacteriological detection and food testing - Presents studies using analytical tools to improve food safety and quality analysis
Download or read book Sustainable Machining written by J. Paulo Davim and published by Springer. This book was released on 2017-03-19 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an overview on current sustainable machining. Its chapters cover the concept in economic, social and environmental dimensions. It provides the reader with proper ways to handle several pollutants produced during the machining process. The book is useful on both undergraduate and postgraduate levels and it is of interest to all those working with manufacturing and machining technology.
Download or read book Advances in Manufacturing and Industrial Engineering written by Ranganath M. Singari and published by Springer Nature. This book was released on 2021-01-13 with total page 1180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents selected peer reviewed papers from the International Conference on Advanced Production and Industrial Engineering (ICAPIE 2019). It covers a wide range of topics and latest research in mechanical systems engineering, materials engineering, micro-machining, renewable energy, industrial and production engineering, and additive manufacturing. Given the range of topics discussed, this book will be useful for students and researchers primarily working in mechanical and industrial engineering, and energy technologies.
Download or read book Advances in Micro and Nano Manufacturing and Surface Engineering written by M. S. Shunmugam and published by Springer Nature. This book was released on 2019-11-30 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents research papers on micro and nano manufacturing and surface engineering which were presented during the 7th International and 28th All India Manufacturing Technology, Design and Research conference 2018 (AIMTDR 2018). The papers discuss the latest advances in miniature manufacturing, the machining of miniature components and features as well as improvement of surface properties. This volume will be of interest to academicians, researchers, and practicing engineers alike.
Download or read book Vegetable Oil based Bio lubricants and Transformer Fluids written by Dhorali Gnanasekaran and published by Springer. This book was released on 2017-09-08 with total page 163 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses vegetable oil based biolubricants and their applications in the power distribution industry. Vegetable oil based lubricants offer significant advantages over petroleum-based lubricants, including biodegradability, cost-effectiveness, renewability, and lower environmental effects. This book provides a detailed literature survey of modified vegetable oils. It discusses the physical and chemical properties of vegetable oil, and their effects on its applications in tribology. The book discusses additives and enhancements to make vegetable oils suitable for use as lubricating oils and transformer oils in power plants and power distribution grids. The contents of the book will be useful to researchers and professionals as well as policy makers and standards agencies.
Download or read book Advances in Applied Mechanical Engineering written by Hari Kumar Voruganti and published by Springer Nature. This book was released on 2020-02-01 with total page 1161 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents select peer reviewed proceedings of the International Conference on Applied Mechanical Engineering Research (ICAMER 2019). The books examines various areas of mechanical engineering namely design, thermal, materials, manufacturing and industrial engineering covering topics like FEA, optimization, vibrations, condition monitoring, tribology, CFD, IC engines, turbo-machines, automobiles, manufacturing processes, machining, CAM, additive manufacturing, modelling and simulation of manufacturing processing, optimization of manufacturing processing, supply chain management, and operations management. In addition, recent studies on composite materials, materials characterization, fracture and fatigue, advanced materials, energy storage, green building, phase change materials and structural change monitoring are also covered. Given the contents, this book will be useful for students, researchers and professionals working in mechanical engineering and allied fields.
Download or read book Machining of Titanium Alloys written by J. Paulo Davim and published by Springer. This book was released on 2014-07-05 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a collection of examples illustrating the resent research advances in the machining of titanium alloys. These materials have excellent strength and fracture toughness as well as low density and good corrosion resistance; however, machinability is still poor due to their low thermal conductivity and high chemical reactivity with cutting tool materials. This book presents solutions to enhance machinability in titanium-based alloys and serves as a useful reference to professionals and researchers in aerospace, automotive and biomedical fields.
Download or read book Lubricants and Lubrication 2 Volume Set written by Theo Mang and published by John Wiley & Sons. This book was released on 2017-05-08 with total page 1220 pages. Available in PDF, EPUB and Kindle. Book excerpt: Praise for the previous edition: "Contains something for everyone involved in lubricant technology." —Chemistry & Industry This completely revised third edition incorporates the latest data available and reflects the knowledge of one of the largest companies active in the business. The authors take into account the interdisciplinary character of the field, considering aspects of engineering, materials science, chemistry, health and safety. The result is a volume providing chemists and engineers with a clear interdisciplinary introduction and guide to all major lubricant applications, focusing not only on the various products but also on specific application engineering criteria. A classic reference work, completely revised and updated (approximately 35% new material) focusing on sustainability and the latest developments, technologies and processes of this multi billion dollar business Provides chemists and engineers with a clear interdisciplinary introduction and guide to all major lubricant applications, looking not only at the various products but also at specific application engineering criteria All chapters are updated in terms of environmental and operational safety. New guidelines, such as REACH, recycling alternatives and biodegradable base oils are introduced Discusses the integration of micro- and nano-tribology and lubrication systems Reflects the knowledge of Fuchs Petrolub SE, one of the largest companies active in the lubrication business 2 Volumes wileyonlinelibrary.com/ref/lubricants
Download or read book Materials Design and Manufacturing for Sustainable Environment written by Santhakumar Mohan and published by Springer Nature. This book was released on 2021-02-06 with total page 909 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises the select proceedings of the International Conference on Materials, Design and Manufacturing for Sustainable Environment (ICMDMSE 2020). The primary focus is on emerging materials and cutting-edge manufacturing technologies for sustainable environment. The book covers a wide range of topics such as advanced materials, vibration, tribology, finite element method (FEM), heat transfer, fluid mechanics, energy engineering, additive manufacturing, robotics and automation, automobile engineering, industry 4.0, MEMS and nanotechnology, optimization techniques, condition monitoring, and new paradigms in technology management. Contents of this book will be useful to students, researchers, and practitioners alike.
