Download or read book Sol Gel Derived Titania Films And Their Potential Application As Gas Sensor written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Today there is a great deal of interest in the development of gas sensors for various applications like monitoring of toxic gases, detection in oil reservoirs, mines, homes etc. Solid-state gas sensors have many advantages over the conventional analytical methods and hence are widely used. Amongst them, semiconducting metal-oxides based sensors are popular due to many advantages like low cost, small size, high sensitivity and long life. The present thesis reports a detailed work of TiO2 (Titania) thin film fabrication based on sol-gel method, study of their crystallization behavior and surface morphology, and characterizing them for alcohol sensing properties Sol-gel method is a wet chemical technique with many advantages over the conventional methods and offers a high degree of versatility to modify the film properties. Titania thin films were made with titanium isopropoxide as the precursor and ethanol and isopropanol as the solvents. Also effect of surfactants(PEG and CTAB) on the sol properties and film properties have experimentally examined. A in-house gas sensor testing setup has been designed and fabricated to characterize the sensors. Sensors with three different electrode configurations and also two different electrode material have been tested. The electrode geometry and material play a significant role on the sensing behavior and results for the same have been discussed.
Download or read book Sol Gel Derived Optical and Photonic Materials written by Rui Almeida and published by Woodhead Publishing. This book was released on 2020-12-14 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sol-gel processing is a low temperature, low cost wet chemistry route to a range of different materials, particularly glassy and ceramic oxides, including nanoparticles and powders, fibers, thin films and membranes, or monoliths and composites. Thin films and coatings represent by far the most important category of sol-gel derived products with optical, electronic and magnetic functionalities, for example photoresist and dielectric spin-on-glass layers, flat screen displays, anti-reflection, conducting and magnetic disk coatings, as well as photochromic, electrochromic and photovoltaic coatings. Sol-gel derived materials are homogeneous at the molecular level and are a good example of a bottom-up approach to materials synthesis. There is increasing need of new optical and photonic materials with improved performance, where molecular level homogeneity and easy fabrication in film form may be especially convenient, highlighting a decisive advantage of sol-gel over other more established technologies to obtain graded index optical components, solar control coatings, phosphors, glass ceramics or multilayer photonic structures. There is no book available yet which focuses in particular on optical and photonic sol-gel derived materials. This is what makes this book unique at this point for those especially or exclusively interested in optical and photonic functional materials and applications. This book represents an important tool to update scientists and engineers with recent advances in the rapidly evolving field of optical and photonic materials, components and devices. Our target audience are those working in materials science, physics, engineering and chemistry disciplines, in particular academics and researchers working in advanced optical/photonic processing technologies, research and development engineers in high technology industries and research project leaders. This book will also be an essential tool for graduate students pursuing a PhD or even a Master's degree. Reviews wide range of sol-gel derived coatings including reflective and anti-reflective, self-cleaning, and electrochromic Discusses latest advances in sol-gel derived photonic crystals including one dimensional, two dimensional, and three dimensional structures Addresses key applications in solid state lighting, solar cells, sensors, fiber optics, and magneto-optical devices
