Download or read book Sliding Mode Fuzzy Controllers written by Mojtaba Ahmadieh Khanesar and published by Springer Nature. This book was released on 2021-07-21 with total page 237 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses some of the challenges suffered by the well-known and robust sliding-mode control paradigm. The authors show how the fusion of fuzzy systems with sliding-mode controllers can alleviate some of these problems and promote applicability. Fuzzy systems used as soft switches eliminate high-frequency signal oscillations and can substantially lower the noise sensitivity of sliding-mode controllers. The amount of a priori knowledge required concerning the nominal structure and parameters of a nonlinear system is also shown to be much reduced by exploiting the general function-approximation property of fuzzy systems so as to use them as identifiers. The main features of this book include: • a review of various existing structures of sliding-mode fuzzy control; • a guide to the fundamental mathematics of sliding-mode fuzzy controllers and their stability analysis; • state-of-the-art procedures for the design of a sliding-mode fuzzy controller; • source codes including MATLAB® and Simulink® codes illustrating the simulation of these controllers, particularly the adaptive controllers; • a short bibliography for each chapter for readers interested in learning more on a particular subject; and • illustrative examples and simulation results to support the main claims made in the text. Academic researchers and graduate students interested in the control of nonlinear systems and particularly those working in sliding-mode controller design will find this book a valuable source of comparative information on existing controllers and ideas for the development of new ones.
Download or read book Model Based Fuzzy Control written by Rainer Palm and published by Springer Science & Business Media. This book was released on 1997 with total page 204 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction to model based fuzzy control; The FLC as a nonlinear transfer element; model based design of sliding mode FLC; Model based design of Takagi-Sugeno FLCs; References; Index.
Download or read book Model Based Fuzzy Control written by Rainer Palm and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 195 pages. Available in PDF, EPUB and Kindle. Book excerpt: Model Based Fuzzy Control uses a given conventional or fuzzy open loop model of the plant under control to derive the set of fuzzy rules for the fuzzy controller. Of central interest are the stability, performance, and robustness of the resulting closed loop system. The major objective of model based fuzzy control is to use the full range of linear and nonlinear design and analysis methods to design such fuzzy controllers with better stability, performance, and robustness properties than non-fuzzy controllers designed using the same techniques. This objective has already been achieved for fuzzy sliding mode controllers and fuzzy gain schedulers - the main topics of this book. The primary aim of the book is to serve as a guide for the practitioner and to provide introductory material for courses in control theory.
Download or read book Advanced Sliding Mode Control for Mechanical Systems written by Jinkun Liu and published by Springer Science & Business Media. This book was released on 2012-09-07 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Advanced Sliding Mode Control for Mechanical Systems: Design, Analysis and MATLAB Simulation" takes readers through the basic concepts, covering the most recent research in sliding mode control. The book is written from the perspective of practical engineering and examines numerous classical sliding mode controllers, including continuous time sliding mode control, discrete time sliding mode control, fuzzy sliding mode control, neural sliding mode control, backstepping sliding mode control, dynamic sliding mode control, sliding mode control based on observer, terminal sliding mode control, sliding mode control for robot manipulators, and sliding mode control for aircraft. This book is intended for engineers and researchers working in the field of control. Dr. Jinkun Liu works at Beijing University of Aeronautics and Astronautics and Dr. Xinhua Wang works at the National University of Singapore.
Download or read book Applications of Various Fuzzy Sliding Mode Controllers in Induction Motor Drives written by Ali Saghafinia and published by Nova Science Publishers. This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains publications on various fuzzy sliding mode speed controllers (FSMCs) based on the boundary layer approaches in the area of an indirect field-oriented control (IFOC) for Induction Motor (IM) drive, which include development and implementation FSMCs and related fields. The publications within Applications of Various Fuzzy Sliding Mode Controllers in Induction Motor Drives cover significant and recent developments of both foundational and applicable character in the field. With the exception of some basic notions in sliding mode control (SMC), field-oriented control (FOC), and fuzzy theory, the book is completely self-contained. Important concepts in FSMCs and its use in high performance IM are carefully motivated and introduced. Specifically, the authors have excluded any technical material that does not contribute directly to the understanding of SMC, FOC or fuzzy theory. Many other excellent textbooks are available today that discuss fuzzy, FOC and SMC in much more technical detail than that which is provided here.
