Download or read book The Effect of Laser Power and Scan Speed on Melt Pool Characteristics of Pure Titanium and Ti 6Al 4V Alloy for Selective Laser Melting written by Chandrakanth Kusuma and published by . This book was released on 2016 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selective Laser Melting (SLM) is an additive manufacturing (AM) technique that creates complex parts by selectively melting metal powder layer-by-layer. In SLM, the process parameters decide the quality of the fabricated component. In this study, single beads of commercially pure titanium (CP-Ti) and Ti-6Al-4V alloy are melted on a substrate of the same material as powder using an in-house built SLM machine. Multiple combinations of laser power and scan speed are used for single bead fabrication while the laser beam diameter and powder layer thickness are kept constant. This experimental study investigates the influence of laser power, scan speed and laser energy density on the melt pool formation, surface morphology, geometry (width, depth, and height) and hardness of melt pools. The results show that the quality, geometry, and hardness of melt pool is significantly affected by laser power, scanning speed and laser energy density. In addition, the observed unfavorable effects such as inconsistent melt pool formation, balling, porosity are discussed in detail. At the end, suggestions are provided to use optimal parameters to avoid such unfavorable effects.

Download or read book Quality Analysis of Additively Manufactured Metals written by Javad Kadkhodapour and published by Elsevier. This book was released on 2022-11-30 with total page 858 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quality Analysis of Additively Manufactured Metals: Simulation Approaches, Processes, and Microstructure Properties provides readers with a firm understanding of the failure and fatigue processes of additively manufactured metals. With a focus on computational methods, the book analyzes the process-microstructure-property relationship of these metals and how it affects their quality while also providing numerical, analytical, and experimental data for material design and investigation optimization. It outlines basic additive manufacturing processes for metals, strategies for modeling the microstructural features of metals and how these features differ based on the manufacturing process, and more.Improvement of additively manufactured metals through predictive simulation methods and microdamage and micro-failure in quasi-static and cyclic loading scenarios are covered, as are topology optimization methods and residual stress analysis techniques. The book concludes with a section featuring case studies looking at additively manufactured metals in automotive, biomedical and aerospace settings. - Provides insights and outlines techniques for analyzing why additively manufactured metals fail and strategies for avoiding those failures - Defines key terms and concepts related to the failure analysis, quality assurance and optimization processes of additively manufactured metals - Includes simulation results, experimental data and case studies

Download or read book Advances in Computational Methods in Manufacturing written by R. Ganesh Narayanan and published by Springer Nature. This book was released on 2019-10-17 with total page 1092 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents a selection of papers from the 2nd International Conference on Computational Methods in Manufacturing (ICCMM 2019). The papers cover the recent advances in computational methods for simulating various manufacturing processes like machining, laser welding, laser bending, strip rolling, surface characterization and measurement. Articles in this volume discuss both the development of new methods and the application and efficacy of existing computational methods in manufacturing sector. This volume will be of interest to researchers in both industry and academia working on computational methods in manufacturing.

Download or read book Innovations in Additive Manufacturing written by M. Adam Khan and published by Springer Nature. This book was released on 2022-01-31 with total page 343 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the history, fundamentals, process development, applications, post-processing, and experimental results from additive manufacturing. The chapters cover surface treatments, modification, advancements in heat treatment, mechanical hardening and its effect on the material properties. This book also presents content on simulation, modeling, and optimization of materials processing and surface engineering techniques.

Download or read book Additive Manufacturing Technologies written by Ian Gibson and published by Springer. This book was released on 2014-11-26 with total page 509 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers in detail the various aspects of joining materials to form parts. A conceptual overview of rapid prototyping and layered manufacturing is given, beginning with the fundamentals so that readers can get up to speed quickly. Unusual and emerging applications such as micro-scale manufacturing, medical applications, aerospace, and rapid manufacturing are also discussed. This book provides a comprehensive overview of rapid prototyping technologies as well as support technologies such as software systems, vacuum casting, investment casting, plating, infiltration and other systems. This book also: Reflects recent developments and trends and adheres to the ASTM, SI, and other standards Includes chapters on automotive technology, aerospace technology and low-cost AM technologies Provides a broad range of technical questions to ensure comprehensive understanding of the concepts covered

