Download or read book Reliability of Organic Compounds in Microelectronics and Optoelectronics written by Willem Dirk van Driel and published by Springer Nature. This book was released on 2022-01-31 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book aims to provide a comprehensive reference into the critical subject of failure and degradation in organic materials, used in optoelectronics and microelectronics systems and devices. Readers in different industrial sectors, including microelectronics, automotive, lighting, oil/gas, and petrochemical will benefit from this book. Several case studies and examples are discussed, which readers will find useful to assess and mitigate similar failure cases. More importantly, this book presents methodologies and useful approaches in analyzing a failure and in relating a failure to the reliability of materials and systems.

Download or read book Advanced Computational Methods and Experiments in Heat Transfer X written by Bengt Sundén and published by WIT Press. This book was released on 2008-06-19 with total page 241 pages. Available in PDF, EPUB and Kindle. Book excerpt: In engineering design and development, reliable and accurate computational methods are requested to replace or complement expensive and time consuming experimental trial and error work. Tremendous advancements have been achieved during recent years due to improved numerical solutions of non-linear partial differential equations and computer developments to achieve efficient and rapid calculations. Nevertheless, to further progress in computational methods will require developments in theoretical and predictive procedures – both basic and innovative – and in applied research. Accurate experimental investigations are needed to validate the numerical calculations. This book contains the edited versions of the papers presented at the Tenth International Conference on Advanced Computational Methods and Experimental Measurements in Heat Transfer and Mass Transfer held in Maribor, Slovenia in July 2008. The objective of this conference series is to provide a forum for presentation and discussion of advanced topics, new approaches and application of advanced computational methods and experimental measurements to heat and mass transfer problems. The contributed papers are grouped in the following appropriate sections to provide better access for readers: Natural and forced convection; Heat exchangers; Advances in computational methods; Heat recovery; Heat transfer; Modelling and experiments.

Download or read book Mechanics of Microsystems written by Alberto Corigliano and published by John Wiley & Sons. This book was released on 2017-11-20 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanics of Microsystems Alberto Corigliano, Raffaele Ardito, Claudia Comi, Attilio Frangi, Aldo Ghisi and Stefano Mariani, Politecnico di Milano, Italy A mechanical approach to microsystems, covering fundamental concepts including MEMS design, modelling and reliability Mechanics of Microsystems takes a mechanical approach to microsystems and covers fundamental concepts including MEMS design, modelling and reliability. The book examines the mechanical behaviour of microsystems from a ‘design for reliability’ point of view and includes examples of applications in industry. Mechanics of Microsystems is divided into two main parts. The first part recalls basic knowledge related to the microsystems behaviour and offers an overview on microsystems and fundamental design and modelling tools from a mechanical point of view, together with many practical examples of real microsystems. The second part covers the mechanical characterization of materials at the micro-scale and considers the most important reliability issues (fracture, fatigue, stiction, damping phenomena, etc) which are fundamental to fabricate a real working device. Key features: Provides an overview of MEMS, with special focus on mechanical-based Microsystems and reliability issues. Includes examples of applications in industry. Accompanied by a website hosting supplementary material. The book provides essential reading for researchers and practitioners working with MEMS, as well as graduate students in mechanical, materials and electrical engineering.

Download or read book Practical Guide to RF MEMS written by Jacopo Iannacci and published by John Wiley & Sons. This book was released on 2013-08-12 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: Closes the gap between hardcore-theoretical and purely experimental RF-MEMS books. The book covers, from a practical viewpoint, the most critical steps that have to be taken in order to develop novel RF-MEMS device concepts. Prototypical RF-MEMS devices, both including lumped components and complex networks, are presented at the beginning of the book as reference examples, and these are then discussed from different perspectives with regard to design, simulation, packaging, testing, and post-fabrication modeling. Theoretical concepts are introduced when necessary to complement the practical hints given for all RF-MEMS development stages. Provides researchers and engineers with invaluable practical hints on how to develop novel RF-MEMS device concepts Covers all critical steps, dealing with design, simulation, optimization, characterization and fabrication of MEMS for radio-frequency applications Addresses frequently disregarded issues, explicitly treating the hard to predict interplay between the three-dimensional device structure and its electromagnetic functionality Bridges theory and experiment, fundamental concepts are introduced with the application in mind, and simulation results are validated against experimental results Appeals to the practice-oriented R&D reader: design and simulation examples are based on widely known software packages such as ANSYS and the hardware description language Verilog.

