Download or read book Thermal Expansion of SNAP Materials written by J. D. Watrous and published by . This book was released on 1961 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal expansion characteristics were determined for the fuel-moderator, reflector, cladding, and engineering materials within the SNAP-2 core vessel. Values were determined for AISI Type 347 stainless steel, Hastelloy N, beryllium, zirconium, zirconium hydride, and zirconium-uranium hydrides, from room temperature to temperatures greater than 1300°F. Derived equations were calculated for these materials, using a least squares analysis.
Download or read book Thermal Expansion of Snap Materials written by and published by . This book was released on 1961 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal expansion characteristics were determined for fuel-moderator, reflector, cladding, and engineering erials within the SNAP-2 core vessel. Values were denined for AISI Type 347 stainless steel, Hastelloy N, Zr, ZrH, and zirconium --uranium hydrides, from room temperature to temperatures greater than 1300 deg F. Derived equations were calculated for these materials, using a least squares analysis. Thermal expansion coefficients for the temperature range of 77 to 1200 deg F are: 10.34 x 106 in./ in./ deg F, for Type 347 stainless steel; 7.46 x 10−6 in./in./ deg F, for Hastelloy N; 9.07 x 10/sup ->/ in./ in./ deg F, for Be; and 6.12 x 10−6 in-/in./ deg F, for Zr--7 wt% UH with an N = 6.4. (auth).
Download or read book Systems for Nuclear Auxiliary Power SNAP written by and published by . This book was released on 1964 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Expansion of Solids written by Cho Yen Ho and published by ASM International. This book was released on 1998-01-01 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a detailed examination of theory and techniques in thermal expansion of solids. Subjects include a generalized theory, estimation techniques and selected effects, temperature measurements in solids, thermal expansion by X-ray diffraction, high sensitivity expansivity measurement techniques,
Download or read book TID written by and published by . This book was released on 1961 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Expansion written by Y. S. Touloukian and published by Springer. This book was released on 1975 with total page 1458 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The volume comprises three major sections: The front text on theory, estimation, and measurement together with its bibliography, the main body of numerical data with its references, and the material index."--Intro. Highly accurate and technical data. Published 1975.
Download or read book Metal Hydrides written by William M. Mueller and published by Elsevier. This book was released on 2013-09-12 with total page 804 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Hydrides focuses on the theories of hydride formation as well as on experimental procedures involved in the formation of hydrides, the reactions that occur between hydrides and other media, and the physical and mechanical properties of the several classes of hydrides. The use of metal hydrides in the control of neutron energies is discussed, as are many other immediate or potential uses, e.g., in the production of high-purity hydrogen and in powder metallurgy. It is hoped that this book will serve as a valuable reference to students, research professors, and industrial researchers in metal hydrides and in allied fields. Selected chapters may serve specialists in other fields as an introduction to metal hydrides. The information contained herein will also be of lasting and practical value to the metallurgist, inorganic chemist, solid-state physicist, nuclear engineer, and others working with chemical or physical processes involving metal-hydrogen systems.
Download or read book Direct Energy Conversion Devices written by and published by . This book was released on 1961 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt: Included are 344 unclassified references on devices utilizing nuclear energy in the production of auxiliary power. The coverage includes nuclear batteries, thermoelectric cells, thermionic cells, and all phases of the SNAP program, although not all SNAP devices employ direct conversion. References from Nuclear Science Abstracts (NSA) through December 15, 1961, are included.
Download or read book Injection Moulding Materials written by A. Whelan and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to make the subject manageable the term 'injection moulding' has been restricted in its use so that only those processes which rely on thermal softening of the polymeric materials have been described and discussed in this book. It is intended to discuss the subject of reaction injection moulding in a separate book. However, even with this omission, the subject is still a very large one as nowadays many sorts or types of polymers are injection moulded. For example, it is estimated that one-third of all plastics materials are injection moulded-the range of products produced is enormous and increases daily. Because most moulding materials are based on plastics, in particular thermoplastics, the materials guides which form a large part of this book concentrate on the moulding of thermoplastics materials. Such guides should only be treated as general guidelines as each of the materials is normally available in a wide range of grades. These may differ in polymer molecular weight, molecular weight distribution, the additives used and their concentration, the physical form of the moulding compound, etc. A wide range of processing behaviours and end-use properties is therefore possible from any of the materials listed. This versatility is typified by the rubbery polymers which are compounded into an incredibly wide range of compounds. Because of this versatility only a very general guideline has been given for such materials.
