Download or read book Sound Measurement Off Road Self Propelled Work Machines Operator Work Cycle written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: Crawler LoaderWheel LoaderDumperTractor ScraperGraderCrawler Tractor with DozerWheel Tractor with DozerPad Foot Wheel Compactor with DozerBackhoeHydraulic ExcavatorLog SkidderExcavator and Wheel Feller-BuncherPipelayerRoller/CompactorTrencherSweeper The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.

Download or read book Sound Measurement Off Road Self Propelled Work Machines Operator Work Cycle written by OPTC3, Lighting and Sound Committee and published by . This book was released on 2008 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: Crawler LoaderWheel LoaderDumperTractor ScraperGraderCrawler Tractor with DozerWheel Tractor with DozerPad Foot Wheel Compactor with DozerBackhoeHydraulic ExcavatorLog SkidderExcavator and Wheel Feller-BuncherPipelayerRoller/CompactorTrencherSweeper The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.

Download or read book Sound MeasurementOff Road Self Propelled Work Machines Operator Work Cycle written by OPTC3, Lighting and Sound Committee and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: Crawler Loader Grader Log Skidder Wheel Loader Crawler Tractor with Dozer Pipelayer Dumper Wheel Tractor with Dozer Trencher Tractor Scraper Backhoe Sweeper Roller/Compactor Hydraulic Excavator Pad Foot Wheel Compactor with Dozer Excavator and Wheel Feller-Buncher The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle representing continuous medium to heavy work. The work cycles provide a repeatable reproduceable means to uniformly measure working machines against a "yard stick. A method to relate the time weighted average sound level at the operator station(s) to estimate operator sound exposure with part load work, supervision, and rest breaks is also provided. SAE J1166 has been reaffirmed to comply with the SAE Five-Year Review policy.

Download or read book Sound Measurement Off Road Work Machines Operator Singular Type written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1986 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard describes the instrumentation and procedures to be used in measuring sound levels at the operator station for self-propelled sweepers as defined in SAE J2130 and self-propelled off-road work machines in categories 1, 2, 4, and 5, of SAE J1116. This SAE document is applicable to machines that have operator stations where the operator can either stand or sit and will be either transported by, or walk with the machine during its operation. The sound levels obtained using this procedure are repeatable and representative of the higher range of sound levels generated by machines under actual field operating conditions. Due to variability of field operating conditions, this data is not intended to be used for operator noise exposure evaluations. Measurement and calculation of the operator's sound exposure should follow SAE J1116.

Download or read book Department Of Defense Index of Specifications and Standards Numerical Listing Part II September 2005 written by and published by DIANE Publishing. This book was released on with total page 798 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sound Measurement Off Road Work Machines Operator Singular Type written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1995 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard describes the instrumentation and procedures to be used in measuring sound levels at the operator station for self-propelled sweepers as defined in SAE J2130 and self-propelled off-road work machines in categories 1, 2, 4, and 5, of SAE J1116. This SAE document is applicable to machines that have operator stations where the operator can either stand or sit and will be either transported by, or walk with the machine during its operation. The sound levels obtained using this procedure are repeatable and representative of the higher range of sound levels generated by machines under actual field operating conditions. Due to variability of field operating conditions, this data is not intended to be used for operator noise exposure evaluations. Measurement and calculation of the operator's sound exposure should follow SAE J1116.

Download or read book Index of Specifications and Standards written by and published by . This book was released on 2005 with total page 810 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sound Measurement Off Road Work Machines Exterior written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1995 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the instrumentation and procedure to be used in measuring the exterior sound levels for self-propelled sweepers as defined in SAE J2130 and self-propelled off-road work machines in categories 1,2,4, and 5 of SAE J1116. This document does not address the operation of safety devices such as backup alarms, horns, or accessories. The sound levels obtained by using the test procedures set forth in this document are repeatable and are representative of the higher range of sound levels generated by machines under actual field operating conditions. Due to variability of field operating conditions, this data is not intended to be used for construction site boundary noise evaluations.

Download or read book Sound Measurement Off Road Work Machines Exterior written by OPTC3, Lighting and Sound Committee and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the instrumentation and procedure to be used in measuring the exterior sound pressure levels for self-propelled off-road work machines as defined in sections 1, 3, 5 and 6 of SAE J1116. This document does not address the operation of safety devices such as backup alarms, horns, or accessories. The sound levels obtained by using the test procedures set forth in this document are repeatable and are representative of the higher range of sound levels generated by machines under actual field operating conditions. Due to the variability of field operating conditions, this data is not intended to be used for construction site boundary noise evaluations. The test method defined within SAE J88 has been developed and used for nearly than 40 years. The last update to SAE J88 was in 2006 which updated references to align with modern standards. With no changes in the test method or references, SAE J88 should be stabilized.