Download or read book Advanced RF MEMS written by Stepan Lucyszyn and published by Cambridge University Press. This book was released on 2010-08-19 with total page 441 pages. Available in PDF, EPUB and Kindle. Book excerpt: An up-to-date guide to the theory and applications of RF MEMS. With detailed information about RF MEMS technology as well as its reliability and applications, this is a comprehensive resource for professionals, researchers, and students alike. • Reviews RF MEMS technologies • Illustrates new techniques that solve long-standing problems associated with reliability and packaging • Provides the information needed to incorporate RF MEMS into commercial products • Describes current and future trends in RF MEMS, providing perspective on industry growth • Ideal for those studying or working in RF and microwave circuits, systems, microfabrication and manufacturing, production management and metrology, and performance evaluation

Download or read book Experimental and Applied Mechanics Volume 6 written by Tom Proulx and published by Springer Science & Business Media. This book was released on 2011-06-01 with total page 859 pages. Available in PDF, EPUB and Kindle. Book excerpt: This the sixth volume of six from the Annual Conference of the Society for Experimental Mechanics, 2010, brings together 128 chapters on Experimental and Applied Mechanics. It presents early findings from experimental and computational investigations including High Accuracy Optical Measurements of Surface Topography, Elastic Properties of Living Cells, Standards for Validating Stress Analyses by Integrating Simulation and Experimentation, Efficiency Enhancement of Dye-sensitized Solar Cell, and Blast Performance of Sandwich Composites With Functionally Graded Core.

Download or read book Molecular Modeling and Multiscaling Issues for Electronic Material Applications written by Artur Wymyslowski and published by Springer. This book was released on 2014-11-20 with total page 203 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers readers a snapshot of the progression of molecular modeling in the electronics industry and how molecular modeling is currently being used to understand materials to solve relevant issues in this field. The reader is introduced to the evolving role of molecular modeling, especially seen from the perspective of the IEEE community and modeling in electronics. This book also covers the aspects of molecular modeling needed to understand the relationship between structures and mechanical performance of materials. The authors also discuss the transitional topic of multiscale modeling and recent developments on the atomistic scale and current attempts to reach the submicron scale, as well as the role that quantum mechanics can play in performance prediction.

Download or read book Proceedings of Mechanical Engineering Research Day 2020 written by Mohd Fadzli Bin Abdollah and published by Centre for Advanced Research on Energy. This book was released on 2020-12-01 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: This e-book is a compilation of 170 articles presented at the 7th Mechanical Engineering Research Day (MERD'20) - Kampus Teknologi UTeM (virtual), Melaka, Malaysia on 16 December 2020.

Download or read book Microfabrication for Industrial Applications written by Regina Luttge and published by William Andrew. This book was released on 2011-09-14 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: Microfabrication for Industrial Applications focuses on the industrial perspective for micro- and nanofabrication methods including large-scale manufacturing, transfer of concepts from lab to factory, process tolerance, yield, robustness, and cost. It gives a history of miniaturization, micro- and nanofabrication, and surveys industrial fields of application, illustrating fabrication processes of relevant micro and nano devices. Concerning sub-micron feature manufacture, the book explains: the philosophy of micro/ nanofabrication for integrated circuit industry; thin film deposition; (waveguide, plastic, semiconductor) material processing; packaging; interconnects; stress (e.g., thin film residual); economic; and environmental aspects. Micro/nanomechanical sensors and actuators are explained in depth with information on applications, materials (incl. functional polymers), methods, testing, fabrication, integration, reliability, magnetic microstructures, etc. Shows engineers & students how to evaluate the potential value of current and nearfuture manufacturing processes for miniaturized systems in industrial environments Explains the top-down and bottom up approaches to nanotechnology, nanostructures fabricated with beams, nano imprinting methods, nanoparticle manufacturing (and their health aspects), nanofeature analysis, and connecting nano to micro to macro Discusses issues for practical application cases; possibilities of dimension precision; large volume manufacturing of micro- & nanostructures (machines, materials, costs) Explains applications of Microsystems for information technology, e.g.: data recording (camera, microphone), storage (memories, CDs), communication; computing; and displays (beamers, LCD, TFT) Case studies are given for sensors, resonators, probes, transdermal medical systems, micro- pumps & valves, inkjets, DNA-analysis, lab-on-a-chip, & micro-cooling

