Download or read book Study of Mixing and Combustion Modeling for Diesel Engine Using LES written by Ting Liang and published by . This book was released on 2010 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.
Download or read book Engine Modeling and Simulation written by Avinash Kumar Agarwal and published by Springer Nature. This book was released on 2021-12-16 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the simulation and modeling of internal combustion engines. The contents include various aspects of diesel and gasoline engine modeling and simulation such as spray, combustion, ignition, in-cylinder phenomena, emissions, exhaust heat recovery. It also explored engine models and analysis of cylinder bore piston stresses and temperature effects. This book includes recent literature and focuses on current modeling and simulation trends for internal combustion engines. Readers will gain knowledge about engine process simulation and modeling, helpful for the development of efficient and emission-free engines. A few chapters highlight the review of state-of-the-art models for spray, combustion, and emissions, focusing on the theory, models, and their applications from an engine point of view. This volume would be of interest to professionals, post-graduate students involved in alternative fuels, IC engines, engine modeling and simulation, and environmental research.
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on 2022-01-21 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprehensively discusses diesel combustion phenomena like ignition delay, fuel-air mixing, rate of heat release, and emissions of smoke, particulate and nitric oxide. It enables quantitative evaluation of these important phenomena and parameters. Most importantly, it attempts to model them with constants that are independent of engine types and hence they could be applied by the engineers and researchers for a general engine. This book emphasizes the importance of the spray at the wall in precisely describing the heat release and emissions for most of the engines on and off-road. It gives models for heat release and emissions. Every model is thoroughly validated by detailed experiments using a broad range of engines. The book describes an elegant quasi-one-dimensional model for heat release in diesel engines with single as well as multiple injections. The book describes how the two aspects, namely, fuel injection rate and the diameter of the combustion bowl in the piston, have enabled meeting advanced emission, noise, and performance standards. The book also discusses the topics of computational fluid dynamics encompassing RANS and LES models of turbulence. Given the contents, this book will be useful for students, researchers and professionals working in the area of vehicle engineering and engine technology. This book will also be a good professional book for practising engineers in the field of combustion engines and automotive engineering.
Download or read book LES Scalar Mixing and Combustion Modeling in Internal Combustion Engines written by Yuxin Zhang and published by . This book was released on 2011 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Development of a Partially Premixed Combustion Model for a Diesel Engine Using Multiple Injection Strategies written by Rene Thygesen and published by Logos Verlag Berlin GmbH. This book was released on 2012 with total page 157 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to fulfil future emissions legislations, new combustion systems are to be investigated. One way of improving exhaust emissions is the application of multiple injection strategies and conventional or partially premixed combustion conditions to a Diesel engine. The application of numerical techniques as CFD supports and improves the quality of engine developments. Unfortunately, current spray and combustion models are not accurate enough to simulate multiple injection systems, being in this way a topic of research. The goal of this study was the development of a novel simulation method for the investigation of Diesel engines operated with multiple injection strategies and different combustion modes. The first part of this work focused in improving the spray modelling. The inform ation of 3D CFD simulations of the injector nozzle was introduced in the spray simulation as boundary conditions developing coupling subroutines for this issue. The atomisation modelling was also improved using validated presumed droplet size distributions. Moreover, to avoid the simulation of the injector nozzle for every investigated operating point, a novel interpolating tool was developed in order to create spray boundary conditions based on few 3D CFD simulations of the nozzle under certain initial and boundary conditions. The second part of this thesis dealt with the combustion modelling of Diesel engines. For this issue, a laminar flamelet approach called Representative Interactive Flamelet model (RIF) was selected and implemented. Afterwards, an extended combustion model based on RIF was developed in order to take into account multiple injection strategies. Finally, this new model was validated with a wide range of operating points: applying multiple injection strategies under conventional and partially premixed combustion conditions.