Download or read book Titanium Powder Metallurgy written by Ma Qian and published by Butterworth-Heinemann. This book was released on 2015-02-10 with total page 649 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium Powder Metallurgy contains the most comprehensive and authoritative information for, and understanding of, all key issues of titanium powder metallurgy (Ti PM). It summarizes the past, reviews the present and discusses the future of the science and technology of Ti PM while providing the world titanium community with a unique and comprehensive book covering all important aspects of titanium powder metallurgy, including powder production, powder processing, green shape formation, consolidation, property evaluation, current industrial applications and future developments. It documents the fundamental understanding and technological developments achieved since 1937 and demonstrates why powder metallurgy now offers a cost-effective approach to the near net or net shape fabrication of titanium, titanium alloys and titanium metal matrix composites for a wide variety of industrial applications. - Provides a comprehensive and in-depth treatment of the science, technology and industrial practice of titanium powder metallurgy - Each chapter is delivered by the most knowledgeable expert on the topic, half from industry and half from academia, including several pioneers in the field, representing our current knowledge base of Ti PM. - Includes a critical review of the current key fundamental and technical issues of Ti PM. - Fills a critical knowledge gap in powder metal science and engineering and in the manufacture of titanium metal and alloys

Download or read book Selective Laser Melting Materials and Applications written by Prashanth Konda Gokuldoss and published by . This book was released on 2020 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers, and scientists. AM has the ability to fabricate materials to produce parts with complex shapes without any theoretical restrictions combined with added functionalities. Selective laser melting (SLM), also known as laser-based powder bed processing (LPBF), is one of the main AM process that can be used to fabricate wide variety of materials that are Al-, Ti-, Fe-, Ni-, Co-, W-, Ag-, and Au-based, etc. However, several challenges need to be addressed systematically, such as development of new materials that suit the SLM process conditions so the process capabilities can be fully used to produce new properties in these materials. Other issues in the field are the lack of microstructure-property correlations, premature failure, etc. Accordingly, this Special Issue (book) focuses mainly on the microstructure-correlation in three different alloys: AlSi10Mg, Ti6Al4V, and 304L stainless steel, where six articles are presented. Hence, this Special Issue outlines microstructure-property correlations in the SLM processed materials and provides a value addition to the field of AM.

Download or read book Titanium written by Matthew J. Donachie and published by ASM International. This book was released on 2000 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Designed to support the need of engineering, management, and other professionals for information on titanium by providing an overview of the major topics, this book provides a concise summary of the most useful information required to understand titanium and its alloys. The author provides a review of the significant features of the metallurgy and application of titanium and its alloys. All technical aspects of the use of titanium are covered, with sufficient metals property data for most users. Because of its unique density, corrosion resistance, and relative strength advantages over competing materials such as aluminum, steels, and superalloys, titanium has found a niche in many industries. Much of this use has occurred through military research, and subsequent applications in aircraft, of gas turbine engines, although more recent use features replacement joints, golf clubs, and bicycles.Contents include: A primer on titanium and its alloys, Introduction to selection of titanium alloys, Understanding titanium's metallurgy and mill products, Forging and forming, Castings, Powder metallurgy, Heat treating, Joining technology and practice, Machining, Cleaning and finishing, Structure/processing/property relationships, Corrosion resistance, Advanced alloys and future directions, Appendices: Summary table of titanium alloys, Titanium alloy datasheets, Cross-reference to titanium alloys, Listing of selected specification and standardization organizations, Selected manufacturers, suppliers, services, Corrosion data, Machining data.