Download or read book Department Of Defense Index of Specifications and Standards Federal Supply Class Listing FSC Part III November 2005 written by and published by DIANE Publishing. This book was released on with total page 773 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book S A E Handbook written by and published by . This book was released on 1991 with total page 1034 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sound Measurement Self Propelled Agricultural Equipment Exterior written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1987 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the instrumentation and procedures to be used in measuring exterior sound levels of self-propelled agricultural field equipment of 15 kW (20 net engine hp) or greater. It is not intended to cover operation of safety devices (such as alarms), or equipment used primarily in stationary operation. The sound levels obtained by using this test procedure are repeatable and representative of the higher range of sound levels generated by the machine in normal road transport. The sound levels are not intended to represent the average or equivalent sound levels over a field use cycle.

Download or read book Acoustics Measurement of Noise Emitted By Earthmoving Machinery At the OperatorS Position Simulated Work Cycle Test Conditions written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1991 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard describes a method for determining the noise emitted by earthmoving machinery at the operator's position in terms of the equivalent continuous A-weighted sound pressure level while the machine is carrying out a simulated work cycle. This SAE standard is a special test code for specific types of earthmoving machinery. It is an extension of ISO 6081 which contains the general requirements for many types of machinery and equipment. A simulated rather than an actual work cycle test condition is chosen. Simulated work cycles provide acceptable noise emission data which are repeatable and representative. Actual work cycle tests are complex and repeatability can be a problem. Specific procedures are described in this document to enable the sound pressure level at the operator's position,with the machine in a simulated work cycle test condition, to be determined in a manner which is repeatable. Attachments (bucket, dozer, etc.) for the manufacturer's production version are to be fitted since this is the configuration most likely to exist when the machine is in actual use. This document enables compliance with noise limits to be determined. It can also be used for evaluation purposes in noise reduction investigations. An additional special test code is given in SAE J2104/ISO 6395. This other special test code is intended to be used to determine the noise emitted by earthmovign machinery in terms fo the A-weighted sound power level while the machine is in a simulated work cycle test condition. Corresponding measurements of exterior noise and noise at the operator's position under stationary test conditions are described in SAE J2102/ISO 6393 and ISO J2103/ISO 6394, respectively.

Download or read book OPERATOR STATION SOUND LEVEL MEASUREMENT PROCEDURE FOR POWERED MOBILE EARTHMOVING MACHINERYWORK CYCLE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1976 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the procedures to be used only in measuring sound levels and the determination of the time weighted average sound level at the operator station(s) of powered mobile earthmoving machinery of 15 kW (20 bhp) and over. This Recommended Practice is applicable to earthmoving machinery which has operator station(s) where the operator can either stand or sit and is transported by the machinery during its operation. The Recommended Practice describes the instrumentation requirements and specifies work cycles for earthmoving machinery. The Recommended Practice describes the method used to calculate the time weighted average sound level at the operator station(s)identified in this practice as Leq(5)for continuous operation on the work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.

Download or read book Department Of Defense Index of Specifications and Standards Alphabetical Listing Part I July 2005 written by and published by DIANE Publishing. This book was released on with total page 779 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sound Measurement Trenching Machines written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1999 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard specifies procedures for measuring operator and exterior sound levels emitted by self-powered trenching machines regardless of engine size. This procedure does not cover operation of devices such as backup alarms, horns, or accessories such as paving breakers. The sound levels obtained using this procedure are repeatable and representative of the higher range of sound levels generated by machines under actual field operating conditions, but do not necessarily represent the average sound level over a field use cycle. Measurement and calculation of the operator's sound exposure should follow SAE J1166.

Download or read book OPERATOR STATION SOUND LEVEL MEASUREMENT PROCEDURE FOR EARTHMOVING MACHINERYWORK CYCLE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1979 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the procedures to be used only in measuring sound levels and the determination of the time weighted sound level at the operator station(s) of earthmoving machinery of 15 kW (20 bhp) and over. Earthmoving machinery is defined per SAE J1057a. This recommended practice is applicable to earthmoving machinery which has operator station(s) where the operator can either stand or sit and is transported by the machinery during operation. The recommended practice describes the instrumentation requirements and specifies work cycles for earthmoving machinery. The recommended practice describes the method used to calculate the time weighted average sound level at the operator station(s) identified in the practice as Leq(5) for continuous operation of the work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.