Download or read book Thermal Modelling of Power Transformers Using Computational Fluid Dynamics written by Saeed Khandan Siar and published by BoD – Books on Demand. This book was released on 2024-09-19 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power transformers have become vital equipment in providing sustainable power networks and minimizing thermal stress is essential for enhancing their lifespan and reliability. This thesis uses Computational Fluid Dynamics (CFD) to analyze the thermal behavior of power transformers. It examines the effects of non-uniform heat loss distributions and analyses both steady-state and transient thermal behavior in natural and forced cooling modes. It is vital to calculate the hot spot factor under various conditions, especially during transient cooling condition. This research addresses how different parameters impact the hot spot factor and temperature distribution at different operating condition, using measurements and CFD simulations to identify the optimal cooling designs.

Download or read book Thermal Management for LED Applications written by Clemens J.M. Lasance and published by Springer Science & Business Media. This book was released on 2013-09-17 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal Management for LED Applications provides state-of-the-art information on recent developments in thermal management as it relates to LEDs and LED-based systems and their applications. Coverage begins with an overview of the basics of thermal management including thermal design for LEDs, thermal characterization and testing of LEDs, and issues related to failure mechanisms and reliability and performance in harsh environments. Advances and recent developments in thermal management round out the book with discussions on advances in TIMs (thermal interface materials) for LED applications, advances in forced convection cooling of LEDs, and advances in heat sinks for LED assemblies.

Download or read book Thermal and Electro thermal System Simulation 2020 written by Márta Rencz and published by MDPI. This book was released on 2021-01-12 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book, edited by Prof. Marta Rencz and Prof Andras Poppe, Budapest University of Technology and Economics, and by Prof. Lorenzo Codecasa, Politecnico di Milano, collects fourteen papers carefully selected for the “thermal and electro-thermal system simulation” Special Issue of Energies. These contributions present the latest results in a currently very “hot” topic in electronics: the thermal and electro-thermal simulation of electronic components and systems. Several papers here proposed have turned out to be extended versions of papers presented at THERMINIC 2019, which was one of the 2019 stages of choice for presenting outstanding contributions on thermal and electro-thermal simulation of electronic systems. The papers proposed to the thermal community in this book deal with modeling and simulation of state-of-the-art applications which are highly critical from the thermal point of view, and around which there is great research activity in both industry and academia. In particular, contributions are proposed on the multi-physics simulation of families of electronic packages, multi-physics advanced modeling in power electronics, multiphysics modeling and simulation of LEDs, batteries and other micro and nano-structures.

Download or read book Prognostics and Health Management of Electronics written by Michael G. Pecht and published by John Wiley & Sons. This book was released on 2018-08-15 with total page 809 pages. Available in PDF, EPUB and Kindle. Book excerpt: An indispensable guide for engineers and data scientists in design, testing, operation, manufacturing, and maintenance A road map to the current challenges and available opportunities for the research and development of Prognostics and Health Management (PHM), this important work covers all areas of electronics and explains how to: assess methods for damage estimation of components and systems due to field loading conditions assess the cost and benefits of prognostic implementations develop novel methods for in situ monitoring of products and systems in actual life-cycle conditions enable condition-based (predictive) maintenance increase system availability through an extension of maintenance cycles and/or timely repair actions; obtain knowledge of load history for future design, qualification, and root cause analysis reduce the occurrence of no fault found (NFF) subtract life-cycle costs of equipment from reduction in inspection costs, downtime, and inventory Prognostics and Health Management of Electronics also explains how to understand statistical techniques and machine learning methods used for diagnostics and prognostics. Using this valuable resource, electrical engineers, data scientists, and design engineers will be able to fully grasp the synergy between IoT, machine learning, and risk assessment.