Download or read book Preparation and Characterization of Sol gel Derived Titania silica Thin Films written by Young-Min Kwon and published by . This book was released on 1996 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sol gel Derived Titania Based Ceramic Thin Films for Implant Coatings written by Sami Areva and published by . This book was released on 2006 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sol gel Derived Metal Oxide Thin Films Design of New Materials for Chemical Sensing written by Kathryn Graessley Severin and published by . This book was released on 1996 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Structuring and filling of titania films for applications in photovoltaics written by Monika Rawolle and published by Cuvillier Verlag. This book was released on 2013-04-02 with total page 334 pages. Available in PDF, EPUB and Kindle. Book excerpt: Kurzbeschreibung Die Möglichkeiten, Titandioxid Nanostrukturen zu synthetisieren, sowie die erhaltenen Strukturen rückzubefüllen, werden mit Hinblick auf Anwendungen in der Photovoltaik in der vorliegenden Arbeit untersucht. Auf Titandioxid basierende Solarzellen werden in Hybridsolarzellen und in Farbstoffsolarzellen unterteilt. Das Hauptaugenmerk der Untersuchungen liegt auf der Korrelation zwischen Morphologie und Funktion der resultierenden Strukturen. Die verschiedenen untersuchten Systeme und die damit verbundenen Fragestellungen umfassen zum einen die Strukturierung von Titandioxid und zum anderen das Rückbefüllen dieser Strukturen. Die Synthese von Titandioxid wird mittels Sol-Gel Chemie vorgenommen. Die Strukturen werden in der Synthese durch Blockcopolymertemplate vorgegeben. Die damit hergestellten dünnen Filme von Titandioxid zeigen eine hohe Porosität, mit einer Schwammartigen Morphologie die sowohl Mesoporen als auch Makroporen aufweist. Die Strukturen werden in dünnen Filmen und in einem nanostrukturierten Tropfen untersucht. Eine Verbesserung der Strukturen durch die Kombination der Sol-Gel Synthese mit Mikrofluidik wird ebenfalls diskutiert. Zudem wird eine mögliche Syntheseroute bei niedrigen Temperaturen vorgestellt, die es erlaubt kristallines Titandioxid zu erhalten. Die Stabilität der Strukturen gegen die Kapillarkräfte bei der Infiltrierung von Wasserdampf wird getestet. Um funktionierende Solarzellen zu erhalten, müssen die Titandioxidnanostrukturen mit einem lochleitenden Material gefüllt werden. Der Grad der Rückbefüllung mit lochleitenden Materialien korreliert mit der Funktion in Solarzellen. Description In the presented thesis, the possibilities to synthesize titania nanostructures and the possibilities to fill the resulting nanostructures by other materials are investigated for photovoltaic applications. The solar cells based on titania are distinguished either as hybrid or as dye-sensitized solar cells. The main focus of the investigations lies on the correlation of the morphology and the functionality of the obtained thin films. The different investigated systems and related questions comprise the structuring of titania on the one hand, and the filling of the structures on the other hand. Sol-gel chemistry in combination with block copolymers as structure templates is applied to obtain titania thin films with a sponge-like morphology, which shows a high porosity and both mesopores and macropores. The structures are investigated in thin films, but also in a nanostructured drop of titania. Improvement of the structures by the combination of micro-fluidics with the templated sol-gel is also discussed. Furthermore, a low temperature synthesis route is examined to obtain crystalline titania. The stability of the resulting titania films is checked for water vapor infiltration with the resulting capillary forces. In order to obtain working solar cells, the titania nanostructures need to be filled by hole-conducting materials. The degree of filling of the structures with hole-conducting organic materials is related to the functionality of the solar cells.
Download or read book Sol Gel Materials written by John D. Wright and published by CRC Press. This book was released on 2018-10-03 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sol-Gel processing methods, first used historically for decorative and constructional materials, were extensively developed in the last century for applications such as glasses, ceramics, catalysts, coatings, composites and fibres. Today they are reaching their full potential, enabling the preparation of new generations of advanced materials not easily accessible by other methods yet using mild, low-energy conditions. The topic is therefore increasingly included in advanced undergraduate, MSc and PhD programmes in the areas of chemistry, physics and materials science. This concise introductory text, written at the advanced undergraduate/first-year postgraduate level, is also suitable as an introduction to the development, mechanisms, chemistry, characterisation methods and applications of the technique. It provides readers with an extensive yet concise grounding in the theory of each area of the subject and details the real and potential applications and the future prospects of sol-gel chemistry.