Download or read book An Introduction to Fuzzy Control written by Dimiter Driankov and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 329 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fuzzy controllers are a class of knowledge based controllers using artificial intelligence techniques with origins in fuzzy logic. They can be found either as stand-alone control elements or as integral parts of a wide range of industrial process control systems and consumer products. Applications of fuzzy controllers are an established practice for Japanese manufacturers, and are spreading in Europe and America. The main aim of this book is to show that fuzzy control is not totally ad hoc, that there exist formal techniques for the analysis of a fuzzy controller, and that fuzzy control can be implemented even when no expert knowledge is available. The book is mainly oriented to control engineers and theorists, although parts can be read without any knowledge of control theory and may interest AI people. This 2nd, revised edition incorporates suggestions from numerous reviewers and updates and reorganizes some of the material.
Download or read book Sliding Mode Control Using MATLAB written by Jinkun Liu and published by Academic Press. This book was released on 2017-05-25 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sliding Mode Control Using MATLAB provides many sliding mode controller design examples, along with simulation examples and MATLAB® programs. Following the review of sliding mode control, the book includes sliding mode control for continuous systems, robust adaptive sliding mode control, sliding mode control for underactuated systems, backstepping, and dynamic surface sliding mode control, sliding mode control based on filter and observer, sliding mode control for discrete systems, fuzzy sliding mode control, neural network sliding mode control, and sliding mode control for robot manipulators. The contents of each chapter are independent, providing readers with information they can use for their own needs. It is suitable for the readers who work on mechanical and electronic engineering, electrical automation engineering, etc., and can also be used as a teaching reference for universities. Provides many sliding mode controller design examples to help readers solve their research and design problems Includes various, implementable, robust sliding mode control design solutions from engineering applications Provides the simulation examples and MATLAB programs for each sliding mode control algorithm
Download or read book Applications of Sliding Mode Control written by Nabil Derbel and published by Springer. This book was released on 2016-10-14 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents essential studies and applications in the context of sliding mode control, highlighting the latest findings from interdisciplinary theoretical studies, ranging from computational algorithm development to representative applications. Readers will learn how to easily tailor the techniques to accommodate their ad hoc applications. To make the content as accessible as possible, the book employs a clear route in each paper, moving from background to motivation, to quantitative development (equations), and lastly to case studies/illustrations/tutorials (simulations, experiences, curves, tables, etc.). Though primarily intended for graduate students, professors and researchers from related fields, the book will also benefit engineers and scientists from industry.
Download or read book Advances and Applications in Sliding Mode Control systems written by Ahmad Taher Azar and published by Springer. This book was released on 2014-11-01 with total page 592 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the advances and applications in Sliding mode control (SMC) which is widely used as a powerful method to tackle uncertain nonlinear systems. The book is organized into 21 chapters which have been organised by the editors to reflect the various themes of sliding mode control. The book provides the reader with a broad range of material from first principles up to the current state of the art in the area of SMC and observation presented in a clear, matter-of-fact style. As such it is appropriate for graduate students with a basic knowledge of classical control theory and some knowledge of state-space methods and nonlinear systems. The resulting design procedures are emphasized using Matlab/Simulink software.