Download or read book Reactor Materials written by and published by . This book was released on 1967 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NASA Technical Note written by and published by . This book was released on 1961 with total page 474 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Properties of High temperature Materials written by W. D. Wood and published by . This book was released on 1964 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report is a compilation of specific heat, thermal expansion, and thermal conductivity data for materials of possible structural usefulness above 2500 F. Data are presented graphically with notations as to measurement methods and test conditions. Prominent laboratories currently making thermal property measurements are identified. (Author).
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1974 with total page 1298 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Plastics Materials and Processes written by Charles A. Harper and published by John Wiley & Sons. This book was released on 2003-10-10 with total page 1008 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plastics Materials and Processes: A Concise Encyclopedia is a resource for anyone with an interest in plastic materials and processes, from seasoned professionals to laypeople. Arranged in alphabetical order, it clearly explains all of the materials and processes as well as their major application areas and usages. Plastics Materials and Processes: A Concise Encyclopedia: Discusses and describes applications and practical uses of the materials and processes. Clear definitions and sufficient depth to satisfy the information seekers needs
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1988 with total page 666 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
Download or read book Joining of Materials and Structures written by Robert W. Messler and published by Elsevier. This book was released on 2004-08-24 with total page 815 pages. Available in PDF, EPUB and Kindle. Book excerpt: Joining of Materials and Structures is the first and only complete and highly readable treatment of the options for joining conventional materials and the structures they comprise in conventional and unconventional ways, and for joining emerging materials and structures in novel ways. Joining by mechanical fasteners, integral designed-or formed-in features, adhesives, welding, brazing, soldering, thermal spraying, and hybrid processes are addressed as processes and technologies, as are issues associated with the joining of metals, ceramics (including cement and concrete) glass, plastics, and composites (including wood), as well as, for the first time anywhere, living tissue. While focused on materials issues, issues related to joint design, production processing, quality assurance, process economics, and joint performance in service are not ignored. The book is written for engineers, from an in-training student to a seasoned practitioner by an engineer who chose to teach after years of practice. By reading and referring to this book, the solutions to joining problems will be within one's grasp.Key Features:·Unprecedented coverage of all joining options (from lashings to lasers) in 10 chapters·Uniquely complete coverage of all materials, including living tissues, in 6 chapters·Richly illustrated with 76 photographs and 233 illustrations or plots·Practice Questions and Problems for use as a text of for reviewing to aid for comprehension* Coverage all of major joining technologies, including welding, soldering, brazing, adhesive and cement bonding, pressure fusion, riveting, bolting, snap-fits, and more* Organized by both joining techniques and materials types, including metals, non-metals, ceramics and glasses, composites, biomaterials, and living tissue* An ideal reference for design engineers, students, package and product designers, manufacturers, machinists, materials scientists
Download or read book DeGarmo s Materials and Processes in Manufacturing written by J. T. Black and published by John Wiley & Sons. This book was released on 2020-07-21 with total page 902 pages. Available in PDF, EPUB and Kindle. Book excerpt: Guiding engineering and technology students for over five decades, DeGarmo's Materials and Processes in Manufacturing provides a comprehensive introduction to manufacturing materials, systems, and processes. Coverage of materials focuses on properties and behavior, favoring a practical approach over complex mathematics; analytical equations and mathematical models are only presented when they strengthen comprehension and provide clarity. Material production processes are examined in the context of practical application to promote efficient understanding of basic principles, and broad coverage of manufacturing processes illustrates the mechanisms of each while exploring their respective advantages and limitations. Aiming for both accessibility and completeness, this text offers introductory students a comprehensive guide to material behavior and selection, measurement and inspection, machining, fabrication, molding, fastening, and other important processes using plastics, ceramics, composites, and ferrous and nonferrous metals and alloys. This extensive overview of the field gives students a solid foundation for advanced study in any area of engineering, manufacturing, and technology.