Download or read book Functional Oxide Based Thin Film Materials written by Dong-Sing Wuu and published by MDPI. This book was released on 2020-05-29 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue on Functional Oxide-Based Thin-Film Materials touches on the latest advancements in several aspects related to material science: the synthesis of novel oxide, photoluminescence characteristics, photocatalytic ability, energy storage, light emitter studies, low-emissivity glass coatings, and investigations of both nanostructure and thin-film properties. It represents an amalgamation of specialists working with device applications and shedding light on the properties and behavior of thin-film oxides (e.g., GaOx, Ga2O3, HfO2, LiNbO3, and doped ZnO, among numerous others). The papers cover many aspects of thin-film science and technology, from thin film to nanostructure and from material properties to optoelectronic applications, thus reflecting the many interests of the community of scientists active in the field.
Download or read book Aqueous Sol Gel Derived Titania and Modified Titania for Biomedical Applications written by Francis James Allison and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Preparation and Characterization of Sol gel Derived Peroxo Titania and Its Application for Nano crystalline Dye Sensitized Solar Cell written by Young Jun Hong and published by . This book was released on 2002 with total page 554 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sol Gel Technology for Thin Films Fibers Preforms Electronics and Specialty Shapes written by Lisa C. Klein and published by William Andrew. This book was released on 1988 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Provides background and fundamentals and evaluates present technology. Main topics are thin films in optical, mechanical, and electrical applications; fibers in refractories, composite reinforcement, and thermal insulation; and special applications such as preforms, microballoons, and electronics. Articles are grouped under chemistry and phase transformations; coatings, thin films, and surface treatment; continuous, discontinuous, and woven fibers; monoliths, shapes, and preforms; and special applications. Annotation(c) 2003 Book News, Inc., Portland, OR (booknews.com)
Download or read book Sol Gel Nanocomposites written by Massimo Guglielmi and published by Springer. This book was released on 2016-09-03 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides comprehensive coverage of nanocomposite materials obtained by the sol-gel method, from synthesis to applications and including design tools for combining different properties. Sol-gel nanocomposites are of great interest in meeting processing and application requirements for the development of multifunctional materials. These materials are already commercialized for a number of applications from scratch-resistant and anti-adhesive coatings to optical materials with active and passive properties. Biomedical applications, holographic recordings, fuel cells and hydrogen storage, resists and catalysts are among the potential uses. The novel mechanical, optical and electronic properties of nanocomposite materials depend not only on the individual component materials, but also on their morphology and nanoscale interfacial characteristics. Sol-gel is a highly versatile method for obtaining both the matrix and the filler of the nanocomposite and for chemically adjusting the interface to optimize structure and properties. Although nanocomposites are widely discussed in the literature, the focus has been mainly on polymer nanocomposites. This book addresses nanocomposites based on inorganic or hybrid organic-inorganic matrices, with an emphasis on the scientific principles which are the basis for nanocomposite sol-gel synthesis and applications. A didactic approach is followed, with different topics developed from a fundamental point of view together with key examples and case studies. First comprehensive treatment of nanocomposites obtained by sol-gel methods Focuses on nanocomposites with inorganic and hybrid organic-inorganic matrices Describes design tools to optimize structure and properties for various applications Covers synthesis, processing, characterization, and modeling Uses first principles to describe the influence of interfacial characteristics on materials properties Presents case studies for both films and bulk applications Provides examples of products on the market, with descriptions of the scientific principles at the base of their success Includes contributions from recognized leaders in this multidisciplinary area.
Download or read book Sol Gel Processing and Applications written by Y.A. Attia and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: During my professional career, I developed a strong interest in sol-gel technology, and worked on both xerogel and aerogel systems. My fascination with aerogels has driven me to explore their commercial potential, which is currently an important component of my company's business plan. Together with my co-workers, I have also worked on the preparation of controlled PZT and silica xerogels as well as thin film coatings of metals by the sol-gel technology, These experiences convinced me of the tremendous potentials of this technology. A conviction that is shared by many scientists, engineers, and business leaders around the globe. Many sol-gel derived products are already articles of commerce. However, to expand the commercial potential of sol-gel technology, two challenges must be met: (1) the quality of sol-gel derived products must continue to meet or exceed the quality of competing products, (2) the production cost of sol-gel products (specially aerogels) must continued to decline. A key to lowering the costs of sol-gel products is finding inexpensive precursors.