Download or read book Sliding Mode Control of Switching Power Converters written by Siew-Chong Tan and published by CRC Press. This book was released on 2018-09-03 with total page 301 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sliding Mode Control of Switching Power Converters: Techniques and Implementation is perhaps the first in-depth account of how sliding mode controllers can be practically engineered to optimize control of power converters. A complete understanding of this process is timely and necessary, as the electronics industry moves toward the use of renewable energy sources and widely varying loads that can be adequately supported only by power converters using nonlinear controllers. Of the various advanced control methods used to handle the complex requirements of power conversion systems, sliding mode control (SMC) has been most widely investigated and proved to be a more feasible alternative than fuzzy and adaptive control for existing and future power converters. Bridging the gap between power electronics and control theory, this book employs a top-down instructional approach to discuss traditional and modern SMC techniques. Covering everything from equations to analog implantation, it: Provides a comprehensive general overview of SMC principles and methods Offers advanced readers a systematic exposition of the mathematical machineries and design principles relevant to construction of SMC, then introduces newer approaches Demonstrates the practical implementation and supporting design rules of SMC, based on analog circuits Promotes an appreciation of general nonlinear control by presenting it from a practical perspective and using familiar engineering terminology With specialized coverage of modeling and implementation that is useful to students and professionals in electrical and electronic engineering, this book clarifies SMC principles and their application to power converters. Making the material equally accessible to all readers, whether their background is in analog circuit design, power electronics, or control engineering, the authors—experienced researchers in their own right—elegantly and practically relate theory, application, and mathematical concepts and models to corresponding industrial targets.
Download or read book Magnetic Bearings written by Gerhard Schweitzer and published by Springer Science & Business Media. This book was released on 2009-06-10 with total page 541 pages. Available in PDF, EPUB and Kindle. Book excerpt: Compiling the expertise of nine pioneers of the field, Magnetic Bearings - Theory, Design, and Application to Rotating Machinery offers an encyclopedic study of this rapidly emerging field with a balanced blend of commercial and academic perspectives. Every element of the technology is examined in detail, beginning at the component level and proceeding through a thorough exposition of the design and performance of these systems. The book is organized in a logical fashion, starting with an overview of the technology and a survey of the range of applications. A background chapter then explains the central concepts of active magnetic bearings while avoiding a morass of technical details. From here, the reader continues to a meticulous, state-of-the-art exposition of the component technologies and the manner in which they are assembled to form the AMB/rotor system. These system models and performance objectives are then tied together through extensive discussions of control methods for both rigid and flexible rotors, including consideration of the problem of system dynamics identification. Supporting this, the issues of system reliability and fault management are discussed from several useful and complementary perspectives. At the end of the book, numerous special concepts and systems, including micro-scale bearings, self-bearing motors, and self-sensing bearings, are put forth as promising directions for new research and development. Newcomers to the field will find the material highly accessible while veteran practitioners will be impressed by the level of technical detail that emerges from a combination of sophisticated analysis and insights gleaned from many collective years of practical experience. An exhaustive, self-contained text on active magnetic bearing technology, this book should be a core reference for anyone seeking to understand or develop systems using magnetic bearings.
Download or read book Fuzzy Control written by Kai Michels and published by Springer. This book was released on 2007-05-31 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a critical discussion of fuzzy controllers from the perspective of classical control theory. Special emphasis is placed on topics of importance for industrial applications, including self-tuning of fuzzy controllers, optimisation and stability analysis. The text begins with a detailed introduction to fuzzy systems and control theory, and guides the reader to a thorough understanding of up-to-date research results.
Download or read book Universal Fuzzy Controllers for Non affine Nonlinear Systems written by Qing Gao and published by Springer. This book was released on 2016-07-19 with total page 142 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis provides a systematic and integral answer to an open problem concerning the universality of dynamic fuzzy controllers. It presents a number of novel ideas and approaches to various issues including universal function approximation, universal fuzzy models, universal fuzzy stabilization controllers, and universal fuzzy integral sliding mode controllers. The proposed control design criteria can be conveniently verified using the MATLAB toolbox. Moreover, the thesis provides a new, easy-to-use form of fuzzy variable structure control. Emphasis is given to the point that, in the context of deterministic/stochastic systems in general, the authors are in fact discussing non-affine nonlinear systems using a class of generalized T-S fuzzy models, which offer considerable potential in a wide range of applications.