Download or read book Modeling Engine Spray and Combustion Processes written by Gunnar Stiesch and published by Springer Science & Business Media. This book was released on 2003-04-10 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Download or read book Using Large Eddy Simulations to Study Diesel DI HCCI Engine Flow Structure Mixing and Combustion written by Rahul Jhavar and published by . This book was released on 2007 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Optimization Methods for the Mixture Formation and Combustion Process in Diesel Engines written by Jost Weber and published by Cuvillier Verlag. This book was released on 2008 with total page 265 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Simulation of the Diesel Engine Combustion Process Using the Stochastic Reactor Model written by Michal Pasternak and published by Logos Verlag Berlin. This book was released on 2016 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present work is concerned with the simulation of combustion, emission formation and fuel effects in Diesel engines. The simulation process is built around a zero-dimensional (0D) direct injection stochastic reactor model (DI-SRM), which is based on a probability density function (PDF) approach. An emphasis is put on the modelling of mixing time to improve the representation of turbulence-chemistry interactions in the 0D DI-SRM. The mixing time model describes the intensity of mixing in the gas-phase for scalars such as enthalpy and species mass fraction. On a crank angle basis, it governs the composition of the gas mixture that is described by PDF distributions for the scalars. The derivation of the mixing time is based on an extended heat release analysis that has been fully automated using a genetic algorithm. The predictive nature of simulations is achieved through the parametrisation of the mixing time model with known engine operating parameters such as speed, load and fuel injection strategy. It is shown that crank angle dependency of the mixing time improves the modelling of local inhomogeneity in the gas-phase for species mass fraction and temperature. In combination with an exact treatment of the non-linearity of reaction kinetics, it enables an accurate prediction of the rate of heat release, in-cylinder pressure and exhaust emissions, such as nitrogen oxides, unburned hydrocarbons and soot, from differently composed fuels. The method developed is particularly tailored for computationally efficient applications that focus on the details of reaction kinetics and the locality of combustion and emission formation in Diesel engines.
Download or read book Diesel Engine Modeling written by Society of Automotive Engineers and published by SAE International. This book was released on 1999 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Practical Diesel engine Combustion Analysis written by Bertrand D. Hsu and published by SAE International. This book was released on 2002 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: The diesel engine is one of the most efficient types of heat engines and is widely used as a prime mover for many applications. In recent years, with the aid of modern computers, engine combustion modeling has made great progress. However, due to the complexities of the processes involved in the practical diesel engine, there are still too many unknowns preventing computational prediction to have the accuracy level required by industry. This book examines some basic characteristics of diesel engine combustion process, and describes the commonly used tool to analyze combustion - heat release analysis. It addition, Practical Diesel-Engine Combustion Analysis describes the performance changes that might be encountered in the engine user environment, with a goal of helping the reader analyze his own practical combustion problems. Chapters include: Combustion and Fuel-Injection Processes in the Diesel Engine Heat Release and its Effect on Engine Performance Alternate Fuels Combustion Analysis
Download or read book Simulation and Optimization of Internal Combustion Engines written by Zhiyu Han and published by SAE International. This book was released on 2021-12-28 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Simulation and Optimization of Internal Combustion Engines provides the fundamentals and up-to-date progress in multidimensional simulation and optimization of internal combustion engines. While it is impossible to include all the models in a single book, this book intends to introduce the pioneer and/or the often-used models and the physics behind them providing readers with ready-to-use knowledge. Key issues, useful modeling methodology and techniques, as well as instructive results, are discussed through examples. Readers will understand the fundamentals of these examples and be inspired to explore new ideas and means for better solutions in their studies and work. Topics include combustion basis of IC engines, mathematical descriptions of reactive flow with sprays, engine in-cylinder turbulence, fuel sprays, combustions and pollutant emissions, optimization of direct-injection gasoline engines, and optimization of diesel and alternative fuel engines.
Download or read book Combustion Modeling for Diesel Engine Control Design written by Christian Felsch and published by . This book was released on 2009 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Studies of Diesel Engine Combustion Using a Multidimensional Computer Simulation written by Constantine A. Varnavas and published by . This book was released on 1990 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced technologies in flow dynamics and combustion in propulsion and power volume II written by Lei Luo and published by Frontiers Media SA. This book was released on 2023-02-09 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Quasi dimensional Charge Motion and Turbulence Model for Combustion and Emissions Prediction in Diesel Engines with a fully Variable Valve Train written by Qirui Yang and published by Springer Nature. This book was released on 2021-10-01 with total page 141 pages. Available in PDF, EPUB and Kindle. Book excerpt: Qirui Yang develops a model chain for the simulation of combustion and emissions of diesel engine with fully variable valve train (VVT) based on extensive 3D-CFD simulations, and experimental measurements on the engine test bench. The focus of the work is the development of a quasi-dimensional (QDM) flow model, which sets up a series of sub-models to describe phenomenologically the swirl, squish and axial charge motions as well as the shear-related turbulence production and dissipation. The QDM flow model is coupled with a QDM combustion model and a nitrogen oxides (NOx) / soot emission model. With the established model chain, VVT operating strategies of diesel engine can be developed and optimized as part of the simulation for specific engine performance parameters and the lowest NOx and soot emissions.