Download or read book TiO2 Nanoparticles written by Aiguo Wu and published by John Wiley & Sons. This book was released on 2020-06-02 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: A unique book that summarizes the properties, toxicology, and biomedical applications of TiO2-based nanoparticles Nanotechnology is becoming increasingly important for products used in our daily lives. Nanometer-sized titanium dioxide (TiO2) are widely used in industry for different purposes, such as painting, sunscreen, printing, cosmetics, biomedicine, and so on. This book summarizes the advances of TiO2 based nanobiotechnology and nanomedicine, covering materials properties, toxicological research, and biomedical application, such as antibacter, biosensing, and cancer theranostics. It uniquely integrates the TiO2 applications from physical properties, toxicology to various biomedical applications, and includes black TiO2 based cancer theranostics. Beginning with a comprehensive introduction to the properties and applications of nanoparticles, TiO2 Nanoparticles: Applications in Nanobiotechnology, Theranostics and Nanomedicine offers chapters on: Toxicity of TiO2 Nanoparticles; Antibacterial Applications of TiO2 Nanoparticles; Surface Enhanced Raman Spectrum of TiO2 Nanoparticle for Biosensing (TiO2 Nanoparticle Served as SERS Sensing Substrate); TiO2 as Inorganic Photosensitizer for Photodynamic Therapy; Cancer Theranostics of Black TiO2 Nanoparticles; and Neurodegenerative Disease Diagnostics and Therapy of TiO2-Based Nanoparticles. This title: -Blends the physical properties, toxicology of TiO2 nanoparticles to the many biomedical applications -Includes black TiO2 based cancer theranostics in its coverage -Appeals to a broad audience of researchers in academia and industry working on nanomaterials-based biosensing, drug delivery, nanomedicine TiO2 Nanoparticles: Applications in Nanobiotechnology, Theranostics and Nanomedicine is an ideal book for medicinal chemists, analytical chemists, biochemists, materials scientists, toxicologists, and those in the pharmaceutical industry.
Download or read book Synthesis and Characterization of Sol gel Derived Tantalum Oxide Tantalum Nitride and Nickel alumina Thin Films written by Gerald Thomas Kraus and published by . This book was released on 1997 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Synthesis and Characterization of Titania based Thin Films for Sensor Applications written by Benjamin Elden Wilson and published by . This book was released on 2005 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Attempts to develop various methods for producing TiO2(titanium oxide) thin films using pulsed laser deposition and sol-gel synthesis. Characterizes the thin films using SEM (scanning electron microscope) and XRD (x-ray diffraction). Models photocatalysis kinetic data acquired from a previous experiment done by Young et al.
Download or read book Chemical Solution Deposition of Functional Oxide Thin Films written by Theodor Schneller and published by Springer Science & Business Media. This book was released on 2014-01-24 with total page 801 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the first text to cover all aspects of solution processed functional oxide thin-films. Chemical Solution Deposition (CSD) comprises all solution based thin- film deposition techniques, which involve chemical reactions of precursors during the formation of the oxide films, i. e. sol-gel type routes, metallo-organic decomposition routes, hybrid routes, etc. While the development of sol-gel type processes for optical coatings on glass by silicon dioxide and titanium dioxide dates from the mid-20th century, the first CSD derived electronic oxide thin films, such as lead zirconate titanate, were prepared in the 1980’s. Since then CSD has emerged as a highly flexible and cost-effective technique for the fabrication of a very wide variety of functional oxide thin films. Application areas include, for example, integrated dielectric capacitors, ferroelectric random access memories, pyroelectric infrared detectors, piezoelectric micro-electromechanical systems, antireflective coatings, optical filters, conducting-, transparent conducting-, and superconducting layers, luminescent coatings, gas sensors, thin film solid-oxide fuel cells, and photoelectrocatalytic solar cells. In the appendix detailed “cooking recipes” for selected material systems are offered.