Download or read book Advances in Sliding Mode Control written by B Bandyopadhyay and published by Springer. This book was released on 2013-03-15 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: The sliding mode control paradigm has become a mature technique for the design of robust controllers for a wide class of systems including nonlinear, uncertain and time-delayed systems. This book is a collection of plenary and invited talks delivered at the 12th IEEE International Workshop on Variable Structure System held at the Indian Institute of Technology, Mumbai, India in January 2012. After the workshop, these researchers were invited to develop book chapters for this edited collection in order to reflect the latest results and open research questions in the area. The contributed chapters have been organized by the editors to reflect the various themes of sliding mode control which are the current areas of theoretical research and applications focus; namely articulation of the fundamental underpinning theory of the sliding mode design paradigm, sliding modes for decentralized system representations, control of time-delay systems, the higher order sliding mode concept, results applicable to nonlinear and underactuated systems, sliding mode observers, discrete sliding mode control together with cutting edge research contributions in the application of the sliding mode concept to real world problems. This book provides the reader with a clear and complete picture of the current trends in Variable Structure Systems and Sliding Mode Control Theory.
Download or read book Sliding Mode Control and Observation written by Yuri Shtessel and published by Springer Science & Business Media. This book was released on 2013-06-01 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: The sliding mode control methodology has proven effective in dealing with complex dynamical systems affected by disturbances, uncertainties and unmodeled dynamics. Robust control technology based on this methodology has been applied to many real-world problems, especially in the areas of aerospace control, electric power systems, electromechanical systems, and robotics. Sliding Mode Control and Observation represents the first textbook that starts with classical sliding mode control techniques and progresses toward newly developed higher-order sliding mode control and observation algorithms and their applications. The present volume addresses a range of sliding mode control issues, including: *Conventional sliding mode controller and observer design *Second-order sliding mode controllers and differentiators *Frequency domain analysis of conventional and second-order sliding mode controllers *Higher-order sliding mode controllers and differentiators *Higher-order sliding mode observers *Sliding mode disturbance observer based control *Numerous applications, including reusable launch vehicle and satellite formation control, blood glucose regulation, and car steering control are used as case studies Sliding Mode Control and Observation is aimed at graduate students with a basic knowledge of classical control theory and some knowledge of state-space methods and nonlinear systems, while being of interest to a wider audience of graduate students in electrical/mechanical/aerospace engineering and applied mathematics, as well as researchers in electrical, computer, chemical, civil, mechanical, aeronautical, and industrial engineering, applied mathematicians, control engineers, and physicists. Sliding Mode Control and Observation provides the necessary tools for graduate students, researchers and engineers to robustly control complex and uncertain nonlinear dynamical systems. Exercises provided at the end of each chapter make this an ideal text for an advanced course taught in control theory.
Download or read book Recent Advances in Sliding Modes From Control to Intelligent Mechatronics written by Xinghuo Yu and published by Springer. This book was released on 2015-04-10 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is dedicated to Professor Okyay Kaynak to commemorate his life time impactful research and scholarly achievements and outstanding services to profession. The 21 invited chapters have been written by leading researchers who, in the past, have had association with Professor Kaynak as either his students and associates or colleagues and collaborators. The focal theme of the volume is the Sliding Modes covering a broad scope of topics from theoretical investigations to their significant applications from Control to Intelligent Mechatronics.
Download or read book Sliding Mode Control written by Christopher Edwards and published by CRC Press. This book was released on 1998-08-27 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the formation of any control problem there will be discrepancies between the actual plant and the mathematical model for controller design. Sliding mode control theory seeks to produce controllers to over some such mismatches. This text provides the reader with a grounding in sliding mode control and is appropriate for the graduate with a basic knowledge of classical control theory and some knowledge of state-space methods.