Download or read book Handbook of Silicon Based MEMS Materials and Technologies written by Markku Tilli and published by Elsevier. This book was released on 2020-04-17 with total page 1028 pages. Available in PDF, EPUB and Kindle. Book excerpt: Handbook of Silicon Based MEMS Materials and Technologies, Third Edition is a comprehensive guide to MEMS materials, technologies, and manufacturing with a particular emphasis on silicon as the most important starting material used in MEMS. The book explains the fundamentals, properties (mechanical, electrostatic, optical, etc.), materials selection, preparation, modeling, manufacturing, processing, system integration, measurement, and materials characterization techniques of MEMS structures. The third edition of this book provides an important up-to-date overview of the current and emerging technologies in MEMS making it a key reference for MEMS professionals, engineers, and researchers alike, and at the same time an essential education material for undergraduate and graduate students. - Provides comprehensive overview of leading-edge MEMS manufacturing technologies through the supply chain from silicon ingot growth to device fabrication and integration with sensor/actuator controlling circuits - Explains the properties, manufacturing, processing, measuring and modeling methods of MEMS structures - Reviews the current and future options for hermetic encapsulation and introduces how to utilize wafer level packaging and 3D integration technologies for package cost reduction and performance improvements - Geared towards practical applications presenting several modern MEMS devices including inertial sensors, microphones, pressure sensors and micromirrors

Download or read book Proceedings of Mechanical Engineering Research Day 2019 written by Mohd Fadzli Bin Abdollah and published by Centre for Advanced Research on Energy. This book was released on 2019-08-05 with total page 395 pages. Available in PDF, EPUB and Kindle. Book excerpt: This e-book is a compilation of papers presented at the 6th Mechanical Engineering Research Day (MERD'19) - Kampus Teknologi UTeM, Melaka, Malaysia on 31 July 2019.

Download or read book 3D Microelectronic Packaging written by Yan Li and published by Springer. This book was released on 2017-01-20 with total page 465 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume provides a comprehensive reference for graduate students and professionals in both academia and industry on the fundamentals, processing details, and applications of 3D microelectronic packaging, an industry trend for future microelectronic packages. Chapters written by experts cover the most recent research results and industry progress in the following areas: TSV, die processing, micro bumps, direct bonding, thermal compression bonding, advanced materials, heat dissipation, thermal management, thermal mechanical modeling, quality, reliability, fault isolation, and failure analysis of 3D microelectronic packages. Numerous images, tables, and didactic schematics are included throughout. This essential volume equips readers with an in-depth understanding of all aspects of 3D packaging, including packaging architecture, processing, thermal mechanical and moisture related reliability concerns, common failures, developing areas, and future challenges, providing insights into key areas for future research and development.

Download or read book Nano and Microfabrication for Industrial and Biomedical Applications written by Regina Luttge and published by William Andrew. This book was released on 2016-06-12 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nano- and Microfabrication for Industrial and Biomedical Applications, Second Edition, focuses on the industrial perspective on micro- and nanofabrication methods, including large-scale manufacturing, the transfer of concepts from lab to factory, process tolerance, yield, robustness, and cost. The book gives a history of miniaturization and micro- and nanofabrication, and surveys industrial fields of application, illustrating fabrication processes of relevant micro and nano devices. In this second edition, a new focus area is nanoengineering as an important driver for the rise of novel applications by integrating bio-nanofabrication into microsystems. In addition, new material covers lithographic mould fabrication for soft-lithography, nanolithography techniques, corner lithography, advances in nanosensing, and the developing field of advanced functional materials. Luttge also explores the view that micro- and nanofabrication will be the key driver for a "tech-revolution" in biology and medical research that includes a new case study that covers the developing organ-on-chip concept. - Presents an interdisciplinary approach that makes micro/nanofabrication accessible equally to engineers and those with a life science background, both in academic settings and commercial R&D - Provides readers with guidelines for assessing the commercial potential of any new technology based on micro/nanofabrication, thus reducing the investment risk - Updated edition presents nanoengineering as an important driver for the rise of novel applications by integrating bio-nanofabrication into microsystems