Download or read book Additive Manufacturing Volume 2 written by Prashanth Konda Gokuldoss and published by MDPI. This book was released on 2020-04-15 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers and scientists, because of its ability to produce materials with a complex shape without theoretical restrictions and with added functionalities. There are several advantages to employing additive manufacturing as the primary additive manufacturing process. However, there exist several challenges that need to be addressed systematically. A couple such issues are alloy design and process development. Traditionally alloys designed for conventional cast/powder metallurgical processes were fabricated using advanced AM processes. This is the wrong approach considering that the alloys should be coined based on the process characteristics and meta-stable nature of the process. Hence, we must focus on alloy design and development for AM that suits the AM processes. The AM processes, however, improve almost every day, either in terms of processing capabilities or processing conditions. Hence, the processing part warrants a section that is devoted to these advancements and innovations. Accordingly, the present Special Issue (book) focuses on two aspects of alloy development and process innovations. Here, 45 articles are presented covering different AM processes including selective laser melting, electron beam melting, laser cladding, direct metal laser sintering, ultrasonic consolidation, wire arc additive manufacturing, and hybrid manufacturing. I believe that this Special Issue bears is vital to the field of AM and will be a valuable addition.

Download or read book Additive Manufacturing of Titanium Alloys written by Bhaskar Dutta and published by Butterworth-Heinemann. This book was released on 2016-06-17 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive Manufacturing of Titanium Alloys: State of the Art, Challenges and Opportunities provides alternative methods to the conventional approach for the fabrication of the majority of titanium components produced via the cast and wrought technique, a process which involves a considerable amount of expensive machining. In contrast, the Additive Manufacturing (AM) approach allows very close to final part configuration to be directly fabricated minimizing machining cost, while achieving mechanical properties at least at cast and wrought levels. In addition, the book offers the benefit of significant savings through better material utilization for parts with high buy-to-fly ratios (ratio of initial stock mass to final part mass before and after manufacturing). As titanium additive manufacturing has attracted considerable attention from both academicians and technologists, and has already led to many applications in aerospace and terrestrial systems, as well as in the medical industry, this book explores the unique shape making capabilities and attractive mechanical properties which make titanium an ideal material for the additive manufacturing industry. - Includes coverage of the fundamentals of microstructural evolution in titanium alloys - Introduces readers to the various Additive Manufacturing Technologies, such as Powder Bed Fusion (PBF) and Directed Energy Deposition (DED) - Looks at the future of Titanium Additive Manufacturing - Provides a complete review of the science, technology, and applications of Titanium Additive Manufacturing (AM)

Download or read book Titanium Physical Metallurgy Processing and Applications written by F.H. Froes and published by ASM International. This book was released on 2015-02-01 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new book covers all aspects of the history, physical metallurgy, corrosion behavior, cost factors and current and potential uses of titanium. The history of titanium is traced from its early beginnings through the work of Kroll, to the present day broadening market place. Extensive detail on extraction processes is discussed, as well as the various beta to alpha transformations and details of the powder metallurgy techniques.

Download or read book Additive Manufacturing of Metals The Technology Materials Design and Production written by Li Yang and published by Springer. This book was released on 2017-05-11 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a unique guide to the three-dimensional (3D) printing of metals. It covers various aspects of additive, subtractive, and joining processes used to form three-dimensional parts with applications ranging from prototyping to production. Examining a variety of manufacturing technologies and their ability to produce both prototypes and functional production-quality parts, the individual chapters address metal components and discuss some of the important research challenges associated with the use of these technologies. As well as exploring the latest technologies currently under development, the book features unique sections on electron beam melting technology, material lifting, and the importance this science has in the engineering context. Presenting unique real-life case studies from industry, this book is also the first to offer the perspective of engineers who work in the field of aerospace and transportation systems, and who design components and manufacturing networks. Written by the leading experts in this field at universities and in industry, it provides a comprehensive textbook for students and an invaluable guide for practitioners

