Download or read book Tensile Fatigue and Creep Properties of Forged Aluminum Alloys at Temperatures Up to 800 Degrees F written by L. R. Jackson and published by . This book was released on 1948 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents data on the tensile strength, fatigue strength, creep properties, and thermal expansion of forged aluminum alloys XB18S, 18S, 24S, and 32S, which are pertinent to the application of these alloys in the temperature range from 70 to 800 degrees F. The report also contains a critical discussion of the data and their application to design of aircraft engines.
Download or read book Tensile Fatigue and Creep Properties of Forged Aluminum Alloys at Temperatures Up to 800 Deg F written by and published by . This book was released on 1948 with total page 49 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper presents data on the tensile strength, fatigue strength, creep properties, and thermal expansion of forged aluminum alloys XBl8S, 185, 24S, and 325, which are pertinent to the application of these alloys in the temperature range from 700 to 8Q%O F. Included arc data taken from published sources, unpublished material made available through the courtesy of the Aluminum Company of America and the National Bureau of Standards, and original data, obtained at Battelle Memorial Institute, which extend this previous information. The work also contains a critical discussion of the data and their application to design of aircraft engine.
Download or read book Tensile Fatigue and Creep Properties of Forged Aluminum Alloys at Temperatures Up to 800 F written by L. R. Jackson and published by . This book was released on 1948 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Properties of Aluminum Alloys written by John Gilbert Kaufman and published by ASM International. This book was released on 1999-01-01 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compilation of data collected and maintained for many years as the property of a large aluminum company, which decided in 1997 to make it available to other engineers and materials specialists. In tabular form, presents data on the tensile and creep properties of eight species of wrought alloys and five species of cast alloys in the various shapes used in applications. Then looks at the fatigue data for several alloys under a range of conditions and loads. The data represent the typical or average findings, and though some were developed years ago, the collection is the largest and most detailed available. There is no index.
Download or read book Properties of Aluminum Alloys written by John Gilbert Kaufman and published by ASM International. This book was released on 2008-01-01 with total page 569 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compilation of data collected and maintained for many years as the property of a large aluminum company, which decided in 1997 to make it available to other engineers and materials specialists. In tabular form, presents data on the tensile and creep properties of eight species of wrought alloys and five species of cast alloys in the various shapes used in applications. Then looks at the fatigue data for several alloys under a range of conditions and loads. The data represent the typical or average findings, and though some were developed years ago, the collection is the largest and most detailed available. There is no index.
Download or read book Aluminum and Aluminum Alloys written by and published by . This book was released on 1966 with total page 118 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tensile Properties and Creep Strength of Three Aluminum Alloys Exposed Up to 25 000 Hours at 200 to 400 F 370 to 480 K written by Dick M. Royster and published by . This book was released on 1969 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Investigation of the Effects of Rapid Loading and Elevated Temperatures on the Mechanical Properties of Compressive and Column Members written by P. R. Dioguardo and published by . This book was released on 1962 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: Short time tensile and compressive properties were evaluated for Rene' 41 and Haynes 25 sheet alloys at room temperature and 800 to 2200 F. Tests conducted at various strain rates (0.00001 to 0.1 in./in.sec) produced significant differences in strength, particularly at elevated temperatures. Creep properties, both tensile and compressive, were determined for the same alloys at temperatures of 1600 to 2200 F and times up to 15 minutes. At the higher stress levels, creep rates became very rapid and considerable amounts of plastic strain occurred in times of 1 sec or less. A preliminary study was conducted on the use of programmed, forced strain rate tests to predict short time creep properties.
Download or read book Technical Note National Advisory Committee for Aeronautics written by United States. National Advisory Committee for Aeronautics and published by . This book was released on 1948 with total page 1136 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Room Temperature Tensile Properties of Large 7075 T6 and 7075 T73 Aluminum alloy Forgings written by D. P. Moon and published by . This book was released on 1970 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: Room-temperature tensile properties were determined for large 7075-T6 and 7075-T73 aluminum-alloy forgings. Forging sizes ranged from about 1.5 to 15 inches (short-transverse direction) for production forgings and up to 20 inches for step forgings. Heat-treated thickness was 0.75 to 1.000 inch for the T6 temper but ranged up to 10 inches for the T73 temper. Regression coefficients and standard d deviations are presented for three properties (TUS, TYS, and elongation) in each of three test directions. In addition, average values and two statistical minima are tabulated for each property and test direction at each of several discrete sizes, and a comparison is made with the corresponding requirements of Specification MIL-A-22771C(ASG). (Author).
Download or read book Correlation of Literature on the Effect of Testing Temperature on the Mechanical Properties of Wrought Aluminum Base Alloys written by Helen R. Pritchard and published by . This book was released on 1955 with total page 124 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Properties of Magnesium Alloy Forgings written by Evan Henry Schuette and published by . This book was released on 1960 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Ordnance Corps Pamphlet written by and published by . This book was released on 1956 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tensile Properties and Sheet bending Fatigue Properties of Some Refractory Metals at Room Temperature written by Lee R. Foster and published by . This book was released on 1963 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results of tensile stress-strain tests and completely reversed sheet-bending fatigue tests conducted at room temperature on unnotched sheet specimens of Ta-lOW tantalum alloy, D-3l niobium alloy, pure tungsten, and Mo-0.5Ti molybdenum alloy are presented. Fatigue data from tests on similar specimens of 2024-T3 aluminum alloy and 17-7 PH stainless steel are compared with previous data from axial-load tests on larger specimens of these materials to determine whether the small size of the specimens used in this investigation produces representative results. Comparisons of the various materials on the basis of applied-stress- ultimate-strength and strength-density ratio also are presented.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1987 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1962 with total page 1116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tensile Properties and Creep Strength of Three Aluminum Alloys Exposed Up to 25 000 Hours at 200 Degrees to 400 Degrees F 370 Degrees to 480 Degrees K written by United States. National Aeronautics and Space Administration and published by . This book was released on 1969 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