Download or read book Definition of thermochemical and thermophysical properties to provide a database for the development of new light alloys COST 507 3 Critical evaluation of ternary systems written by Europäische Gemeinschaften and published by . This book was released on 1998 with total page 205 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Laser Additive Manufacturing written by Milan Brandt and published by Woodhead Publishing. This book was released on 2016-09-01 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser Additive Manufacturing: Materials, Design, Technologies, and Applications provides the latest information on this highly efficient method of layer-based manufacturing using metals, plastics, or composite materials. The technology is particularly suitable for the production of complex components with high precision for a range of industries, including aerospace, automotive, and medical engineering. This book provides a comprehensive review of the technology and its range of applications. Part One looks at materials suitable for laser AM processes, with Part Two discussing design strategies for AM. Parts Three and Four review the most widely-used AM technique, powder bed fusion (PBF) and discuss other AM techniques, such as directed energy deposition, sheet lamination, jetting techniques, extrusion techniques, and vat photopolymerization. The final section explores the range of applications of laser AM. Provides a comprehensive one-volume overview of advances in laser additive manufacturing Presents detailed coverage of the latest techniques used for laser additive manufacturing Reviews both established and emerging areas of application

Download or read book Metals for Biomedical Devices written by Mitsuo Niinomi and published by Elsevier. This book was released on 2010-03-31 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: Despite recent advances in medical devices using other materials, metallic implants are still one of the most commercially significant sectors of the industry. Given the widespread use of metals in medical devices, it is vital that the fundamentals and behaviour of this material are understood. Metals in biomedical devices reviews the latest techniques in metal processing methods and the behaviour of this important material.Initial chapters review the current status and selection of metals for biomedical devices. Chapters in part two discuss the mechanical behaviour, degradation and testing of metals with specific chapters on corrosion, wear testing and biocompatibility of biomaterials. Part three covers the processing of metals for biomedical applications with chapters on such topics as forging metals and alloys, surface treatment, coatings and sterilisation. Chapters in the final section discuss clinical applications of metals such as cardiovascular, orthopaedic and new generation biomaterials.With its distinguished editor and team of expert contributors, Metals for biomedical devices is a standard reference for materials scientists, researchers and engineers working in the medical devices industry and academia. - Reviews the latest techniques in metal processing methods including surface treatment and sterilisation - Examines metal selection for biomedical devices considering biocompatibility of various metals - Assesses mechanical behaviour and testing of metals featuring corrosion, fatigue and wear

Download or read book Additive Manufacturing of Metals written by John O. Milewski and published by Springer. This book was released on 2017-06-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This engaging volume presents the exciting new technology of additive manufacturing (AM) of metal objects for a broad audience of academic and industry researchers, manufacturing professionals, undergraduate and graduate students, hobbyists, and artists. Innovative applications ranging from rocket nozzles to custom jewelry to medical implants illustrate a new world of freedom in design and fabrication, creating objects otherwise not possible by conventional means. The author describes the various methods and advanced metals used to create high value components, enabling readers to choose which process is best for them. Of particular interest is how harnessing the power of lasers, electron beams, and electric arcs, as directed by advanced computer models, robots, and 3D printing systems, can create otherwise unattainable objects. A timeline depicting the evolution of metalworking, accelerated by the computer and information age, ties AM metal technology to the rapid evolution of global technology trends. Charts, diagrams, and illustrations complement the text to describe the diverse set of technologies brought together in the AM processing of metal. Extensive listing of terms, definitions, and acronyms provides the reader with a quick reference guide to the language of AM metal processing. The book directs the reader to a wealth of internet sites providing further reading and resources, such as vendors and service providers, to jump start those interested in taking the first steps to establishing AM metal capability on whatever scale. The appendix provides hands-on example exercises for those ready to engage in experiential self-directed learning.

Download or read book Titanium in Medical and Dental Applications written by Francis Froes and published by Woodhead Publishing. This book was released on 2018-05-09 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium in Medical and Dental Applications is an essential reference book for those involved in biomedical materials and advanced metals. Written by well-known experts in the field, it covers a broad array of titanium uses, including implants, instruments, devices, the manufacturing processes used to create them, their properties, corrosion resistance and various fabrication approaches. Biomedical titanium materials are a critically important part of biomaterials, especially in cases where non-metallic biomedical materials are not suited to applications, such as the case of load-bearing implants. The book also covers the use of titanium for implants in the medical and dental fields and reviews the use of titanium for medical instruments and devices. - Provides an understanding of the essential and broad applications of Titanium in both the medical and dental industries - Discusses the pathways to manufacturing titanium into critical biomedical and dental devices - Includes insights into further applications within the industry